B-K lighting TETON User manual

Hot SurfaceLow VoltageWarning
RELEASE DATE
10/25/2022
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL
ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
REFERENCE NUMBER
INS-2815-00
RELEASE DATE
08/02/2023
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
REFERENCE NUMBER
INS001156
Installation Instruction
TETON
LED
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION
INSTRUCTIONS
Flammable
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL
SAFETY AND INSTALLATION INSTRUCTIONS
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.
• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.
• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY
TO PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before
replacing lamp/LED. Fixture gets HOT quickly!
Contact only switch/plug when turning on.
Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time.
Use a soft cloth or gloves. Oil from skin may cause
damage.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
1/8” Allen Wrench
Phillips Screwdriver
Waterproof Wire Connectors
TOOLS
NEEDED:
Please refer to the low voltage design guide at www.bklighting.com/lvguide before installation for proper wire selection.
TT - Teton Fixture
Universal Mounting Ring

RELEASE DATE
10/25/2022
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
REFERENCE NUMBER
INS-2815-00
RELEASE DATE
08/02/2023
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
REFERENCE NUMBER
INS001156
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
Phase 2 - Finish Installation of Fixture with Remote Transformer
Installation Instruction
TETON
LED
1. Install universal mounting ring (supplied with
fixture) using #10-24 screws onto back box. Align
fixture mounting holes to final mounting position.
Universal mounting ring orientation determines
fixture orientation.
2. Make watertight connections from remote
transformer to fixture leads using waterproof wire
connectors (not included). See wiring diagram.
Phase 1 - Rough In
Installation of Back box
1. Install conduit (not included) to be used
with this product.
2. Install junction box so that front face
is flush with finished wall. Seal building
envelope as per NEC.
3. Connect box to conduit and pull wires for
connections (See Wiring diagram).
Additional Info
• Please follow National and Local electrical codes for your area.
• 4” round cast box.
• Suitable for through wire.
• Suitable for installation into combustible materials.
• Rated for 90° C.
• Junction box, universal mounting ring screws, box mounting
hardware and gaskets (not included).
3. Using a 1/8” allen wrench mount fixture using
two (2) #10-24 screws to installed back box.
Seal building envelope as per NEC. Do not
overtighten.
HOT12V
FIXTURE
NEUTRAL
Remote
Magnetic
Transformer
12v
WIRING DIAGRAM
LED - For use with 12VAC LED remote
transformer or magnetic transformers only. B-K
Lighting cannot guarantee performance with
third party manufacturers’ transformers.
Low Voltage - For use with 12VAC remote
transformer.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
Replacing LED Board/Driver and Optics
Replacing Low Voltage LED Lamps
RELEASE DATE
08/02/2023
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
REFERENCE NUMBER
INS001156.1
1. Use a 5/64” allen wrench to loosen #8-32 stainless
set screw and remove cap.
2. Space three fingers evenly around the optic and
gently rock optic to remove.
4. Disengage LED board and driver assembly. Replace
with new board and driver assembly.
5. Reverse install LED board and driver by carefully
wrapping 18 gauge wires around driver and
inserting into fixture body. Secure LED board in
place with stainless steel screws.
6. Snap optics in place. Place cap on fixture and
tighten set screw.
3. Use a 5/64” allen wrench to remove two (2) #2-56
socket head cap screws on LED board, grasp
LED board and gently pull up to expose quick
disconnect.
7. Use a 5/64” allen wrench on #8-32 stainless set
screw to secure cap.
1. Use a 5/64” allen wrench to loosen #8-32 stainless
set screw and remove cap.
3. Place cap on fixture and tighten set screw. Tighten
screw to 1/2 inch pounds. Top of screw should sit
flush with fixture cap.
Warning: Do not over tighten set screw. Doing
so will compromise o-ring seal and will void
warranty.
2. Firmly insert lamp pins into socket to make
connection. Rocking motion maybe required.
Do not exceed the maximum wattage listed on
the fixture label before installing.
Replacement/Installation Instructions
TETON
LED/LOW VOLTAGE LED LAMP