B-K lighting RE1 User manual

TOOLS
NEEDED:
3/32”, 1/8” & 7/64” Allen Wrench
Waterproof Wire Connectors
Epoxy (Supplied)
Sleeve or Wedge Anchors for Concrete (1/4” Dia. Min.)
Data Cable (RE3 Option Only)
Receptacle Bollard
Warning High Voltage
Installation Instructions
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
CONCRETE INSTALLATION ONLY
RE1 Option - GFI
PVC (Optional)
Primary 3/4”
Conduit
Connectors
Machined
Aluminum
Housing
(2) 3/4” x 3/4”
Opening for Cord
Sets
Machined Base
Receptacle
(Option Varies)
Grade Label
Epoxy
RE2 Option - GFI & USB
RE3 Option - RJ45 Jack
Cover with
Captive Tamper
Resistant Screw
Tenon
Steel Plate
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION
INSTRUCTIONS
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY
TO PERSONS IMPORTANT
SAFETY INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before
replacing lamp/LED. Fixture gets HOT quickly!
Contact only switch/plug when turning
on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time.
Use a soft cloth or gloves. Oil from skin may cause
damage.
SAVE THESE INSTRUCTIONS
RELEASE DATE
12/21/2021
REFERENCE NUMBER
INS-2701-00
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR
SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all
Local and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping
of this product.
• Before wiring to power supply and during servicing or
relamping, turn off power at fuse or circuit breaker before
service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause
an unsafe condition. The use of damaged components may
cause an unsafe condition and void product warranty.
• Do not block light emanating from product in whole or
part, as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time.
Use a clean, dry, soft cloth to handle the lamp. Oil from
skin may damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept
clean during installation and service; failure to do this may
cause an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL
SAFETY AND INSTALLATION INSTRUCTIONS
Proper soil preparation is recommended before installation. See the DIG-IT guide at bklighting.com/collaterals/install/digit.pdf
for more information.

40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
RELEASE DATE
12/21/2021
REFERENCE NUMBER
INS-2701-00
2. Connect conduit to the 3/4” primary conduit
couplers attached to the bottom of the PVC
housing. Place PVC housing in hole.
3. Prep for concrete. Base is flush with finished
grade.
4. Pull branch circuit wiring necessary for
appropriate installation.
1. Excavate trench according to designed lighting
plan. Dig hole a minimum of 24” deep and
10” wide to accommodate PVC housing at
desired fixture location and direction of in-use
receptacle(s).
Finished grade
Pea Gravel
or Sand
Concrete
Finished Grade
GRADE
GRADE
Finished gradePea Gravel
or Sand
Concrete
Finished Grade
GRADE
GRADE
Finished grade
Pea Gravel
or Sand
Concrete
Finished Grade
GRADE
GRADE
PVC HOUSING MUST BE INSTALLED AS PER GRADE LABEL. HOUSING IS LABELED AT GRADE
LEVEL. HOUSING INSTALLED BELOW GRADE WILL VOID WARRANTY
Align holes
for screw
orientation
3. Prepare epoxy (included) according to
instructions on packaging.
INSTALLATION OF BASE
6. Place base onto epoxyed PVC housing over
steel plate, lining up with steel plate mounting
holes and drilled mounting holes in concrete.
4. Use mixing stick to apply the epoxy to the
exterior of exposed PVC housing as shown, in
smooth, continuous application.
1. Steel plate and base has four (4) 5/16” dia. holes
at 3” square on center for mounting hardware.
Use steel plate as template for final mounting
drill hole positions.
2. Drill four (4) holes into concrete for minimum 1/4”
sleeve or wedge anchors for concrete. Clean or
vacuum debris from drilled holes.
Minimum of 1/4” dia. anchors must be used.
5. Place steel plate epoxyed PVC housing, lining
up with drilled mounting holes in concrete.
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
Receptacle Bollard
Installation Instructions
INSTALLATION OF PVC MOUNTING

40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
RELEASE DATE
12/21/2021
REFERENCE NUMBER
INS-2701-00
LINE
COM
GROUND GROUND
BASE
In-Use
Receptacle
DATA In-Use
Receptacle
RJ45
WIRING DIAGRAM
1. Pull branch circuit wiring. Make watertight
connections from primary branch circuit
to in-use receptacle using waterproof wire
connectors. Connect incoming ground and
ground from receptacle to ground wire on
base. See wiring diagram.
INSTALLATION OF IN-USE RECEPTACLE (RE1 & RE2 Option)
2. Attach ground from branch circuit to screw
on anchor base. Place connectors inside
receptacle.
3. Attach in-use receptacle to installed anchor
base with four (4) #10-32 button head stainless
steel cap screws at the base using a 1/8” allen
wrench.
4. Receptacle cover has captive #6-32 screw.
Secure receptacle by tightening captive #6-32
set screw using a 7/64” allen wrench.
Receptacle cover has two (2) openings for
in-use cord sets.
7. Mount base and plate to concrete using
mounting holes drilled previously (Mounting
Hardware by Others). Minimum 1/4” diameter
sleeve or wedge anchors for concrete must be
used.
9. Seal base and plate as per NEC. Continue with
installation of In-Use Receptacle option chosen.
8. Tighten four (4) #10-32 screws in base using a
3/32” allen wrench to secure to installed PVC
housing.
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
Receptacle Bollard
Installation Instructions

40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
RELEASE DATE
12/21/2021
REFERENCE NUMBER
INS-2701-00
LINE
COM
GROUND GROUND
BASE
In-Use
Receptacle
DATA In-Use
Receptacle
RJ45
WIRING DIAGRAM 5. Place connection(s) and/or cable inside
receptacle.
6. Attach in-use receptacle to installed anchor
base and plate with four (4) #10-32 button
head stainless steel cap screws at the base
using a 1/8” allen wrench.
7. Receptacle cover has captive #6-32 screw.
Secure receptacle by tightening captive #6-32
set screw using a 7/64” allen wrench.
Receptacle cover has two (2) openings for
in-use cord sets.
4. Place connections into bollard. Attach inner
bracket with RJ45 jack with two (2) #6-32
screws with a 7/64” allen wrench.
INSTALLATION OF IN-USE RECEPTACLE (RE3 Option)
2. Loosen two (2) #6-32 screws with a 7/64”
allen wrench to remove inner bracket with
RJ45 jack.
3. Connect incoming data cable to RJ45 jack as
per installation plan. Follow manufacturer’s
instructions as per cable and method of
connection to RJ45 jack (cable and connections
required By Others). See wiring diagram.
1. Open receptacle cover. Receptacle cover has
captive #6-32 screw for use with a 7/64” allen
wrench.
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
Receptacle Bollard
Installation Instructions