B-K lighting Nite Star User manual

RELEASE DATE
01/20/2021
REFERENCE NUMBER
INS000929.2
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR
SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
5/32” and 5/64” Allen Wrench
Waterproof Wire Connectors
Mallet or Sledge Hammer
Warning Hot Surface
NEEDED
FOR
INSTALLATION:
By Others
Nite Star (NS)
Low Voltage
Standard Installation
Knuckle
Stake
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all
Local and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping
of this product.
• Before wiring to power supply and during servicing or
relamping, turn off power at fuse or circuit breaker before
service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause
an unsafe condition. The use of damaged components may
cause an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL
SAFETY AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin
may damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept
clean during installation and service; failure to do this may
cause an unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY
TO PERSONS IMPORTANT
SAFETY INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO
PERSONS:
Turn off/unplug and allow to cool before replacing
lamp.
Lamp gets HOT quickly! Contact only switch/plug
when turning on.
Do not touch hot lens, guard, or enclosure (see
diagram/picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations · Additionally suitable for mounting within 4 ft. of the ground
IMPORTANT LISTINGS AND CERTIFICATIONS
NS-Nite Star
Please refer to the low voltage design guide at www.bklighting.com/lvguide before installation for proper wire
selection.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION
INSTRUCTIONS

RELEASE DATE
01/20/2021
REFERENCE NUMBER
INS000929.2
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
Nite Star (NS)
Low Voltage
Standard Installation
Fixture Installation with Stake
4. Attach the fixture to the threads on the stake.
Make sure the stake is secured in the ground.
2. Remove the locknut from the fixture, leave
the o-ring on the threads.
5. Make watertight connections from remote
transformer to fixture leads using waterproof
wire connectors (by others). See wiring
diagram.
6. Use a 5/32” allen wrench to slightly loosen
#10-32 stainless steel black oxide socket
head cap screw at the knuckle for aiming
purposes. Tighten to secure desired location.
LINE 12V
Fixture
COM
Remote
Transformer
COM
WIRING DIAGRAM
For use with 12VAC remote
transformer.
Finished Grade
1. Drive the stake into the ground with a mallet
or a small sledge hammer (by others). Make
sure the top is flush with the finished grade.
Finished Grade
3. Pull the fixture wire cable throught the
stake’s center where the hole is located. Silce
moved the fixture wire from under the stake
to the side to make a connection with the low
voltage direct burial cable (by others).
Ground wire connections is based off of
local code requirements.
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION
INSTRUCTIONS

RELEASE DATE
01/20/2021
REFERENCE NUMBER
INS000929.2
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
Nite Star (NS)
Low Voltage
Standard Installation
Fixture Installation with Standard Knuckle
1. Mount knuckle onto suitable enclosure
according to designed lighting plan.
2. Secure ½” NPS stem to mounting option.
Secure with provided locknut if applicable.
3. Make watertight connections from remote
transformer to lamp leads using waterproof
wire connectors (by others). See wiring
diagram.
4. Use a 5/32” allen wrench to slightly loosen
#10-32 stainless steel black oxide socket
head cap screw at the knuckle for aiming
purposes. Tighten to secure desired location.
LINE 12V
Fixture
COM
Remote
Transformer
COM
WIRING DIAGRAM
For use with 12VAC remote
transformer.
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION
INSTRUCTIONS