Ballard Designs CASA Florentina Josephina Bookcase with Cabinet... User manual

PRODUCT NAME: MV430
ITEM NUMBER: Josephina Bookcase with Cabinet
ASSEMBLED DIMENSIONS: 82 1/2”H x 37 1/4”W x 15”D
PRODUCT NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 3-18-2020
MADE IN ITALY
Page 1 of 6
Customer Service : 800-367-2810
Online: www.ballarddesigns.com

Page 2 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Ltr.
A 16
B 2
Qty. Hardware Included
Ltr.
G
H
2
2
Qty. Components
C 16
REQUIRED TOOLS :
Phillips Screwdriver
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
NOTE: To avoid accidentally
discarding small parts or hardware,
retain all carton contents until
assembly and installation are complete.
Shelf Supports
Leveler Tool
Connector Brackets
(For joining 2 or more cabinets)
Screws
D
E
Anti-Tip
Anchoring Kit
8
1
I
J
4
1
Shelves (I)
Bookcase (J)
Base Molding (G)
Crown Molding (H)
F2
Bolts
WARNING
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
ANCHORING HARDWARE INCLUDED

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 3 of 6
STEP 1: Bookcase (J) is equipped with removable Base (G) and Crown Molding (H). BASE: On a
soft, padded surface gently lay Bookcase face down. Orient base molding with square edge to back
and insert Bolts (D) through pre-drilled holes and into T-nut in Base Molding. Use a screwdriver to
firmly tighten.
Install Bolts through
cabinet from inside base
(J)
(G)
(D)
Install Bolts through
cabinet from inside top
(D)
STEP 2: Stand Bookcase (J) upright and install Crown Molding (H) to upper sides. Orient Crown
Molding with square edge to back then insert Bolts (D) through pre-drilled holes in upper inside of
Bookcase and into T-nuts in molding. Use a screwdriver to firmly tighten.
(J)
(H)
(H)
(J)

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 4 of 6
STEP 3: Determine placement for Shelves (I) then insert Shelf Supports (A) into corresponding
pre-drilled holes inside Bookcase (J). Tilt in and gently lay Shelf upon Supports.
(J)
(A)
(I)
STEP 4: Bookcase (J) is equipped with Levelers under each corner which are accessible from the
bottom INSIDE of Bookcase. If necessary, insert Leveler Tool (E) into opening in corner(s) and turn
clockwise/counterclockwise to adjust. NOTE: Take care during leveling process to prevent Bookcase
from tipping over. A second person holding Bookcase is advised.
Leveler accessible from inside
Bookcase.
(J)
(J)
(E)

Cleaning & Care:
DO NOT use alcohol based products or spray polisher as they can damage the finish.
Dust with soft cloth. Finish can be affected by heat or extended contact with oils or wine.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 5 of 6
STEP 5: (OPTIONAL) Muliple Casa Florentina Josephina components (each sold separately) may be
joined together into a single unit. First, remove Crown and Base Molding (Steps 1 and 2) on sides of
units that abut one another. Push units together and use Connector Brackets (B) to join at seams on
back side. Use a screwdriver to firmly tighten Screws (C).
NOTE: Align cross imprinted into Connector Bracket directly over seam between units. This will
ensure screws are secured into wood side panels and NOT backer board.
FRONT VIEW BACK VIEW
(B) (C)

Ltr. Qty. Hardware Included
F 2
G 2
H 4
I 2
Small Screw
Large Screw
Brackets
Retention Belt
(H)
(F)
(H)
(G)
(I)
ANTI-TIP ANCHORING HARDWARE (Part F)
WALL STUD
Serious or fatal crushing injuries can occur from a furniture tip-over
WARNING
Tip-Over Hazard
WALL BRACKET MUST BE ATTACHED TO WALL STUD
Prevent tipping accidents. Anchor your furniture.
1. Locate and mark a Wall Stud behind Bookcase at location for installation.
2. Corresponding to Stud location, attach one Bracket (C) to back of Bookcase using Small Screw (B).
3. To keep hardware out of view after installation, attach remaining Bracket (C) INTO WALL STUD
with Large Screw (A) 2 inches below Bracket attached to back of Bookcase.
4. Move Bookcase into place, align Brackets then connect both using Retention Belt (D).
5. Confirm Belt is securely laced and locked.
Anti-Tip Hardware Installation
Bookcase
Wall Stud
Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 6 of 6