B-K lighting ArtiStar Remote User manual

NEEDED
FOR
INSTALLATION:
9/64” Allen Wrench
Waterproof Wire Connector
Warning Flammable Hot Surface
PVC Housing
UL-AR
Stability Flange
Body
Faceplate
18 Ga. Wire
Flush Mount
Collar
Low Voltage
ARTISTAR UPLIGHT
Flush Mount
Standard Installation
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL
SAFETY AND INSTALLATION INSTRUCTIONS
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.
• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.
• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY
TO PERSONS IMPORTANT
SAFETY INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before
replacing lamp/LED. Fixture gets HOT quickly!
Contact only switch/plug when turning on.
Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time.
Use a soft cloth or gloves. Oil from skin may cause
damage.
SAVE THESE INSTRUCTIONS
Proper soil preparation is recommended before installation. See the DIG-IT guide at
www.bklighting.com/collaterals/install/digit.pdf for more information.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION
INSTRUCTIONS
RELEASE DATE
12/15/2021
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR
SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
REFERENCE NUMBER
INS-2317-00
Please refer to the low
voltage design guide at www.
bklighting.com/lvguide before
installation for proper wire
selection.

Finished grade
12”
Finished grade
8 3/4”
LINE 12V
FIXTURE
COM
Remote
Transformer
COM
Screws on faceplate will
align with alignment
arrows on temporary
cover
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Finished grade
Concrete
Wire nuts must
clear opening
6”
min.
Finished grade
15”
5. Align holes to final installation orientation.
Arrows on temporary cover point towards
screw location on faceplate for alignment
purposes.
NOTE: Do not remove temporary cover until
installation of faceplate.
Finished grade
12”
Finished grade
8 3/4”
LINE 12V
FIXTURE
COM
Remote
Transformer
COM
Screws on faceplate will
align with alignment
arrows on temporary
cover
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Finished grade
Concrete
Wire nuts must
clear opening
6”
min.
Finished grade
15”
1. Excavate trench according to designed
lighting plan 12” deep and 12” wide suitable
for the fixture housing.
2. Supply low voltage wiring necessary for
installation.
3. Slide stability flange onto housing.
NOTE: Product is supplied with a
stability flange to anchor fixture and aid in
installation.
4. Loop minimum of 6” of low voltage wire inside
housing to allow for fixture service. Place
fixture in hole.
NOTE: Do not remove temporary cover!
Fixture Installation
6. Per DIG-IT Guide, backfill the gap between
the bottom of housing and bottom of hole with
sand or pea gravel for drainage.
NOTE: The mounting collar must be flush to
finished grade. Use stability flange to aid in
installation as shown.
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
7. Fill the hole around the fixture housing to 12”
below the finished grade with clean fill dirt and
tamp carefully to prevent settling of fixture.
Pour concrete and finish as required flush with
mounting collar.
RELEASE DATE
12/15/2021
REFERENCE NUMBER
INS-2317-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
B-K LIGHTING
ARTISTAR UPLIGHT
Flush Mount
Standard Installation
Soil Prep
Conduit
trench
B. Dig hole 10” wide and 10” deep.
Conduit
Trench
Excavated
for Housing
C. Prep soil according to DIG-IT Guide.A. Determine Soil Type by referencing DIG-IT
Guide. Prep soil according to DIG-IT Guide.

Finished grade
Concrete
Wire nuts must
clear opening
6”
min.
9. Access low voltage wire inside power pipe. Make
two water tight, low voltage connections using
proper wire connectors. Wire nuts must clear
opening. Insert fixture and low voltage wire into
housing. See wiring diagram.
10. Mount faceplate to collar using two (2) #8-32
flat head screws (included) with a 9/64” allen
wrench.
WIRING DIAGRAM
LED - For use with 12VAC LED remote
transformer or magnetic transformers only.
B-K Lighting cannot guarantee performance
with third party manufacturers’ transformers.
8. Remove temporary cover and pull out low
voltage wire.
RELEASE DATE
12/15/2021
REFERENCE NUMBER
INS-2317-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
B-K LIGHTING
ARTISTAR UPLIGHT
Flush Mount
Standard Installation
HOT 12V
12V
FIXTURE
NEUTRAL
Remote
Transformer

1. Remove faceplate from collar using two (2) #8-32
flat head screws (included) with a 9/64” allen
wrench.
Fixture Relamping
2. Remove fixture from collar. 3. Loosen two (2) #8-32 screw with a 5/64” allen
wrench to remove faceplate.
4. Space three fingers evenly around the optic and
gently rock optic to remove.
6. Disengage LED board and driver assembly.
Replace with new board and driver assembly.
7. Reverse install LED board and driver by carefully
engaging quick disconnects and inserting into
fixture body. Secure LED board in place with
stainless steel screws. Snap optics in place.
8. With flat head screw driver rotate dial to desired
lumen output. Replace fixture in mounting collar.
5. Use a 5/64” allen wrench to remove two (2) #2-56
socket head cap screws on LED board, grasp
LED board and gently pull up to expose quick
disconnect.
9. Mount faceplate to collar using two (2) #8-32 flat
head screws (included) with a 9/64” allen wrench.
Do not overtighten.
RELEASE DATE
12/15/2021
REFERENCE NUMBER
INS-2317-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
B-K LIGHTING
ARTISTAR UPLIGHT
Flush Mount
Standard Installation