Benthin RR36 User manual

Electrical Installation
Maintenance
Electrical Installation
The motor system is maintenance-free.
The motor may only be
supplied by extra-low
voltage safety power supplies.
230 V 24 V
WARNING
Installation work in the 230 V range must only
be carried out by authorised specialists.
∆ ∆
Trans-
former
Roman blind type RR36
(24 V Motor)
Please read this intructions carefully
before fitting the blind
Installation work in the 230 V range
must only be carried out by authorized specialist.
Wrong installation may result in accidents.
Alterations of the blind must be approved by the blind manufacturer.
Keep remote controls out of the reach of children!
Dear Customer,
With this motorised roman blind system you have chosen a system that
offers innovation, high quality, and comfort, with remote control and
switch/push button options available to guarantee your satisfaction system
Your roman blind Manufacturer
© 2013 Benthin®.Misprints, errors and changes excepted . Version 02-09-2013 .97000208
Connecting example
Antrieb
M1
2
+
-
Motor
24 V DC
Antenne
SOMFY
Funkempfänger
Modul DC RTS
2 x 0,52
L1 NPE
Netz
230 V / 50 Hz
Abzw.-
Dose
230 V / 24 V
Transformator
- +
24 V DC
rt
sw
sw
sw
Single control
with wireless wall transmitter or wireless hand transmitter
Wireless receiver
D
2 ×0,75²
1-channel wireless
hand transmitter
Telis 1 RTS
5-channel wireless
hand transmitter
Telis 4 RTS
Wireless
wall transmitter
Centralis RTS
Wireless
program time control
Chronis RTS
Transformer
Transformer
Power supply
230V / 50 Hz
24V DC
Antrieb
+(-) -(+)
M
L1
N
PE
Netz
230 V / 50 Hz
Abzw.-
Dose
230 V / 24 V DC / 0,7 A
L
M
N
Schalternetzteil
Single control
with switch with integrated power pack
Connecting example
D
2 ×0,75²
Power
supply
230V / 50 Hz Switch
24V DC
Detailed information you can get from your specialist dealer
on inquiry.
Conduit
box
Conduit
box
Switch with integrated
power pack
Power supply
Power supply
Motor
Motor
Wireless receiver
Modul DC RTS
Antenna
red
black
black black

Installing the Roman blind Adjusting stop position Adjusting stop position
Install the RR36 Roman blind as described in
"Installation - Operation - Care", Roman blind type RR31.
Note: As there are so many options for controlling and
operating the Roman blind, please following the
connection and operating instructions for the SOMFY
components supplied.
Moving fabric stack to desired position
Move the fabric stack to the desired stop position (top or bottom, as
required) by operating the switch or wireless remote control, then
press the stop button.
Your Roman blind has been set up at the factory
to switch off automatically in both bottom and top
stop position.
Please make sure that the polarity of the drive mechanism is
correct or the following spindle lock adjustments (left/right)
will be reversed!
Only correct stop position if necessary! Changing the stop posi-
tion can have adverse effects and should therefore be done by
a specialist!
Adjusting stop position
Detaching fabric stack from profile
Detach the fabric stack by pulling the loop tape sideways off the
hook profile.
Adjusting top stop position
NB: For top stop position only change the position of
the first adjusting nut, which is closer to the end stop.
It may be on the left or right. The second adjusting nut
is for bottom stop position.
Undo the Allen screws at the first adjusting nut (1) and slide the nut
to the spindle lock's end stop (2). Tighten the screws back up (3).
Removing cassette
To remove the cassette, pull it forwards off the cassette holder (1)
and unhook from the profile at the top (2).
cassette holder
cassette
1
2
cassette
1
1
2
2
spindle blocking device
first adjusting nut
Reattaching fabric stack
Reattach the fabric stack to the hook profile with the loop tape.
1
2
3
Adjusting bottom stop position
NB: For bottom stop position only change the position of
the second adjusting nut! The first adjusting nut is for
top stop position.
Undo the Allen screws at the second adjusting nut (1) and slide the
nut to the spindle lock's end stop (2). Tighten the screws back up (3).
spindle blocking
device
second adjusting nut
1
2
3
Fitting cassette
To fit the cassette, place it on top of the profile (1) and press onto
the cassette holder (2).
1
1
2
2
2
1
End stop
End stop