Belden HIRSCHMANN OCTOPUS OS3 User manual

Installation OCTOPUS OS3
Release 03 08/2020
Technical support
https://hirschmann-support.belden.com
User Manual
Installation
Managed Ethernet Switch
OCTOPUS OS3

13.8.20 Installation OCTOPUS OS3
Release 03 08/2020
The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2020 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany

Installation OCTOPUS OS3
Release 03 08/2020 3
Contents
Important Information 6
Safety instructions 7
About this manual 13
Key 14
1 Description 15
1.1 General device description 15
1.2 Device name and product code 16
1.3 Device views 18
1.3.1 Device variants with 24 × Ethernet ports 18
1.3.2 Device variants with 16 × Ethernet ports 19
1.3.3 Device variants with 8 × Ethernet ports 20
1.3.4 Device variants with Uplink ports/Bypass function 21
1.3.5 Port assignment 22
1.4 Power supply 23
1.4.1 Supply voltage with the characteristic value BB 23
1.4.2 Supply voltage with characteristic value HH 23
1.4.3 Supply voltage with characteristic value PP 23
1.4.4 Supply voltage with the characteristic value QQ 24
1.4.5 Supply voltage with the characteristic value N9 24
1.4.6 Supply voltage with the characteristic value M9 24
1.5 Ethernet ports 25
1.6 Pin assignments 26
1.7 Display elements 28
1.7.1 Device state 28
1.7.2 Port Status 30
1.7.3 PoE status 31
1.8 Management interfaces 32
1.8.1 V.24 interface (external management) 32
1.8.2 USB interface 32
1.9 Input/output interfaces 33
1.9.1 Signal contact 33

4Installation OCTOPUS OS3
Release 03 08/2020
2 Installation 34
2.1 Checking the package contents 34
2.2 Installing and grounding the device 34
2.2.1 Mounting on a flat surface 35
2.2.2 Grounding the device 36
2.3 Connecting the ferrites 37
2.4 Connecting the supply voltage 38
2.5 Connecting data cables 39
3 Basic Settings 40
3.1 Default settings 40
3.2 First login (Password change) 41
4 Monitoring the ambient air temperature 42
5 Maintenance and service 43
6Disassembly 44
6.1 Removing the device 44
7 Technical data 45
7.1 General data 45
7.2 Supply voltage 45
7.3 Power consumption/power output 48
7.4 Signal contact 49
7.5 Climatic conditions during operation 49
7.6 Climatic conditions during storage 49
7.7 Dimension drawings 50
8 Electromagnetic compatibility (EMC) 53
9 Immunity 54
10 Network range 55
11 Scope of delivery 56

Installation OCTOPUS OS3
Release 03 08/2020 5
12 Accessories 57
13 Underlying technical standards 58
A Further support 59

6Installation OCTOPUS OS3
Release 03 08/2020
Important Information
Notice: Read these instructions carefully, and look at the equipment to
become familiar with the device before trying to install, operate, or maintain
it. The following special messages may appear throughout this
documentation or on the equipment. The message warns of potential
hazards or calls attention to information that clarifies or simplifies a
procedure.
Symbol explanation
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow
this symbol to avoid possible injury or death.
The additional of this symbol to a “Danger” or “Warning” safety
label indicates that an electrical hazard exists, which will result
in personal injury if the instructions are not followed.
This symbol points out the dangers posed by hot device
surfaces. In connection with safety notes, the disregard of these
instructions will result in injury.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided,
can result in death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided,
can result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to physical injury.

Installation OCTOPUS OS3
Release 03 08/2020 7
Safety instructions
General safety instructions
You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance procedures.
Before connecting any cable, read this document, and the safety
instructions and warnings.
Operate the device with undamaged components exclusively.
The device is free of any service components. In case of a damaged
or malfunctioning device, turn off the supply voltage and return the
device to Hirschmann for inspection.
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
Certified usage
Use the product only for the application cases described in the
Hirschmann product information, including this manual.
Operate the product only according to the technical specifications.
See “Technical data” on page 45.
Connect to the product only components suitable for the requirements
of the specific application case.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

