BFT Maxima Ultra 36 User manual

Maxima Ultra 36 QRG
Quick referance guides are not replacements for the supplied Instructions, they are
supplementary.
Read and understand the Installer warnings in the main Instruction document first.
Always apply good, safe, state of the art engineering and electrical Installation priciples.
Safety of the completed Installation is the ultimate responisiblity of the Installer.
This product is not suitable for DIY use and should only be Installed and maintained by a
Trained, Skilled, Professional Installer.

Cabinet/Boom Selection
One boom to cover from 2m up to 6m openings
Boom PS: boom with GOM rubber & Top Perspex cover
Boom PS: as above with ADJ-Foot (swinging leg)
Boom PS: BTM-SKIRT & Top Perspex cover
Boom PS: BTM-SKIRT+ADJ-FOOT & Top Perspex cover
Hyphen PS: to be used with XL Version
RG LED lights can be fitted to all Boom lengths
XL Version
Two cabinet bodies are available: MU36 & MU36XL
See chart below for configuration of both MU36 & MU36XL
Standard
Version

Barrier Dimensions & Handing
Left Hand
Right Hand

Installing The Cabinet

Omega Boom Flange and Boom Holder
1
2 3
4
5
6
7
8
9
10

Step 1 Boom Flange (omega)
Fit the boom flange to the output shaft on the chosen side of the cabinet
using the components 1, 2, 3 & 4. Don’t forget to remove the plug in the
output shaft for the LED lighting kit cable if being fitted.
The output shaft will be in the open
position from factory.
Ensure Roll
Pin is fitted
3
M14 = 22mm Socket
Wrench

Step 2 Spring Position
The spring arm has 3 positions to suite the boom length. From the factory
the fixing hole 2 is used on the MU36 and fixing hole 3 on the MU36XL so
repositioning maybe required depending on the boom length. Example
below shows a Boom PS at 5.5m long, hole 3.
This procedure is carried out with the spring out of compression and is
accessed via the back of the cabinet.
19mm

Step 3 Boom Lights
Once the boom flange is in position feed the black 3 core cable on the LED
strip through from the back of the flange and through the groove in the output
shaft into the cabinet.
The cable from point A to point B
= 420mm
A
B

Step 4 Boom Fitting
Remove the GOM rubber profile & Top LED Lens cover from the boom.
Fit the boom arm holder 5onto the end of the boom and bring the boom to the flange
and fit 1 nut and bolt 6as shown in fig 2.
Once the nut & bolt shown has been fitted lift the boom to the vertical position and fit
the remaining 3 nuts & bolts 6. Longer boom lengths may require two people to lift the
boom to the vertical position. Do not over tighten the 4 nuts & bolts at this stage.
If working on the XL model then don’t forget to insert the HYPHEN reinforcement
before attaching the boom to the flange.

Step 5 Power Up
Ensure the boom is in the vertical position.
1, Remove protective cover of the internal CSB Xtream control unit.
2, Route cable’s up through the back of the cabinet and terminate
the power cord to the control board.
3, Apply power and let the panel boot up.
4, Defeat the STOP switch on the front cabinet door.
5, Push the START button and bring the boom to the closed position
(support the boom tip if required).
Continue to fit LED Lights, Gom & End Cap as follows.

Step 6 Boom PS
Tip: before fitting the GOM rubber profile temporary fit the end cap and fit with the
supplied fixing. Remove cap and fixing and fit GOM rubber profile.
The end cap is contained within the boom
along with the GOM & LED light cover
9

Step 7 Boom PS
Temporary fit the Boom holder cover 7with one fixing screw 8. and fit GOM & Cover
The GOM profile will slide in to the grooves on the underside of the boom and the
top cover will clip onto the top of the boom. Both GOM and top cover can be cut to
suite the boom length.
Tip: when fitting the top cover apply downward and sideways pressure at the same
time.

Step 8 Light PS
With the boom in the open position use the winding handle to bring the boom
down to the closed position. Once the boom is in the closed position continue
to fit the LED light Strip (support boom tip if required).
Apply the R/G led strip into
the top boom channel. Apply
pressure to adhere the
adhesive
Start the LED strip
from V in the boom
holder.

Step 9 Boom Balancing
1, Position the boom in the vertical
position.
2, Set the A measurement as shown in
the chart and the correct Position in
relation to the boom length.
3, Remove the bolt with 24mm
spanner.
4, Bring the boom down so that the
boom rest at 45 degrees.
5, If necessary adjust the A
measurement to balance.
Example shows 5.5m Boom PS (lights
& GOM) A = 120mm,

Step10 Levelling the Boom
Once levelling is
complete fit boom
cover & BFT logo
cover 10

Installing the RGB Light Crown
There are two types of top crown, with LED lights and one without LED Lights. The crown is not
fitted to the cabinet on delivery and the installer will need to fit the crown and wire in the LED
crown if selected.
These components require
fitting before installation
ALLU2 Maxima Ultra

RGB Light Crown
Encoder/Reverser Fuse/Door/Swing Off Inverter
Maintenance Time Out/Limit Switch Other Error
The RGB light crown cover has additional functions. Fault present when flashing
Two questions to ask the customer: is the crown flashing & what is the colour

RGB Light Crown
The RGB lights in the top cover can work in 2 modes
1) Standard Red/Green for traffic lights
2) Parking lights Full/Free.
NOTE in these 2 modes the lights do NOT flash

CSB Xtream
See CSB Xtream instructions manual for programming