BestScope BS-6020DRF User manual

0
Metallurgical Motorized Microscope
With Auto-Focus System
BS-6020DRF/DTRF
User Manual
It is recommended strongly that you study this manual thoroughly before using the microscope. Retain
this manual in an easily accessible place near the work desk for future reference.

1
Contents
User Notice ………………………………………………………… 2
1. Components …………………………………………………… 4
2. Assembly ……………………………………………………… 6
3. Adjustment ……………………………………………………… 1 5
4. O bservation Steps ……………………………………………… 1 6
5. Adjustment Operation ………………………………………… 1 7
6. Control Box Menu Setting ……………………………………… 2 4
7. Observation Methods ………………………………………… 2 7
8. Specification …………………………………………………… 2 9
9. Troubleshooting Guide …………………………………………… 30
Contents
Contents
Contents
Contents

2
User Notice
Ⅰ.
.
.
. Safety
Safety
Safety
Safety note
note
note
note
Ⅱ.
.
.
. Maintenance
Maintenance
Maintenance
Maintenance
User
User
User
User Notice
Notice
Notice
Notice
1. Carefully open the box, avoid the accessories, like lens, dropping to ground and being
damaged.
2. Do keep the instrument out of direct sunlight, high temperature or humidity, dusty and
easy shaking environment. Make sure the stage is smooth, horizontal and firm enough.
3. When moving the instrument, please use two hands to grip with the two sides of the
microscope body.
4. When running, the lamp house and nearby parts will be very hot. Please ensure there is
enough cooling room for them.
5. Make sure the instrument is earthed, to avoid lighting strike.
6. For safety, be sure the main switch is in “ O ” (off) state before replace the halogen lamp or
the fuse, then cut off the power, and do the operation after the lamp bulb and the lamp
house completely cool.
7. Use the factory supplied power cord, please.
The microscope has been adjusted at the factory according to the standard slide,
and all components are in the right initial position. If you want to use non-standard slide,
please refer to Chapter 6, "Control Box Menu setting ", and section 6-2-6 to re-adjust.
Otherwise, it will have serious consequences.
1. All the lenses have been well checked and adjusted. It is forbidden to disassemble them
yourself.
2. The nosepiece and coarse/fine focus unit have a compact and precise frame, please
don ’ t disassemble them as possible as you can.
3. Keep the instrument clean, wipe dust regularly, and be attention to avoid
contaminating the optical elements especially.
4. The contaminations on the prism, as finger mark and oil, could be gently wiped with a
piece of soft cloth or tissue paper, gauze which has been immersed in pure alcohol or
xylene. (
(
(
( N
N
N
N ote
ote
ote
ote that
that
that
that the
the
the
the alcohol
alcohol
alcohol
alcohol and
and
and
and the
the
the
the xylene
xylene
xylene
xylene are
are
are
are all
all
all
all burned
burned
burned
burned easily,
easily,
easily,
easily, do
do
do
do not
not
not
not let
let
let
let them
them
them
them
near
near
near
near the
the
the
the fire,
fire,
fire,
fire, and
and
and
and use
use
use
use them
them
them
them in
in
in
in a
a
a
a drafty
drafty
drafty
drafty room
room
room
room as
as
as
as possible
possible
possible
possible as
as
as
as you
you
you
you can.)
can.)
can.)
can.)
5. Don ’ t use organic solvent to wipe the non-optical elements, when you need to clean,
use the soft detergent, please.

3
Ⅲ
.
.
.
. Warning
Warning
Warning
Warning symbols
symbols
symbols
symbols
s
s
s
s ymbols
ymbols
ymbols
ymbols meaning
meaning
meaning
meaning
S urface is hot, not touch with bare hands
C arefully read the user manual b efore use . Improper use may cause personal
injury or microscope damage .
M ain Switch on
Main Switch off
6. When using, if the microscope is splash by liquid, cut off the power at once, and wipe
up the moisture.
7. Do not disassemble any parts of the microscope. That will affect the function or decline
the performance of the microscope.
8. Place the instrument in a cool, dry position. After using the microscope, remember to
cover it with dust helmet. Do wait for the lamp house cooling completely before cover.

