Backyard Creations 273-5112 User manual

PART
NO. PART QTY
1
2
3
4
5
6
7
8 2
4
4
2
1
4
1
1
1
1
2
2
2
2
4
10
11
12
13
14
15
16
17
18
19
20
21
22
23
MAGAZINE BAG
PILLOW
FABRIC
PLASTIC END CAP
WASHER d10.5*D21*2.0
WASHER d10.5*D32*4
BOLT M10*115
SIDE SUPPORT
CROSS BRACE
SIDE BEAM A
BOTTOM SUPPORT
BRACE
BRACE CAP
5 LINK SUSPENSION CHAIN
3 LINK SUSPENSION CHAIN
9 4
CHAIN CONNECTOR
1
SIDE BEAM B
1
CANOPY
2
2
WASHER D6.5*D13*1.0
BOLT M6*30
1
1
FRONT CANOPY BRACE
CANOPY CROSS BRACE
U-SHAPED CANOPY BRACE
2
ASSEMBLY INSTRUCTIONS • MODEL: 273-5112
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE. INTENDED FOR RESIDENTIAL USE ONLY.
!
• Use the correct bolts as indicated. Do not tighten any of the bolts until the hammock is completely assembled.
• Do not discard of any of the packaging until you have checked that you have all of the parts and fittings required.
• Keep children away during assembly. This item contains small parts that can be swallowed by children.
• Children should always be under direct adult supervision while using this product.
• Retain these assembly instructions for future reference.
PARTS LIST

FIGURE 1
FIGURE 2
FIGURE 3
FIGURE 4
4
4
4
4
4
4
2
2
13
11
12
10
4
4
4
4
2
11
1
14
4
4
2
4
Step 2:
Insert bolt (#10) with washer (#12) through the outside
bottom support (#4). Then, place washer (#11) onto the
bolt and insert through the inside bottom support (#4).
Place a plastic end cap (#13) onto the bolt and screw into
the cross brace (#2). Repeat the same procedure for both
sides. See Figure 2.
Note:
The labelled arrows on the bottom supports (#4) should
be facing each other as displayed in Figure 1.
Step 1:
Position two bottom supports (#4) together facing in
opposite directions. See Figure 1.
Step 3:
Secure the safety locks on all sides of the bottom
supports (#4). See Figure 3.
Step 4:
Press the spring buttons on the bottom supports (#4)
and insert into the side supports (#1). Make sure that the
spring buttons on the bottom supports (#4) come
completely through the holes on the side supports (#1).
See Figure 4.
2

FIGURE 8
FIGURE 7
FIGURE 6
FIGURE 5
3
17
1
1
1
1
16
799
5
5
6
5
14
14
7
17
17
3
Step 5:
Slide the magazine bag (#16) onto one of the side
beams A (#3). Press the spring buttons on the side
supports (#1) and insert into the side beams (#3 and #17).
Make sure that the spring buttons on the side supports
(#1) come completely through the holes on the side
beams (#3 and #17). See Figure 5.
Step 6:
Attach the 5-link suspension chains (#7) onto the chain
connectors (#9). Insert the braces (#5) into the sleeves
of the fabric (#14). Place the chain connectors (#9) onto
the braces (#5) where there are slits. See Figure 6.
Note:
Make sure that the suspension chains (#7 and #8) are
properly connected without any twists and tangles.
Step 7:
Place the brace caps (#6) onto the ends of the braces
(#5). See Figure 7.
Step 8:
Hang the 5-link suspension chains (#7) that are already
attached to the braces (#5) onto the hooks located on the
side beams (#3 and #17). See Figure 8.
3

FIGURE 9
Step 9:
Hang the 3-link suspension chains (#8) to the hooks
on one of the side beams (#17), then place pillow
(#15) onto the hammock. See Figure 9.
15
8
Note:
The 3-link suspension chains (#8) are to be used
when the hammock is folded closed.
FIGURE 10
19
23
20
FIGURE 11 FIGURE 12
Step 11:
Insert the front canopy brace(#18) into the sleeves
of the canopy (#23). See Figure 11.
Step 12:
Attach the front canopy brace (#18) to the U-shaped
canopy brace (#20). Then fasten the canopy cross
brace (#19) and front canopy brace (#18) by using
bolt (#21) and washer (#12) for both sides.
See Figure 12.
14 12
14 12
19
19
18
18
18
20
18 1820
20
18
21
22
23 20
Step 10:
Insert the canopy cross brace (#19) and U-shaped
canopy brace B (#20) into the sleeves of the canopy
(#23). See Figure 5.
FIGURE 13
17 18
18
Step 13:
Insert the front/rear canopy braces (#18) into the
side beam B (#17). See Figure 13.
4

FIGURE 11
FIGURE 10
Cleaning and Maintenance
•Wash frame parts with mild soap and water, rinse thoroughly,
and dry completely. Do not use bleach, acid, or other solvents
on the frame parts.
•Fabric and pillow may be washed on the surface only by
using mild soap and water or a commercial foaming upholstery
cleaner if necessary. If washed, rinse well and hang to dry.
Do not machine wash or dry.
•Inspect and tighten all bolts and fasteners on a regular basis
to ensure proper performance and safety of your hammock.
•In order to prolong the life and beauty of your hammock, we
recommend that it be stored in a dry and protected area
during off season periods.
Note:
Before each use, inspect the hammock to ensure that all parts
are in good order and are properly assembled. Carefully
examine the frame to ensure that all parts (including welds)
are sound (free of excessive rust or cracks). 8
Warning:
Two peope are needed to open or fold the hammock and
please hold the hammock at the top when opening or closing.
The store where you made your purchase
does not stock parts for this item. If you
need parts, whether they are missing or
damaged, Call: 1-920-487-5577.
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
For further assistance, please visit us at:
[email protected]
To Fold The Hammock:
Step 1:
Release the safety locks on the bottom supports (#4).
See Figure 10.
Step 2:
Fold the hammock and secure in place by hooking the 3-link
suspension chains (#8) to the opposite side beams (#3).
See Figure 11.
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING
ASSEMBLY.SEPARATE AND IDENTIFY ALL OF THE PARTS, MAKING
SURE THAT YOU HAVE ALL OF THE PARTS LISTED.
IF YOU DO NOT LOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTS THAT MAY HAVE BECOME
SEPARATED DURING SHIPMENT.
IF ANY PARTS ARE MISSING OR DAMAGED, CALL CUSTOMER SERVICE
AT 1-920-487-5577 BEFORE RETURNING THIS ITEM TO THE STORE.
PROVIDE THE FOLLOWING INFORMATION WHEN CALLING:
1: MODEL NUMBER OF THE PRODUCT.
2: PART NUMBER.
MOST PROBLEMS CAN BE RESOLVED WITHOUT RETURNING THIS
PRODUCT TO THE RETAILER.
5
4