8Installation OCTOPUS OS3
Release 03 08/2020
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.
Qualified personnel are aware of the dangers that exist in their work.
Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.
Installation site requirements
Verify that there is at least 4 in (10 cm) of space above and below the
device.
Install this device solely in an operating site with restricted access, to
which maintenance staff have exclusive access. Install the device in
such a way that it is protected against mechanical forces in the area of
the power supply.
Exclusively install the device indoors.
Exclusively mount the device on a suitable flat metal surface to ensure
adequate cooling of the device.
Device casing
Only technicians authorized by the manufacturer are permitted to open
the casing.
Never insert pointed objects (narrow screwdrivers, wires, etc.) into the
device or into the connection terminals for electric conductors. Do not
touch the connection terminals.
Keep the cooling fins free to ensure good air circulation.
The surfaces of the device housing may become hot. Avoid touching
the device while it is operating.
Devices starting with serial number 942258...0003..... are suitable for
degree of protection IP65/67.
You find the serial number of your device on the device label on top of
the device.
To sustain the IP65/67 suitability for your device, seal all unused
connections and ports with the provided plastic protection screws. See
“Scope of delivery” on page 56. See “Accessories” on page 57 in case
of an additional demand.
To sustain the IP65/67 suitability for your device, exclusively connect
components with degree of protection IP65/67.
The torque for tightening the protection screws on the device is 5.3 lb-
in (0.6 Nm).
For the operation according to EN 45545-2 HL3: Seal all unused
connections exclusively with metal protection screws and plugs. The

Installation OCTOPUS OS3
Release 03 08/2020 9
use of plastic protection screws is prohibited.
Protection screws and screw caps made of metal are available as an
accessory.
See “Accessories” on page 57.
Grounding the device
Grounding the device is by means of a separate ground connection on the
device.
Ground the device before connecting any other cables.
Disconnect the grounding only after disconnecting all other cables.
The overall shield of a connected power supply cable is connected to the
ground connection on the metal casing as a conductor.
Requirements for connecting electrical wires
Before connecting the electrical wires, always verify that the
requirements listed are complied with.
General requirements for connecting electrical wires
The following requirements apply without restrictions:
The electrical wires are voltage-free.
The cables used are permitted for the temperature range of the application case.
Relevant for North America:
Exclusively use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire.
Requirements for connecting the signal contact
The following requirements apply without restrictions:
The connected voltage complies with the requirements for a safety extra-low voltage
(SELV) or ES1 as per IEC/EN 62368-1.
The connected voltage is limited by a current limitation device or a fuse.
Observe the electrical threshold values for the signal contact.
See “General data” on page 45.

10 Installation OCTOPUS OS3
Release 03 08/2020
Requirements for connecting the supply voltage
The following requirements apply without restrictions:
All of the following requirements are complied with:
The supply voltage corresponds to the voltage specified on the type plate of the device.
The power supply conforms to overvoltage category I or II.
The power supply has an easily accessible disconnecting device (for example a switch or
a plug). This disconnecting device is clearly identified. So in the case of an emergency, it is
clear which disconnecting device belongs to which power supply cable.
The wire diameter of the power supply cable is at least 1 mm² (North America: AWG16) on
the supply voltage input.
Exclusively applies to device variants featuring supply voltage with characteristic value PP:
The supply voltage inputs are designed for operation with safety extra-low voltage. Connect
only SELV circuits with voltage restrictions in line with IEC/EN 60950-1 to the supply voltage
connections.
Make sure that the connected supply voltage complies the requirements of IEEE 802.3af or
IEEE 802.3at:
For the use of type-1-powered devices (PoE):
Rated voltage: 48 V DC
Max. voltage range: 45 V DC ... 57 V DC
For the use of Type 2 Powered Devices (PoE+):
Rated voltage: 54 V DC
Max. voltage range: 51 V DC ... 57 V DC
The power supply is potential-free. For power supply modules capable of PoE,
exclusively use a potential-free SELV power supply.
The following requirements apply alternatively:
Relevant when the
device is supplied via 1
voltage input:
Relevant for North America:
The power supply complies with the requirements according to
NEC Class 2.
Relevant when the
device is supplied via 2
voltage inputs:
Relevant for North America:
The total voltage supply complies with the requirements as per
NEC Class 2.
Exclusively for device variants featuring supply voltage with characteristic value BB, FF,
HH, QQ:
The power supply cable is suitable for the voltage, the current and the physical load.
Hirschmann recommends a wire diameter of 0.5 mm² to 0.75 mm² (AWG20 up to AWG18).
The following requirements are alternatively complied with:
Alternative 1 The power supply complies with the requirements for a limited power source
(LPS) as per IEC/EN 60950-1 or IEC/EN 62368-1.
Alternative 2 Relevant for North America:
The power supply complies with the requirements according to NEC Class 2.
Alternative 3 All of the following requirements are complied with:
The power supply complies with the requirements for a safety extra-low
voltage (SELV) or ES1 as per IEC/EN 62368-1.
A fuse suitable for DC voltage is located in the plus conductor of the power
supply.
The minus conductor is on ground potential. Otherwise, a fuse is also located
in the minus conductor.
Regarding the properties of this fuse:
See “Supply voltage” on page 45.

Installation OCTOPUS OS3
Release 03 08/2020 11
CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):
2011/65/EU and 2015/863/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.
2014/30/EU (EMC)
Directive of the European Parliament and of the Council on the
harmonisation of the laws of the Member States relating to
electromagnetic compatibility.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
www.hirschmann.com
The device can be used in the industrial sector.
Interference immunity: EN 61000-6-2
Emitted interference: EN 55032
Safety: EN 62368-1
You find more information on technical standards here:
See “Technical data” on page 45.
Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take
appropriate measures.
Note: The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.

