BGS technic 2188 User manual

SW-Stahl und Werkzeugvertriebs GmbH Tel. [phone] / 46438-0
F56essartSresukreveL ax +49 (0) 2191 / 46438-40
ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D
Instruction Manual
BGS technic KG
Bandwirkerstr. 3
42929 Wermelskirchen
Tel.: [phone]
Fax.: [phone]
[email protected]
www.bgstechnic.com
© BGS technic KG, Copying and further use not allowed
Art. 2188
DIGITAL TACHOMETER
TABLE OF CONTENTS
1. FEATURES
2. SPECIFICATIONS
3. DESCRIPTION OF CONTROLS
reflector marking
laser beam
target display
display
control knob
MEMORY button
Battery / cover
4. MEASUREMENT METHODS
5. MEMORY FUNCTION
6. BATTERY REPLACEMENT
1. FEATURES
-Measuring RPM is safe & accurate without attachment to object.
-Wide measuring range & high resolution.
-Digital display gives exact RPM with no guessing or errors.
-Used the exclusive MICRO-COMPUTER LSI-circuit and crystal time base to offer the high
accuracy measurement & fast measuring time.
-The last max. and min. value will be automatically stored in memory and can be displayed by turn
anytime.
-The use of durable, long-lasting components, including a strong, light weight ABS-plastic housing
assures maintenance free performance for many years. The housing has been carefully shaped to
fit comfortably in either hand.

SW-Stahl und Werkzeugvertriebs GmbH Tel. [phone] / 46438-0
F56essartSresukreveL ax +49 (0) 2191 / 46438-40
ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D
Instruction Manual
BGS technic KG
Bandwirkerstr. 3
42929 Wermelskirchen
Tel.: [phone]
Fax.: [phone]
[email protected]
www.bgstechnic.com
© BGS technic KG, Copying and further use not allowed
2. SPECIFICATIONS
Display 5 digits, 18mm (0.7”) LCD (Liquid Crystal Display),
with function annunciation.
Test Range 5 – 99.999 RPM
Resolution 0,1 RPM (< 1.000 RPM)
1 RPM ( 1.000 RPM)
Accuracy
(23 ± 5°C)
± 0.05%+1 digit
* Specific test in RF field strength is less than 3V/M
& frequency less than 330MHz.
Time Base quartz crystal, 4,194 MHz.
Circuit exclusive one-chip of microcomputer LSI circuit
Operation
Temp 0-50°C (32-122°F)
Max Humidity less than 80% R.H.
Datenspeicher last, lowest and highest measuring value
Battery 3x 1,5 V AA (UM-3)
Power
Consumption approx. 153 mA DC
Size 190 x 72 x 37mm (7,5 x 2,8 x 1,5 )“
Weight 235g (o,552 LB) / incl. battery (approx.)
Accessories
carrying case 1pc.
reflecting tape markes (600mm) 2pc.
operation manual 1pc.
3. FRONT PANEL DESCRIPTIONS
3-1 REFLECTIVE MARK
3-2 SIGNAL LIGHT BEAM
3-3 DISPLAY
3-4 MEASURE BUTTON
3-5 MEMORY BUTTON
3-6 BATTERY COMPARTMENT/COVER

SW-Stahl und Werkzeugvertriebs GmbH Tel. [phone] / 46438-0
F56essartSresukreveL ax +49 (0) 2191 / 46438-40
ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D
Instruction Manual
BGS technic KG
Bandwirkerstr. 3
42929 Wermelskirchen
Tel.: [phone]
Fax.: [phone]
[email protected]
www.bgstechnic.com
© BGS technic KG, Copying and further use not allowed
4. MEASURING PROCEDURE
Apply a reflective mark to the object being measured. Depress the MEASURE BUTTON (3-4) and
align the visible light beam (3-2) with the applied target. Verify that the MONITOR INDICATOR lights
when the target aligns with the beam (about 1 to 2 seconds).
MEASURING CONSIDERATION
Reflective mark
Cut and peel adhesive tape provided into approx. 12mm (0.5”) squares and apply one square to each
rotation shaft.
a. The non-reflective area must always be greater than the reflective area.
b. If the shaft is normally reflective, it must be covered with black tape or black paint before
attaching reflective tape.
c. Shaft surface must be clean and smooth before applying reflective tape.
Very low RPM measurement
As it is easy to get high resolution and fast sampling time, If measuring the very low RPM value,
suggest user to attach more “REFLECTIVE MARKS” averagely. Then divide the reading shown by
the number of “REFLECTIVE MARKS” averagely. Then divide the reading shown by the number of
“REFLECTIVE MERKS” to get the real RPM.
5. MEMORY FUNCTION
1.) A read out (the last value, max. value, min. value) obtained immediately before turning off the
MEASURE BUTTON is automatically memorized. For example, please ref. following fig.1.
Maxvalue
Min value
Measuring time
Last value
Di spla y
reading
Fig.1
2.) That memorized value can be displayed on the indicator by turn once depressing the memory
button, the symbol “UP” represents the Max. Value and “dn”, the Min value, “LA”, the last Value.
6. BATTERY REPLACEMENT
If the instrument is not be used for any extended period, remove batteries.
When it is necessary to replace the battery (battery voltage less than approx. 4V), “ ” will appear on
the display.
Slide the battery cover (3-6) away from the instrument and remove the battery.
Install the batteries 1.5V AAA (UM-4) correctly into the case.

SW-Stahl und Werkzeugvertriebs GmbH Tel. [phone] / 46438-0
F56essartSresukreveL ax +49 (0) 2191 / 46438-40
ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D
CE-Erklärung
BGS technic KG
Bandwirkerstr. 3
42929 Wermelskirchen
Tel.: [phone]
Fax.: [phone]
[email protected]
www.bgstechnic.com
EU-Konformitätserklärung
EC DECLARATION OF CONFORMITY
DÉCLARATION „CE“ DE CONFORMITE
DECLARATION DE CONFORMIDAD UE
Wir erklären in alleiniger Verantwortung, dass die Bauart der:
We declare that the following designated product:
Nous déclarons sous propre responsabilité que ce produit:
Declaramos bajo nuestra sola responsabilidad que este producto:
Digital-Drehzahlmesser ( BGS Art. 2188)
Digital Photo Tachometer
Compte-tours numérique
Taquímetro
folgenden einschlägigen Bestimmungen entspricht:
complies with the requirements of the:
est en conformité avec les réglementations ci-dessous :
esta conforme a las normas:
EC Council Directive 2004/108/EC
RoHS Directive 2011/65/EU
Angewandte Normen:
Identification of regulations / standards:
Norme appliquée:
Normas aplicadas:
EN 55022:2006+A1:2007
EN 55024:1998+A1:2001+A2:2003
Certificate No.: SEM10064452 / DT2234B
Report No.: STR10068058E
Certification No.: SEM13037242(RoHS)
Report No.: STR13038179R
Wermelskirchen, den 05.06.2013
ppa.
Frank Schottke, Prokurist
BGS technic KG, Bandwirkerstrasse 3, D-42929 Wermelskirchen