Bay Tek Games Super Shot User manual

1

2
FACTORY CONTACT INFORMATION
BAY TEK GAMES INC.
Pulaski Industrial Park
1077 East. Glenbrook Drive
Pulaski, WI 54162 USA
PARTS
P: 920.822.3951 X 1101
F: 920.822.1496
E: [e-mail]
MON - FRI
8 AM - 5 PM C.S.T.
SERVICE
P: 920.822.3951 X 1102
F: 920.822.1496
E: [e-mail]
SALES
P: 920.822.3951
F: 920.822.8936
E: [e-mail]
All games are proudly manufactured at our factory in Pulaski, Wisconsin, USA
JOIN OUR SERVICE FIRST NETWORK!
This free service is intended to keep you up to date on the latest game
information, early notication of parts specials, pertinent technical
bulletins, updates on retro t parts, software upgrades, and much more.
Log on to: www.baytekgames.com/parts
then click on the Parts N’ Service tab, or scan the QR code below with
your Smartphone to jump straight to this game’s parts page!
Scan here!

3
TABLE OF CONTENTS
FACTORY CONTACT INFORMATION ........................................2
WELCOME TO: Super Shot ................................................4
HOW TO PLAY ..........................................................5
SPECIFICATIONS........................................................6
SAFETY PRECAUTIONS ..................................................6
SET UP GUIDE ....................................................... 7-17
HOW TO: INSTALL LINKING KIT ........................................ 18-20
DIP SWITCH SETTINGS .................................................21
MAIN MENU FUNCTIONS ................................................22
CREDITS PER PLAY ..............................................23
ATTRACT VOLUME ...............................................23
GAME VOLUME ..................................................23
ATTRACT TIMING.................................................24
JOIN IN TIME DELAY ..............................................24
GAME LENGTH ..................................................24
THREE POINT TIME ...............................................25
POINTS NEEDED FOR BONUS TIME .................................25
BONUS TIME REWARDED .........................................25
BONUS TIME MODE ..............................................26
POINTS PER TICKET ..............................................26
DOUBLE TICKETS ................................................26
MINIMUM TICKETS DURING GAME PLAY .............................27
JACKPOT INCREMENT ............................................27
JACKPOT DECREMENT ...........................................27
JACKPOT MINIMUM...............................................28
JACKPOT MAXIMUM ..............................................28
MINIMUM HIGH SCORE............................................29
HIGH SCORE RESET..............................................29
RESET SETTINGS ................................................29
DIAGNOSTICS .........................................................30
MAIN BOARD WIRING PIN OUT ...........................................31
WIRING DIAGRAMS.................................................. 32-35
TROUBLE SHOOTING GUIDE.......................................... 36-41
HOW TO GUIDES .................................................... 42-43
BILL ACCEPTOR DIAGNOSTICS...........................................44
POWER SUPPLY DIAGNOSTICS ..........................................45
MAINBOARD PINOUT & GUIDE ........................................ 46-47
PARTS LIST ...........................................................48
PARTS PICTURES ................................................... 49-50
OPTIONAL JACKPOT SIGN ............................................ 51-54
OPTIONAL GAME DIVIDERS........................................... 55-62
OPTIONAL SIDE SKIRTS .............................................. 63-64
MAINTENANCE LOG ....................................................65
TECHNICAL SUPPORT ..................................................66
WARRANTY ...........................................................67

4
WELCOME TO: Super Shot
Congratulations on your Super Shot purchase!
WIth it’s enhanced backboard lighting, easy-to-read time and score displays, along with
the excitement of a moving target, Super Shot is the standard in arcade basketball!
Link a bank of games together with an attractive jackpot sign to create an incredible
presence!
Please take a moment to read through this manual and be sure to contact our factory if
you have any questions, or would like some more information.
Thank you for your purchase! Your business is important to us and we hope you enjoy
this game as much as we do!
Your Friends at Bay Tek Games
GAME INSPECTION
Inspect the game for any damaged, loose, or missing parts.
If damage is found, please contact your freight carrier rst.
Then, contact Bay Tek Games’ Service Department at 920.822.3951
or e-mail them at [email protected] for further assistance.

