BluDot MODU-LICIOUS User manual

WWW.BLUDOT.COM MODULICIOUS TWIN BED rev02 - PAGE 1 OF 5
HARDWARE
MODU-
LICIOUS
ASSEMBLY INSTRUCTIONS
Twin Bed
modular and stylish,
who knew?
CARE
PARTS LIST
A - End Drawer
Rib
H - Slat Support Rail J - Drawer
K - Drawer
Slide L - Bed Slats
I - Footboard
B - Inner Drawer
Rib E - Rib F - Side PanelC - Back Panel D - Side Rail
G - Headboard
x22
5002
x8
1611
x12
1608
x12
5013
x18
5001 x4
5010
x2
1612
x3
4010
x12
1023
x2
5016
x6
1211
x4
4005
Clean powder-coated
units with a soft cloth or
sponge using a mild
detergent, such as dish
soap, and warm water.
Wipe completely dry
with a soft cloth.
Clean with a slightly damp,
soft cloth. To remove dirt
and fingerprints, use a
quality cleaner formulated
for wood furniture. Wipe
completely dry with a soft
cloth in the direction of the
wood grain.
x2
x1
x1
x2
x2
x2
x1
x3
x1 x2
x6
x1

WWW.BLUDOT.COM MODULICIOUS TWIN BED rev02 - PAGE 2 OF 5
32 5
4
1
Turn cam clockwise
½ turn
HOW TO USE CAM
LOCK HARDWARE
Note direction of
arrow on cam
Note direction of
arrow on cam

WWW.BLUDOT.COM MODULICIOUS TWIN BED rev02 - PAGE 3 OF 5
2
34
ASSEMBLE ON
CARPET OR
PROTECTIVE MAT
1
x12
1023
First screw
goes here
AA
x2
front
both sides
back
Part A will have
1 panel with a
drawer slide insalled
on the front side only
(left) and 1 panel
with a drawer slide
installed on the back
side only (right).
Part B will
have drawer slides
insalled on both
the front and
back sides.
Part A is
thinner than
Part B
*
x8
5002 x4 5010
x4
5001
A
A
B
B
B
B
B
A
D
C
A
x8
1611 x3
4010
5001 5010
5010 5001
x8
5002 x8
5001
E
E
F
D

WWW.BLUDOT.COM MODULICIOUS TWIN BED rev02 - PAGE 4 OF 5
65
7 8
x2
5013
x2
5016
x2
1612
Long bolts
(#1612) are to be
used in conjunction
with brass fasteners
(#5016).
x4
5013
x2
5002 x4 1608
top
top
bottom
bottom
x4
4005
Drawer side
assembly can be
positioned on either
left or right side.
Instructions show
left side assembly.
x2
5001
x4
1608

WWW.BLUDOT.COM MODULICIOUS TWIN BED rev02 - PAGE 5 OF 5
9
10
x6
1211
NOTES
To remove drawers
pull lever up on the
right side and push
down on the left side
of the ball bearing
drawer slide.
Loosen the acorn
nuts, shift the drawer
front into place and
ask a friend to hold the
drawer front in place
while you re-tighten the
nuts (but don’t
over tighten).
Drawer fronts can
be adjusted if
drawer gaps
are inconsistent.
x4
5001
x6
5013
x4
5002 x4 1608
5001
5010
5001
use large
cams #5001
on side rails
(part D)
use small
cams #5010
on side panel
(part F)
F
D
D