12 Installation OCTOPUS OS3
Release 03 08/2020
FCC note
Supplier's Declaration of Conformity
47 CFR § 2.1077 Compliance Information
OCTOPUS OS3
U.S. Contact Information
Belden – St. Louis
1 N. Brentwood Blvd. 15th Floor
St. Louis, Missouri 63105, United States
Phone: [phone]
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
Recycling note
After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.

Installation OCTOPUS OS3
Release 03 08/2020 13
About this manual
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
Documentation mentioned in the “User Manual Installation” that is not
supplied with your device as a printout can be found as PDF files for
downloading on the Internet at: https://www.doc.hirschmann.com

14 Installation OCTOPUS OS3
Release 03 08/2020
Key
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading

Installation OCTOPUS OS3
Release 03 08/2020 15
1 Description
1.1 General device description
The device is designed for the special requirements of industrial automation.
The device meets the relevant industry standards, provides very high
operational reliability, even under extreme conditions, and also long-term
reliability and flexibility.
The device allows you to set up switched Industrial Ethernet networks
according to standard IEEE 802.3.
The device works without a fan.
The device provides you with a large range of functions, which the manuals
for the operating software inform you about. You find these manuals as PDF
files on the Internet at http://www.doc.hirschmann.com
The Hirschmann network components help you ensure continuous
communication across all levels of the company.
The Network Management Software Industrial HiVision provides you with
options for smooth configuration and monitoring. You find further information
on the Internet at the Hirschmann product pages:
http://www.hirschmann.com/en/QR/INET-Industrial-HiVision
There are convenient options for managing the device. Manage your devices
via:
Network management software (for example Industrial HiVision)
Web browser
V.24 interface (locally on the device)
SSH
Telnet

16 Installation OCTOPUS OS3
Release 03 08/2020
1.2 Device name and product code
The product code is made up of characteristics with defined positions. The
characteristic values stand for specific product properties.
Item Characteristic Characteri
stic value
Description
1 ... 3 Product OS3 OCTOPUS OS3
4 (hyphen) -
5 Data rate 3 10/100 Mbit/s ports
10/100/1000 Mbit/s ports
4 10/100/1000 Mbit/s ports
6 Hardware type 0 Standard
4 Suitable for PoE or PoE+
7 (hyphen) -
8 ... 9 Total number:
PoE/PoE+ ports
00 0 × PoE/PoE+ ports
08 8 ×
16 16 ×
24 24 ×
10 ... 11 Number:
10a/100 Mbit/s PoE/
PoE+ ports
00 0 × 10/100 Mbit/s PoE/PoE+ ports
08 8 × 10/100 Mbit/s PoE/PoE+ ports
16 16 × 10/100 Mbit/s PoE/PoE+ ports
12 ... 13 Number:
10a/100/1000 Mbit/s
PoE/PoE+ ports
00 0 × 10/100/1000 Mbit/s PoE/PoE+ ports
08 8 × 10/100/1000 Mbit/s PoE/PoE+ ports
16 16 × 10/100/1000 Mbit/s PoE/PoE+ ports
24 24 × 10/100/1000 Mbit/s PoE/PoE+ ports
14 ... 15 Number:
10a/100 Mbit/s ports
00 0 × 10/100 Mbit/s ports
08 8 × 10/100 Mbit/s ports
16 16 × 10/100 Mbit/s ports
16 ... 17 Number:
10a/100/1000 Mbit/s
ports
08 8 × 10/100/1000 Mbit/s ports
16 16 × 10/100/1000 Mbit/s ports
24 24 × 10/100/1000 Mbit/s ports
18 ... 19 Number:
Ports >1000 Mbit/s
00 0 × 10000 Mbit/s ports
20 ... 21 First uplink port pair T6 2 × 1GE M12 “X”-coded
R6 2 × 1GE M12 “X”-coded, with Bypass relay
22 ... 23 Second uplink port
pair
T6 2 × 1GE M12 “X”-coded
R6 2 × 1GE M12 “X”-coded, with Bypass relay
24 (hyphen) -
25 Temperature range V Standard -40 °F ... +140 °F
(-40 °C ... +60 °C)
T Extended -40 °F ... +158 °F
(-40 °C ... +70 °C)
Table 1: Device name and product code