5
HOW TO PLAY
Insert credits and select game play:
A - CLASSIC: Basket stays up front until
last part of game when it moves to rear
B - CONTINUOUS: Basket moves back
and forth throughout game play
C - PUSH BACK: Basket moves in
increments after each successful basket
D - STATIONARY: Basket is set to the
back wall and does not move
Wait for others to join for competition play.
Shoot as many balls as you can in the
alloted time and make them in the hoop to
score points!
Win tickets for points scored! Beat the
jackpot score and win the jackpot tickets!

6
GAME SPECIFICATIONS
SAFETY PRECAUTIONS
WEIGHT
NET WEIGHT 900 LBS.
SHIP WEIGHT 960 LBS.
DIMENSIONS
WIDTH 34”
DEPTH 126”
HEIGHT 108”
OPERATING TEMPERATURE
FAHRENHEIT 80-100
CELSIUS 26.7-37.8
POWER REQUIREMENTS
INPUT VOLTAGE
RANGE
100 to 120
VAC /220 to 240 VAC
INPUT FREQUENCY
RANGE 50 HZ / 60 HZ
MAX OPERATING
CURRENT
1.4 AMPS @ 115 VAC
.8 AMPS @ 230 VAC
DANGER
DO NOT perform repairs or maintenance on this game with the power ON.
Unplug the unit from the wall outlet or shut off the power strip located inside the cabinet.
!!
NOTICE
Modications to the mechanical, electrical and structural components of this game
may void its compliance certications.
!!
WARNING
Use of ammable subtances can cause sever burns or serious injury.
Always use NON-FLAMMABLE solvents for cleaning. DO NOT use gasoline kerosene or thinners.
!!
CAUTION
Lifting heavy objects can cause back, neck or other injuries. Be sure adequate lifting and moving
devices are available when unloading, unpacking and moving this game.
!!
ATTENTION
Be sure the electrical power matches the game requirements. See the serial number located on the
back of the game cabinet. Always plug into a grounded circuit. If the supply cord is damaged, it must
be replaced by an approved cord or assembly provided by the manufacturer.
A shielded power cable must be used for the game to retain EU/EMC compliance.
!!
IN CASE OF EMERGENCY
UNPLUG THE POWER CORD.
The power cord must be accessible at all times in case of an emergency.
!!
This appliance is suitable for INDOOR, DRY locations only.

7
SET UP GUIDE
Lay the clear backboard on a clean, stable
surface.
Locate the hardware kit inside the cash box.
Remove four at washers, two split washers, two
nylon nuts and two hex-bolts.
With assistance, lift the backboard piece and insert
it into the rear of the ball ramp.

8
SET UP GUIDE CONT.
The legs of the backboard will slide into the red
cut outs and rest on the pemstuds at the bottom.
On the top of the legs, secure to the red metal
cut out pieces using a at washer, a split washer
and the hexbolt - one on each side. (highlighted
in pink)
On the bottom of the legs, secure to the
pemstud using a at washer and a nylon nut -
one on each side. (highlighted in green)

9
SET UP GUIDE CONT.
Plug in the gray cables from the backboard, to the
corresponding colored housings on the gray
cables (hoop sensors) already ran on the bottom
back of the ramp.
Leaving a service loop of 16”-18”, secure the
cables to the sticky tabs already attached to the
cabinet, using the zip ties included in the
hardwarde kit.

10
SET UP GUIDE CONT.
Again with assistance, lift the “crowd”
backboard up and insert it into the rear of
the ramp, behind the clear backboard. BE
CAREFUL NOT TO PINCH THE CABLES!
Run the cables through the cut out on the
metal piece, above the ‘NOTICE’ decal.
Plug cable 7429 from the backboard into
cable 7402.

