B-K lighting SQUARE ADJUSTABLE WELL STAR User manual

SQUARE ADJUSTABLE WELL STAR™
Installation Instructions
SUBMITTAL DATE
12-12-11
REFERENCE NUMBER
INS000969
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
2. Supply low voltage wiring necessary for
installation (By Others)
NOTE: Leave sufficient wire length in the
fixture housing for future service.
Finished grade
12”
Finished grade
1. Excavate trench according to designed lighting
plan 20” deep and 10” wide suitable for the 1.
Excavate trench according to designed lighting
plan 20” deep and 10” wide suitable for the 13”
fixture housing.
3. Remove faceplate from housing using 3/16” allen
wrench.
4. Place housing in excavated trench and pull wire
through housing.
Finished grade
TOOLS
NEEDED:
By Others
3/16” Allen wrench
Wire connectors
(recommended silicone filled wire connectors)
Standard phillips screwdriver
This set of instructions
works for:
SW - Square
Adjustable
Well Star™
SW
SW Composite Housing
Brass Faceplate and
Concrete Pour Collar
5’ of 18 gauge
wire
TECHNOLOGY
with
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
Hot Surface
Warning High Voltage

PROJECT:
TYPE:
SUBMITTAL DATE
12-12-11
REFERENCE NUMBER
INS000969
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
ETL LISTED
CONFORMS TO ANSI/UL
STANDARD 1838 AND UL SUBJECT 8750
CERTIFIED TO CAN/CSA
STANDARD C22.2 NO. 9
SQUARE ADJUSTABLE WELL STAR
Installation Instructions
5. Align and orientate Concrete Pour Collar on
housing to illuminated object. Back fill with pea
gravel or sand to allow sufficient drainage. Install
housing flush at grade. See wiring diagram.
6. Make two water tight, low voltage connections
using proper wire connectors (By Others).
7. Loosen stainless steel phillips head cap screw
on adjustable bracket, aim to desired location.
Tighten to maintain aiming position.
Pea gravel or sand
Finished grade
Dirt or soil
LINE 12V
FIXTURE
COM
Remote
Transformer
COM
8. Attach faceplate to Concrete Pour Collar with four
screws using a 3/16” Allen wrench.
Finished grade
1. Remove mounting screws. 2. Rotate large bracket 45º.
3. Secure mounting screw.
To Change Lamp Tilt Orientation
TECHNOLOGY
with

SUBMITTAL DATE
12-12-11
REFERENCE NUMBER
INS000969
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
ETL LISTED
CONFORMS TO ANSI/UL
STANDARD 1838 AND UL SUBJECT 8750
CERTIFIED TO CAN/CSA
STANDARD C22.2 NO. 9
PROJECT:
TYPE:
SQUARE ADJUSTABLE WELL STAR
Installation Instructions
TECHNOLOGY
with
To Change Lumen Output (when required).
1. Use 5/64” Allen wrench to loosen #8-32
stainless set screw and remove cap.
3. Place cap on fixture and tighten set screw.2. With flat head screw driver rotate dial to
desired lumen output.
This product is available with Adjust-e-Lume™ (Patent Pend.) for Dynamic Lumen Output Control
Warning! The light output of this product may be dynamically adjusted as desired to raise and lower light levels. Please ensure the xture is set
to the appropriate light level desired during installation.