Ballard Designs Harper Sideboard SF038 User manual

PRODUCT NAME: Harper Sideboard
ITEM NUMBER: SF038
DIMENSIONS OF ITEM ASSEMBLED: 38”H x 66”W x 18”D
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 2-1-2022 Page 1 of 5
MADE IN INDONESIA
Prevent accidentally discarding small parts or
hardware. Retain all carton contents until assembly
and installation are complete.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Page 2 of 5
Ltr.
A4
B
Allen Bolt
Allen Wrench
1
C2
Qty. Hardware Included
Ltr.
Cabinet (D)
Base (E)
D
E 1
1
Qty. Components
Wall Anchoring
(Anti-tip) Kits
See Page 4
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
ANCHORING HARDWARE INCLUDED
Cleaning and Care
Periodically dust with a soft, dry cloth.
Prevent finish damage: do not use alcohol based
cleaners or polishers. Promptly remove spills.
TOOLS REQUIRED:
Allen Wrench (included),
Phillips Screwdriver
-Two person assembly
suggested.
Assemble in location for intended use.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Doors are factory leveled and aligned. However, if
adjustments are required refer to Page 5 for detailed
instructions regading door hinges.

ASSEMBLY: It may be helpful to lay Cabinet (D) onto its back onto a level, padded surface. Next,
align holes in top of Base (E) with embedded T-nuts in bottom of Cabinet. Insert an Allen Bolt (A) into
each hole. Fit and insert ALL Bolts before fully tightening each using Allen Wrench (B).
ADJUSTABLE SHELVES: Shelves ship pre-installed. To remove, first use a Phillips Screwdriver to
remove Set Screw from each Shelf Support. Next, carefully lift out Shelf. Reposition Shelf Supports,
replace Shelf then reinsert and tighten Set Screws.
LEVELERS: Sideboard is equipped with Rotary Levelers installed under Base. If necessary, adjust-
ments may be made by carefully lifting applicable corner and turning Leveler clockwise/counterclockwise.
Page 3 of 5
(E)
(D)
(D)
Shelf
Support
(B)
(A)
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Assemble in location for intended use.

Page 4 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(A)
(D)
(B)
(C)
W
A
LLS
T
U
D
WALL BRACKET MUST BE ATTACHED TO WALL STUD
WALL ANCHORING HARDWARE (ANTI-TIP)
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
Ltr.
A4 Small Screw
Retention Belt
Qty. Hardware Included
B4 Large Screw
C4 Bracket
D2
1. Place furniture against wall at desired location then locate and mark a Wall Stud behind unit.
2. Corresponding to Stud location, attach one Bracket (C) to back of unit using Small Screws (A).
3. To keep hardware out of view after installation, attach remaining Bracket (C) INTO WALL STUD
with Large Screws (B) 2 inches below Bracket attached to back of unit.
4. Move unit into place, align Brackets then connect both using Retention Belt (D).
5. Confirm Belt is securely laced and locked.
Representative Image
Not meant to be actual item included with
these instructions.

Page 5 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Adjusting Door Alignment
Doors shoud arrive level and aligned, however, if adjustment is necessary follow
these instructions to correct any issues.
To Correct Vertical Alignment:
Loosen Screw (A) then turn Screw (B) clock-
wise/counterclockwise to adjust door.
When alignment is achieved, retighten Screw (A).
(B)
(A)
To Correct Flush Alignment:
Loosen Screw (A) adjust door front to back as
needed.
When alignment is achieved, retighten Screw (A).
To Correct Horizontal Alignment:
Loosen both Screws (C) adjust door up or down
as needed.
When alignment is achieved, retighten both
Screws (C).
(A)
(C)
(C)
Side
View Door