BEGA 84065 Manual

Installation and Technical Information
BEGA
Replacement Parts
In the interest of product improvement, BEGA reserves the right to make technical changes without notice.
BEGA 1000 Bega Way, Carpinteria, CA 93013 [phone] Fax [phone] www.bega-us.com © Copyright BEGA-US 2018
Accessories
Please refer to the appropriate
accessory installation sheet for
further instruction when applicable.
Bega-US Architectural Lighting Fixtures and Products
http://www.bega-us.com/groupimages.aspx?imagetype=gr&groupid=253&itemnoid= [9/28/2009 4:00:56 PM]











































 
Linear element - LED square 84065
Tools Required:
4mm hex key
8mm hex key
Special tool (provided)
Protection Class: IP65
Weight: 127.9 lbs.
Dimensions
A: 8-5/8” x 8-5/8”
B: 128 ”
C: 177 ”
Relamping/Maintenance
Loosen hex socket head screws near lens and
remove top. Clean luminaire and lens using only
solvent-free cleansers. Replace reector and ballast
assembly and replace top. Tighten screws evenly,
making sure gasket is seated properly.
Lamp: 39.5 W LED
84 065
3/12/2018
Page 1 of 2
Description
Lens (consult factory)
Special tool - access door
LED driver (120V-277V)
LED module (4000K)
LED module (3000K)
Part No
11318710
560091
75985-03
LED-0808/840
LED-0808/830
Anchorage Kit - included 79 801
Notice to Installer for 84 065:
1. See page 2 for specic product safety warnings.
2. 79 801 anchorage kit must be installed in concrete foundation.
3. Anchorage kit 79 801 is buried below nished grade. Attention to alignment, leveling, and
location is required for proper installation.
4. LED module and LED driver provided, integral in luminaire.
79 801 anchorage installation:
1. Provide means to bring supply wiring to linear element in accordance with local code.
The template has a 3-15/16” conduit hole for conduit entry. Provide adequate foundation
reinforcement for the intended load (by others).
2. Use template and anchor bolts provided to assemble anchorage kit to be set. Make sure
anchor bolts do not protrude from lower concrete foundation more than 3” as shown.
3. Please refer to gure to establish location of lower concrete foundation. The anchorage
kit MUST BE buried. The top of the lower concrete foundation MUST be 6-7/8” BELOW
nished grade for proper installation. Position anchorage and level template properly.
4. Align and level anchorage kit so the corners of the square template are aligned with the
desired location and orientation of the corners of the square linear element. See gure.
5. Install anchorage kit using either method:
A. Attach template to forming and level properly.
B. Insert anchorage kit into poured concrete. Concrete must be vibrated to ensure
proper anchorage setting. Level template properly.
84 065 installation:
1. Once the anchorage is set, remove template and hardware.
2. Pull supply wiring to a length where splices can be seen and made through the access
door.
3. Route supply wiring through the mounting base and install mounting base using hardware
provided. Complete nished grade. See gure.
4. Use special tool provided to unlock the access door lock and remove access door. Route
the luminaire wiring down and out the hand hold for connections to be made later.
5. Loosen (8) M10 set screws at the base of the light element and place the light element
over the mounting base. Tighten (8) M10 set screws to secure to base.
6. Make supply wiring and luminaire wiring connections inside the luminaire:
MAIN VOLTAGE SUPPLY WIRE TO BLACK LUMINAIRE WIRE
NEUTRAL (COMMON) SUPPLY WIRE TO WHITE LUMINAIRE WIRE
GREEN GROUND WIRE TO GREEN LUMINAIRE WIRE
7. Replace access door and lock.

Installation and Technical Information
BEGA
In the interest of product improvement, BEGA reserves the right to make technical changes without notice.
BEGA 1000 Bega Way, Carpinteria, CA 93013 [phone] Fax [phone] www.bega-us.com © Copyright BEGA-US 2018
Linear element - LED square 84 065
84 065
3/12/2018
Page 2 of 2
Product Safety Warnings:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
SUITABLE FOR WET LOCATIONS.
MIN 90°C SUPPLY CONDUCTORS.
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT
BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.
CONVIENT AUX EMPLACEMENTS MOUILLÉS.
LES FILS D’ALIMENTATION 90°C MIN.