B-K lighting ArtiStar Series User manual

RELEASED
6-30-19
REFERENCE NUMBER
INS-2810-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
5/32”, 3/16”, 0.050”& 5/64”Allen Wrench
Waterproof Wire Connectors
Phillips Screwdriver
NEEDED
FOR
INSTALLATION:
By Others
This set of instructions
works for:
ArtiStar™ Series
Stainless Steel Tree Strap
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
Warning High Voltage
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.
• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.
• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time. Use
a soft cloth or gloves. Oil from skin may cause damage.
SAVE THESE INSTRUCTIONS
PTR-AR-TR
ArtiStar™ Power of X
For integral fixture
configurations
ArtiStar™ KnuckleTree Stand-Off Splice Box
Cable Quick
Disconnect
PALM TREE RING INTEGRAL
ArtiStar™ Series
Standard Installation

RELEASED
6-30-19
REFERENCE NUMBER
INS-2810-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
Fixture Installation
2. Place tree ring fixture around tree.
Move fixture to desired height. Tighten
the entire assembly to the tree with
provided stand-offs.
3. Secure by hooking end of strap over two (2)
Phillips screws. Secure by tightening two (2)
Phillips screws with Phillips screwdriver.
5. Bring line voltage cable from power line to
main splice box location. Loosen cord grip on
bottom of splice box, feed line voltage cable
from power line through, then tighten cord grip
to secure
5. Remove top of driver housing by removing (4)
#8-32 set screws using 5/64” Allen wrench.
Driver housing will be marked for primary.
WIRING DIAGRAM
7. Make watertight connections from primary
branch circuit to driver with waterproof wire
connectors. (By Others). Fixtures are pre-wired
at factory on the secondary side. See wiring
diagram.
120V
LED
COM
GROUND
Driver
GROUND IN HOUSING
Factory
Wired
8. Replace top of driver housing with (4) #8-32
screws with 5/64” Allen wrench.
4. Connect secondary cable then twist to secure
in place.
PALM TREE RING INTEGRAL
ArtiStar™ Series
Standard Installation

RELEASED
6-30-19
REFERENCE NUMBER
INS-2810-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
ArtiStar™ Knuckle
Warning: Do not over tighten set screw.
Doing so will compromise O-ring seal and will
void warranty.
1. Use 5/64” Allen wrench to loosen (3) #8-32
stainless steel set screws on fixture base. Rotate
fixture at base and aim fixture to desired
horizontal location, then tighten screw.
2. Use 3/16” Allen wrench to slightly loosen
¼”-28 stainless steel black oxide socket head
cap screw at the knuckle for vertical aiming
purposes, then tighten screw.
PALM TREE RING INTEGRAL
ArtiStar™ Series
Standard Installation
4. Install new LED assembly. Assembly can only
connect in one direction. Secure set screws
using 0.050” Allen wrench.
2. Remove optic by pulling gently and lift up.1. Use 5/64” Allen wrench to slightly loosen
three (3) #8-32 stainless steel set screws to
remove cap.
3. Use 0.050” Allen wrench to loosen three (3) set
screws holding LED assembly. Gently lift LED
assembly from fixture.
Handle with care.
5. Replace optic by lining notches with optic holder,
then pressing down gently until secured into place.
6. Place cap on fixture and tighten #8-32 set
screws with 5/64” Allen wrench. Top of
screws should sit flush with fixture cap.
Warning: Do not over tighten set screws.
Doing so will compromise O-Ring seal and
will void warranty.
Replacing LED and/or Optics