BluDot Browser Low Add-on Bookcase Quick start guide

Browser Low Add-on Bookcase
DESIGNED IN 2018
ASSEMBLY NOTES | REV 00
NEED A HAND?
Contact us at [email protected] or
844.425.8368 for assistance.
ALL BOOKED UP?
Be your own search engine. Browser is a wall-mounted shelving system
designed to be a capable solo unit or added to (endlessly) as needed.

1 | 844.425.8368 BROWSER LOW ADD-ON BOOKCASE
Rear Upright
Side Upright
1
1
QTY
QTY
PT. 1682
Measuring Tool
6
1
QTY
QTY
PT. 1683
Brace
3
1
QTY
QTY
PT. 9016
Shelf
1
3
QTY
QTY
Parts & Hardware

[e-mail] |2ASSEMBLY NOTES
PT. 1682 x 6PT. 9016 x 1
1 2
3/16” gap between
upright and bolt head
Step 01
PRE-INSTALL BOLTS AND POSITION ADJUSTABLE GLIDES.
Using the provided hardware, pre-attach the bolts to
the side uprights, leaving a small gap as shown for shelf
attachment on later steps.
The uprights contain floor glides that are recessed into
the base and adjustable with a wrench (not included
with product). Rotate the glides to a position that
reveals enough material so that your wrench will fit.
Do not remove the glides completely.

3 | 844.425.8368 BROWSER LOW ADD-ON BOOKCASE
PT. 9016 x 1wall fastener location
measuring tool
rear upright block
3/16” gap between
upright and bolt head
Step 02
MARK REAR UPRIGHT WALL LOCATION AND LOOSEN BOLTS.
Wall fasteners are not provided, please consult your local
hardware professional to determine the hardware best suited
for your wall type.
Position the measuring tool against the wall with the slot
resting on top of the rear upright block. Use a leveling device
to ensure that the measuring tool is level. Mark and drill the
wall fastener locations on the wall depending on the hardware
being used. Repeat for remaining rear upright block locations.
Loosen exterior bolts on side upright that is being extended,
leaving a small gap as shown for shelf attachment on later
steps.

[e-mail] |4ASSEMBLY NOTES
PT. 1683 x 1PT. 9016 x 1
wall fastener location
adjustable glide
Step 03
ATTACH REAR UPRIGHT, BRACES, AND SHELVES.
Position the rear upright against the wall with the glide facing
downwards. Use a leveling device to ensure that the upright
is plumb before fastening upright to wall in the locations
determined in previous step.
Using the provided hardware, attach the braces and shelves to
the grooves of the rear upright as shown.
A second person is recommended for holding the parts in
place during assembly.

5 | 844.425.8368 BROWSER LOW ADD-ON BOOKCASE
PT. 9016 x 1
1
2
Step 04
ATTACH SIDE UPRIGHT.
Install the side upright in the locations shown by pivoting the
shelf tabs to align with the pre-installed hardware. Ensure
that the end with the floor glides is facing downwards. Secure
the connection by tightening the hardware, holding the shelf
in place so that it remains seated on the screw.
Using a leveling device, adjust the glide on the upright to
ensure that the shelves are level and the upright is plumb.

[e-mail] |6ASSEMBLY NOTES
PT. 1683 x 2PT. 9016 x 1
Step 05
ATTACH REMAINING SHELVES.
Rotate the remaining shelves to position them between
the side uprights, then pivot and lower them to align
with the pre-installed hardware.
Secure the shelves to the back uprights using the
provided hardware as shown, then tighten the side
upright bolts as shown in the previous step.
Repeat for all remaining shelves.

BLU DOT DESIGN & MANUFACTURING, INC. DESIGNED IN MINNEAPOLIS, MN
PT. 9016 x 1
Additional Information
CLEAN
Clean with a slightly damp, soft cloth. To remove dirt and fingerprints, use quality cleaners formulated for
wood and metal furniture. Wipe completely dry with a soft cloth in the direction of the wood grain.
Step 06
ADJUST GLIDE AND TIGHTEN REMAINING BOLTS.
Use a leveling device and adjust the glide on the
upright to ensure that the shelves are level and the
upright is plumb.
Tighten the remaining pre-installed bolts on the
exterior of the side upright as shown.