11
SET UP GUIDE CONT.
Plug ribbon cable 7419 from the backboard
into the housing located on the back,
bottom right side of the ramp.
Secure the 7429 to the sticky tab up inside
the rear of the ramp using a zip tie included
in the hardware kit.

12
SET UP GUIDE CONT.
Secure the ribbon cable to the sticky tabs
up inside the rear of the ramp using zip ties
included in the hardware kit.
**BE CAREFUL TO NOT TIGHTEN THE
ZIP TIES TOO TIGHTLY AROUND THE
RIBBON CABLE - THIS WILL CAUSE
DAMAGE TO THE CABLE!
In the front of the ramp, lift and insert the
ball stop acrylic piece.
Install so the acrylic piece sits ush with the
top of the display section.

13
SET UP GUIDE CONT.
Get four bolts and four lock washers from
the hardware kit.
Insert two bolts and two washers on each
side to secure the ball stop acrylic in place.
Tighten all bolts.
With assistance, lift the cage on top of the
ramp.
Insert the notches on the bottom of the
cage, into the cut outs in the top of ramp.

14
SET UP GUIDE CONT.
Get ten bolts from the hardware kit to
secure the cage in place.
There will be two bolts in the front of the
cage and three in the rear (circled in yellow
in the diagrams). Insert the bolts and
secure the cage.
Repeat this for both sides of the cage.
Remove the protective lm from the ball
stop acrylic.

15
SET UP GUIDE CONT.
With assistance, lift and set the console
section in front of the ramp.
Lift the console and insert the tabs on the
rear of the console, into the cut outs on the
front of the ramp.
Lift the console at the front to lock the tabs
down into the cut outs.

16
SET UP GUIDE CONT.
Inside of the ball return area, you will need
to secure the console to the ramp.
Use the bolts and lock washers from the
hardware kit. There will be a washer and
bolts inserted into each side.
Plug in the cable bundle from the console
to the cable bundle from the ramp. Each
cable will only have one match so they can
not be mixed up.
Route the ribbon cable from the ramp
through the hole on the back of the console
and down into the console.
Secure the excess ribbon cable into the
saddles on the bottom of the console.

17
SET UP GUIDE CONT.
Route the power cable through the hole on
the back of the console and down into the
console.
(The blue colored phone cable port on the
main board inside the console is where you
will link multiple games together or connect
a jackpot sign)
Inside the console, route and plug in the
power cable to the line lter box.
Route and plug in the ribbon cable to the
housing on the CB3904 circuit board.This
location is also labeled.
Plug remaining end of power cable into a
standard power outlet. You are now ready
to play ball!

18
HOW TO: INSTALL LINKING KIT
Open the linking kit box and remove the
gray phone cables.
Plug in the black power cable to the power
supply and route through the cut out in the
box on the opposite side of the door hinge.
Each game in the bank will require it’s own
phone cable. Route the needed cables
through the cut out in the black box on the
same side as the hinge for the door.

19
HOW TO: INSTALL LINKING KIT CONT.
Plug each of the phone cables into the
phone ports on the Multi-plexer board
inside the linking box.
Close the cover on the linking box when all
phone cables are plugged in.
Under the ball return ramp area, unplug all
the wire housings and use a drill to remove
the screw in the clamp that is holding the
bundle of cables up.
Move the bundle of cables to the side.
Locate the hardware kit in
the cash box with the black
10 screws inside.
Use the screws to attach
the linking box to any of the
games in the bank, under
the ball return ramp - use
the pilot holes.

20
Reconnect all of the cables that you
disconnected earlier under the ball return
ramp.
Plug the power cable from the linking box
into a standard power outlet.
Feed one phone cable from the linking box
into each of the game consoles. Insert the
phone cable through the hole cut out on
the back side of the console.
Inside the console of each game, plug the
phone cable into the blue phone port on the
main board.
HOW TO: INSTALL LINKING KIT CONT.