B-K lighting DENALI User manual

Hot SurfaceHigh VoltageWarning
Standard Installation
DENALI
SURFACE MOUNT - INTEGRAL
Flammable
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL
SAFETY AND INSTALLATION INSTRUCTIONS
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.
• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.
• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY
TO PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before
replacing lamp/LED. Fixture gets HOT quickly!
Contact only switch/plug when turning on.
Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time.
Use a soft cloth or gloves. Oil from skin may cause
damage.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
5/32” Allen Wrench
Phillips Screwdriver
Waterproof Wire Connectors
TOOLS
NEEDED:
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION
INSTRUCTIONS
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL
ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
RELEASE DATE
06/26/2023
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
REFERENCE NUMBER
INS-2824-00
SM-DE
Universal
Mounting Ring

Phase 2 - Finish Installation of Fixture with Remote Driver
RELEASE DATE
10/25/2022
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
REFERENCE NUMBER
INS-2815-00
RELEASE DATE
06/26/2023
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
REFERENCE NUMBER
INS-2824-00
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
Standard Installation
DENALI
SURFACE MOUNT - INTEGRAL
4. Mount fixture using two (2) #10-24 hex screws to
installed back box. Seal building envelope as per
NEC. Do not overtighten.
1. Install universal mounting ring (included with
fixture) using #10-24 screws onto back box. Align
fixture mounting holes to final mounting position.
2. Pull primary branch circuit wiring out of back box.
Leave sufficient wiring for any future service and
maintenance.
WIRING DIAGRAM
3. Make watertight connections from branch circuit
wiring to fixure leads using waterproof wire
connectors (not included) in splice location as
per NEC. Connect incoming green ground wire to
ground wire from fixture. See wiring diagram.
All line voltage connections must be made in
compliance with the National Electrical Code.
Failure to do o will void warranty.
HOT (BLACK)
GROUND (GREEN) GROUND FIXTURE
NEUTRAL
HOT
NEUTRAL (WHITE)
WIRING DIAGRAM - Dimming
HOT (BLACK)
GROUND (GREEN) GROUND
FIXTURE
NEUTRAL
HOT
NEUTRAL (WHITE)
DIM + DIM +
DIM -
DIM -
Phase 1 - Rough In
Installation of Back box
1. Install conduit (not included) to be used
with this product.
2. Install junction box so that front face is
flush with finished wall or ceiling. Seal
building envelope as per NEC.
3. Connect box to conduit and pull wires for
connections (See wiring diagram).
Additional Info
• Please follow National and Local electrical codes for your area.
• Use 4” round cast box (not included).
• Suitable for through wire.
• Suitable for installation into combustible materials.
• Rated for 90° C.
• Junction box, universal mounting ring screws, box mounting
hardware and gaskets (not included).

RELEASE DATE
10/25/2022
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
REFERENCE NUMBER
INS-2815-00
RELEASE DATE
06/26/2023
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
REFERENCE NUMBER
INS-2824-00
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
3. Remove retainer.2. Twist and pull away optic.1. Loosen three (3) #8-32 set screws with a 5/64”
allen wrench on cap, then remove cap.
8. Connect new driver assembly to fixture leads. Place
connections inside body cavity, then slide down
fixture body along guides.
4. Disconnect driver assembly from fixture body.
5. Separate heatsink from driver assembly via quick
disconnect.
11. Install cap by tightening three (3) #8-32 set screws
with a 5/64” allen wrench. Do not over tighten.
Cap should be able to rotate without force.
10. Twist to reinstall optic onto optic holder.
6. Remove protective plastic from the double-sided
tape square on clean top of driver assembly.
7. Reconnect heatsink assembly to driver assembly
via quick disconnect. Quick disconnect tucks into
space underneath heatsink. Press heatsink down
along guides until flush and even with tape on
driver.
9. Reinstall retainer.
LINE UP WITH THE HOLE
Integral Driver Replacement
Standard Installation
DENALI
SURFACE MOUNT - INTEGRAL