Installation OCTOPUS OS3
Release 03 08/2020 17
26 ... 27 Supply voltage BB 2 voltage inputs for redundant power supply
Rated voltage 24 V DC
Rated voltage range 16.8 V DC ... 32 V DC
Connection type 5-pin M12 connector
HH 2 voltage inputs for redundant power supply
Rated voltage 36 V DC ... 48 V DC
Rated voltage range 25.2 V DC ... 60 V DC
Connection type 5-pin M12 connector
PP 2 voltage inputs for redundant power supply
PoE
Rated voltage
48 V DC
PoE+
Rated voltage
54 V DC
Connection type 5-pin M12 connector
QQ 2 voltage inputs for redundant power supply
Rated voltage 24/36/48 V DC
Rated voltage range 16.8 V DC ... 60 V DC
Connection type 5-pin M12 connector
M9 Rated voltage 110 V AC ... 230 V AC,
50 Hz ... 60 Hz
Rated voltage range 88 V AC ... 265 V AC,
47 Hz ... 63 Hz
Connection type 5-pin M12 connector
N9 Rated voltage 72 V DC ... 110 V DC
Rated voltage range 50.4 V DC ... 138 V DC
Connection type 5-pin M12 connector
28 ... 29 Certificates and
declarations
Z9 CE, FCC, EN 61131, EN 62368-1
Y9 Z9 + cUL 61010
S9 Z9 + EN 50121-4 + EN 50155
30 ... 31 Software packages 99 Reserved
UR Unicast Routing
MR Unicast + Multicast Routing
32 ... 33 Customer-specific
version
HH Hirschmann standard
34 Hardware
configuration
S Standard
35 Software
configuration
E Entry (Hirschmann Standard)
B Diagnostic User (BDEW)
I Ethernet/IP
P PROFINET/IO
36 ... 37 Software level 2A HiOS Layer 2 Advanced
3A HiOS Layer 3 Advanced
38 ... 42 Software version 08.0. Software version 08.0.
XX.X Current software version
43 ... 44 Maintenance
version
00 Maintenance version 00
XX Current maintenance version
Item Characteristic Characteri
stic value
Description
Table 1: Device name and product code

18 Installation OCTOPUS OS3
Release 03 08/2020
1.3 Device views
1.3.1 Device variants with 24 × Ethernet ports
1 V.24 interface 4-pin, “A”-coded M12 socket
2 USB interface 5-pin, “A”-coded M12 socket
3 Signal contact 5-pin, “A”-coded M12 plug
4 Supply voltage connection 5-pin, “K”- or “L”-coded M12 plug
5 LED display elements for port status
6 24 × 10/100/1000 Mbit/s twisted pair port
or
10/100 Mbit/s twisted pair port
Device variants: OS3-3x...
8-pin, “X”-coded M12 socket
or
4-pin, “D”-coded M12 socket
Device variants: OS3-4x...
8-pin, “X”-coded M12 socket
7 Slot hole for mounting on a flat surface
8 LED display elements for device status
9 Ground connection
10 Ground connection (alternatively)
Table 2: Front view (using the example OCTOPUS3-40-...)
1 2 3 4
6
5
9
10
8 7

Installation OCTOPUS OS3
Release 03 08/2020 19
1.3.2 Device variants with 16 × Ethernet ports
1 V.24 interface 4-pin, “A”-coded M12 socket
2 USB interface 5-pin, “A”-coded M12 socket
3 Signal contact 5-pin, “A”-coded M12 plug
4 Supply voltage connection 5-pin, “K”- or “L”-coded M12 plug
5 LED display elements for port status
6 16 × 10/100/1000 Mbit/s twisted pair port
or
10/100 Mbit/s twisted pair port
Device variants: OS3-3x...
8-pin, “X”-coded M12 socket
or
4-pin, “D”-coded M12 socket
Device variants: OS3-4x...
8-pin, “X”-coded M12 socket
7 Slot hole for mounting on a flat surface
8 LED display elements for device status
9 Ground connection
10 Ground connection (alternatively)
Table 3: Front view (using the example OCTOPUS3-40-...)
1 2 3 4
6
5
9
10
8 7

20 Installation OCTOPUS OS3
Release 03 08/2020
1.3.3 Device variants with 8 × Ethernet ports
1 V.24 interface 4-pin, “A”-coded M12 socket
2 USB interface 5-pin, “A”-coded M12 socket
3 Signal contact 5-pin, “A”-coded M12 plug
4 Supply voltage connection 5-pin, “K”- or “L”-coded M12 plug
5 LED display elements for port status
6 8 × 10/100/1000 Mbit/s twisted pair port
or
10/100 Mbit/s twisted pair port
Device variants: OS3-3x...
8-pin, “X”-coded M12 socket
or
4-pin, “D”-coded M12 socket
Device variants: OS3-4x...
8-pin, “X”-coded M12 socket
7 Slot hole for mounting on a flat surface
8 LED display elements for device status
9 Ground connection
10 Ground
connection
(alternatively)
Table 4: Front view (using the example OCTOPUS3-40-...)
1 2 3 4
6
5
9
10
8 7