4
1. Components
. Name Of Components
滤色片插槽
（从左侧插入）
目镜
ND 滤色片拉杆
显微镜主体
Lead
电动转换器
电源开关
聚光器
反光镜选择杆
Front View
Camera
Video Adapter
E yepiece(Ocular)
ND Filter Lever
Mirror Selector Lever
Motorized Nosepiece
Lead Screw Stage
Condenser
MainBoday
Lamp House
Light Path Selector Lever
Filter Insertion Slot (The filter
should be inserted from the
left)
Aperture Diaphragm Lever
Field Diaphragm Lever
Ploarizer Insertion Slot
Analyzer Insertion Slot
Control Box
Main Switch
1.
1.
1.
1. Components
Components
Components
Components
视频接口 (另一接口在
Video Inter
灯室
电源接口
Communication Interface(Serial port)
Communication Interface( Parallel Port )
P latform Communication Interface
Computer
Communication
Interface
Power Outlet
Power Switch
Communication Interface(Serial port)
Communication Interface(Parallel Port)
Platform Communication Interface
Lamp House
Lamp Connector
Power Outlet
Video Interface(RCA)
Video Interface (Another
Interface on the side)
Lamp House
Rear View

5
1.
1.
1.
1. Name
Name
Name
Name Of
Of
Of
Of Components
Components
Components
Components
①Display Panel: Displays the current status of the platform and the information ofthe
microscope System , the current platform position, lens position and the system brightness.
When insert the system setting status, it displays system setup parameters.
②Z-axis Lift Wheel: roll the wheel to control the Lead screw platform toup and down
(Z-axis Movement).
③Platform Control TouchPad: Use your fingertip moving on the Touchpad. Simultaneously,
the Microscope stage will be moving as your fingertip do ing (X-axis and Y - axis movement).
④Brightness A djust Button: Adjust the brightness.
⑤Z-axis Lift button: Z-axis's up and down .
⑥Objectives Change Button: C hange the objectives at clockwise or counter clockwise
⑦Auto-Focus Button: Focus automatically once.
⑧Real-time Focus Button: Control the real-time focus control function ON or OFF. I f ON ,
when m oving specimens, microscope automatically focuses the specimens all the whole
time.
⑨RTF Status Indicator: Displays the current state of real-time focus function.
⑩Function Buttons: Menu settings buttons.
Control Panel
①Display Panel
②Z-axis Lift Wheel
③Platform Control
TouchPad
④Brightness
Adjust Button
⑩Function Buttons
⑧Real-Focus Button
⑨RTF Status Indicator
⑦Auto-Focus Button
⑤Z-axis Lift Button
⑥Objectives Chage Button
LUM
LUM
LUM
LUM ZAxis
ZAxis
ZAxis
ZAxis ObJ
ObJ
ObJ
ObJ
OK
OK
OK
OK Cancel
Cancel
Cancel
Cancel
RTF
RTF
RTF
RTF
AF
AF
AF
AF
○
RTF OFF
●RTF ON

6
2.
2.
2.
2. Assembly
Assembly
Assembly
Assembly
2.1 Assembly Diagram
2
2
2
2 .
.
.
. Assembly
Assembly
Assembly
Assembly
2.1 Assembly Diagram
Stage Support Device
Main Body
Lamp House 2
Lamp House1
Specimen(Slice)
Holder
Lead Screw Platform
(Stage)
Objectives
Eyepieces
Camera
Video Adapter
Trinocular
Viewing
Unit
The following figure shows the installation sequence of the components. The number in the
figure shows the assembly steps.
�
Before installing, be sure every components is clean, do not score any parts or glass
surface.
�
Keep well with hexagon wrench provided. When replacing the components, you will need it
again.

