Ballard Designs Trieste User manual

Prevent accidentally discarding small parts or
hardware. Retain all carton contents until assembly
and installation are complete.
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 7-19-2021 Page 1 of 4
PRODUCT NAME: Trieste 2 Door Console Cabinet
ITEM NUMBER: SK067
ASSEMBLED DIMENSIONS : 35”H x 25.75”W x 18.63”D
MADE IN INDONESIA
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Page 2 of 4
Cleaning and Care
Periodically dust with a soft, dry cloth.
Prevent finish damage: do not use alcohol based
cleaners or polishers. Promptly remove spills.
Shelf (I)
(Ships installed inside Cabinet)
(H)
MOULDING: Attach Base Moulding (H) to
lower sides of Cabinet (G). Omit when joining
multiple Cabinets. Use to cap both open ends
of a multi-cabinet unit.
SHELF: Use a Phillips Screwdriver to remove Set
Screws. Lift Shelf (I) out. Remove and reposition
Shelf Supports (J). Replace Shelf then reinsert Set
Screws. Fully tighten.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(G)
LEVELERS: Console equipped with Rotary Levelers
under each corner. To adjust, insert Slotted Screw-
driver (B) into fitting INSIDE cabinet and turn to raise
or lower corner.
(E)
(J)
(A)
Assemble in location for intended use.
Ltr.
A1
B
Qty. Hardware Included
REQUIRED TOOLS:
Phillips Screwdriver, Slotted
Screwdriver (included),
Allen Wrench (included)
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
Ltr.
G
H
1
2
Qty. Components
Cabinet (G)
Wall Anchoring
(Anti-tip) Kits
(See page 4)
2
Slotted Screwdriver
For use with Levelers. Retain with Cabinet.
Base Moulding (H)
C4
D
F2
4
Connector Plates
Allen Bolts
Flat Washers
E1Allen Wrench
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
ANCHORING HARDWARE INCLUDED
I1

Page 3 of 4
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
WARNING: To prevent a dangerous tip-over accident, Cabinets must be secured
together using Brackets as illustrated in this step.
Place Cabinets side by side. Remove Base Moulding (D) from adjoining sides. (Fig. 1) Align side and
back edges then position two Connector Plates (D) as illustrated. Secure using Allen Bolt (A) with Flat
Washer (B). (Fig. 2) Apply Base Moulding to both open ends.
NOTE: Individual Cabinets sold separately.
Fig. 1
Fig. 2
(E)
(B) (C)
(H)
Use Moulding on open ends.
Omit when joining multiple units.
N
O
T
E
(D)
- If installing optional Hutch (sold separately) please refer to Assembly Instructions included with
Hutch for properly joining all units together using Connector Plates.
- It may be easier to level multiple Cabinets AFTER they’ve been joined together using Connector
Plates.
- Anchor Single and joined Cabinets to wall using Anti-Tip Anchoring Hardware as outlined on Page 4.
- When joining multiple units, there will be leftover/surplus/unused Connector Plates, Bolts, Washers
and Base Moulding.
*PLEASE NOTE
i
*INSTRUCTIONS FOR JOINING MULTIPLE CABINETS

(C)
(B)
(D)
(A)
WALL STUD
Page 4 of 4
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
WALL BRACKET MUST BE ATTACHED TO WALL STUD
WALL ANCHORING HARDWARE (ANTI-TIP)
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
Ltr.
A4 Small Screw
Retention Belt
Qty. Hardware Included
B4 Large Screw
C4 Bracket
D2
1. Place furniture against wall at desired location then locate and mark a Wall Stud behind unit.
2. Corresponding to Stud location, attach one Bracket (C) to back of unit using Small Screws (A).
3. To keep hardware out of view after installation, attach remaining Bracket (C) INTO WALL STUD
with Large Screws (B) 2 inches below Bracket attached to back of unit.
4. Move unit into place, align Brackets then connect both using Retention Belt (D).
5. Confirm Belt is securely laced and locked.