7
2. 2 Assembly Step
Fig.1
F ig.2
2
2
2
2 .
.
.
. Assembly
Assembly
Assembly
Assembly
2. 2 Assembly Step
2.2.1 Installing Stage Support Device
Before installing the device, be sure to adjust
the coarse focus knob. Make the guide board
(see figure 1)down to the limit position, so you
can install the mechanical stage support device
easily.
Hold on the stage support device (figure 2),
place it from the top of the guide board (figure 1),
let the device (figure2) falling free until it reach
the limit position. Use the hexagon wrench to
screw down the screw and locking block , make
the stage support device (figure1) and the guide
board fixed together. (See figure 3)
Fig.3
Attention
Attention
Attention
Attention ：The
The
The
The stage
stage
stage
stage support
support
support
support device
device
device
device
must
must
must
must be
be
be
be installed
installed
installed
installed to
to
to
to the
the
the
the limit
limit
limit
limit position,
position,
position,
position,
otherwise,
otherwise,
otherwise,
otherwise, when
when
when
when the
the
the
the controller
controller
controller
controller initializing,the
initializing,the
initializing,the
initializing,the
objectives
objectives
objectives
objectives will
will
will
will hit
hit
hit
hit the
the
the
the device
device
device
device and
and
and
and be
be
be
be damaged
damaged
damaged
damaged
badly.
badly.
badly.
badly.
Attention:
Attention:
Attention:
Attention: The
The
The
The lead
lead
lead
lead Screw
Screw
Screw
Screw platform
platform
platform
platform
and
and
and
and the
the
the
the stage
stage
stage
stage support
support
support
support device
device
device
device have
have
have
have been
been
been
been
adjusted
adjusted
adjusted
adjusted horizontally
horizontally
horizontally
horizontally and
and
and
and fixed
fixed
fixed
fixed together
together
together
together
before
before
before
before leaving
leaving
leaving
leaving factory.
factory.
factory.
factory. Please
Please
Please
Please don
don
don
don ’
’
’
’ t
t
t
t
disassembly
disassembly
disassembly
disassembly it
it
it
it unless
unless
unless
unless necessary,
necessary,
necessary,
necessary, otherwse,
otherwse,
otherwse,
otherwse, it
it
it
it
will
will
will
will affect
affect
affect
affect the
the
the
the observation
observation
observation
observation precision
precision
precision
precision of
of
of
of the
the
the
the
microscopy.
microscopy.
microscopy.
microscopy.

8
2
2
2
2 .
.
.
. Assembly
Assembly
Assembly
Assembly
F ig.4
Fig.5
F ig.6
2. 2 Assembly Step
2.2. 2 Installing the reflected light brightfield /
darkfield illuminatior
⑥
2.2. 3 Installing the Trinoclar Viewing Unit
⑧
⑦
Installing the reflected light illuminator (fig.4)
on the head of microscope body (fig.5), and turn
to a proper position, then screw down the bolt ⑥
to fix it .
1. Loosen the fixed bolt ⑦on the microscope
main body, but do not let it ⑦fall out.
2. Insert the trinocular viewing unit into the
microscope head(fig.6), turn to a proper position,
let the two eyepiece tubes toward the front, then
use the hexagon wrench screw down the fixed
bolt ⑦to fix( See fig.6).

9
2
2
2
2 .
.
.
. Assembly
Assembly
Assembly
Assembly
F ig.9
F ig.8
F ig.7
2. 2 Assembly Step
2.2. 4 Installing the Lamp House
①
②
④③
Installing
Installing
Installing
Installing the
the
the
the Lamp
Lamp
Lamp
Lamp House
House
House
House 1
1
1
1 (indecent
(indecent
(indecent
(indecent light
light
light
light
illuminator)
illuminator)
illuminator)
illuminator)
1. 1. Pushing the lamp holder (Fig.7)into the
illumination kits(Fig. 6) gently until they are
against each other, turn to a proper position, then
screw down the bolt (Fig.6 ⑧) to fix it.
2. Insert the power plug (Fig.7 ①) into the power
jack of the microscope (F i g.9 ③) , and screw
down the bolt to fix it. The result in show in Fig.
10 .
Installing
Installing
Installing
Installing the
the
the
the Lamp
Lamp
Lamp
Lamp House
House
House
House 2
2
2
2 (transmitted
(transmitted
(transmitted
(transmitted light
light
light
light
illuminator)
illuminator)
illuminator)
illuminator)
2. 1. Pushing the lamp holder (Fig. 8 ②)into the
illumination kits , gently until they are against each
other, turn to a proper position, then screw down
the bolt to fix it.
2. Insert the power plug ( Fig. 8 ②) into the power
jack of the microscope (F i g.9 ④) , and screw
down the bolt to fix it. The result in show in Fig.
10 .