BLUM AVENTOS HF User manual

AVENTOS HF
Subject to technical modifications without notice. © 2018 1
Telescopic arm set
▀ Telescopic arm (qty 2)
Cabinet heights Part no.
479 (18-7/8") — 558 (22") 20F3200.01
558 (22") — 686 (27") 20F3500.01
686 (27") — 889 (35") 20F3800.01
889 (35") — 1067 (42") 20F3900.01
Cover set
▀ Right and left cover plate
▀ Non-handed cover cap (qty 2) Part no.
Cover set 20F8000.NA
Lift mechanism set
▀ Lift mechanism (qty 2)
▀ #7 x 35 mm (1-3/8”) wood screw (qty 8)
Power factor Part no.
85 — 230 (1 lift mechanism req.) 20F2200.N5
231 — 470 20F2200.N5
471 — 880 20F2500.N5
780 — 1440 20F2800.N5
1401 — 2300 (3 lift mechanisms req.) 20F2800.N5
Wood or wide alum door hardware set
▀ CLIP top 120° hinge (qty 2)
▀ COMPACT 33° hinge (qty 2)
▀ CLIP top bottom door hinge (qty 2)
▀ COMPACT mounting plate (qty 2)
▀ Face frame adapter (qty 4)
▀ Telescopic arm mounting plate (qty 2)
NOTE: Three hinges and mounting plates required
for cabinet widths over 1219 (48")
Hardware set 78Z5530TA8
Inst. screw for wood doors 606N or 606P
Inst. screw for wide alum doors 7072A
Mounting plate with bracket set
▀ Left and right mounting plate with bracket
▀ For large overlay five-piece doors
Part no.
Mounting plate w/ bracket set 175H3F00
Wood/wide aluminum
frame door application
Part no.

Subject to technical modifications without notice. © 2018
2
1Locating pin locations
Panel
TR = Top reveal
TDH = Top door height
Top door height
(TDH) Y
231 to 271 TDH x .6 - 28 + TR
272 to 531 TDH x .6 - 57 + TR
Face frame
Top door height
(TDH) Y
231 to 271 TDH x .6 - 28 + TR
272 to 531 TDH x .6 - 57 + TR
TR = Top reveal
TDH = Top door height
192
Y
37
TDH
TR
Ø5
NOTE: Face frame
cabinets must be blocked
out flush with the frame
Assembly
Universal individual template is available for pre-boring locating pins
Part no.
65.1051.02
WARNING
Risk of injury from spring-loaded arm
▀ Do not push arm assembly down or leave in the down position
▀ Remove mechanism before installing or removing cabinet
192
Y
37
Top door height
TR
Ø5

3
Subject to technical modifications without notice. © 2018
Align the lift mechanism in the cabinet using the 5 mm locator pins and attach the mechanism with the four
wood screws provided.
2Attaching the lift mechanism
#7 x 35 mm (1-3/8") wood screws (qty 4)
3Attach the telescopic arms
WARNING: Risk of injury from spring loaded arm.
Attach telescopic arms by clipping them on in
the fully upright position.
min 5
5

Subject to technical modifications without notice. © 2018
4
4Small overlay top door hinge planning CLIP top hinges
5Large overlay top door hinge planning COMPACT hinges
B
overlay
12.7
overlay
B
1/2"
Part no.
CLIP top hinge 70T5580.TL
Mounting plate 175H6000
Part no.
COMPACT hinge
32.4630
Mounting plate 130.1130.02
Overlay table
13 * 14 15 16 17
33456
B Bore distance
* Bore at 3 then adjust 1
Overlay table
1-1/4”
3
Bore distance
Assembly

5
Subject to technical modifications without notice. © 2018
reveal
B
12.7
Reveal table
6 5 4 3
3 4 5 6
B Bore distance
Part no.
CLIP top hinge 78Z5530T
Mounting plate 175H6000
6Bottom door hinge planning
7a
NOTE: For five-piece door mounting
specifications, see page 6
Attaching the telescopic arm mounting plates
12.5+Overlay
XTDH
17
min.
Top door
height (TDH) X
231 to 271 TDH x .5 + 70
272 to 531 TDH x .5 + 47
Part no.
175H3100
Telescopic arm mounting plate

Subject to technical modifications without notice. © 2018
6
less than 6
12.5
19
12.5
ü
Standard mounting plate works
Attaching the telescopic arm mounting plate with bracket for five-piece doors
7b
more than 6
12.5
ü
Standard mounting plate does not work
Use mounting plate with bracket when
panel is < 6 mm from screw
Part no.
175H3F00
Telescopic arm mounting plate with bracket
Assembly

7
Subject to technical modifications without notice. © 2018
8Attach the top door to the cabinet
9Attach the bottom door
Attach bottom door to the top door and attach the telescopic arms 1
a b

Subject to technical modifications without notice. © 2018
8
11 Finalizing the door adjustments
1. Adjust each top door hinge and mounting plate
to properly align the top door to the cabinet.
2. Adjust each bottom door hinge and mounting
plate to properly align doors to the cabinet and
to the top door.
± 2 mm± 2.5 mm ± 2 mm± 2 mm± 3 mm + 3/- 2 mm
1 2
Adjust tension of the mechanism
10
Close and flush doors to cabinet. Open and close door to test closing force. Use a screw gun and the #2x2 POZI
driver bit to adjust the lift mechanism to the desired tension. Test door again and repeat until
desired function is achieved.
Tension adjustment should be the same on both lift mechanisms.
2
1
Although not illustrated here, telescopic arm mounting plates can also be adjusted horizontally ± 2 mm if ne e ded.
Assembly

9
Subject to technical modifications without notice. © 2018
13 Attach covers
Attach the left and right cover plates to each lift mechanism then attach the symmetrical cover caps
Adjust and lock telescopic arms
12
1. Close and flush doors to cabinet. While pressing on
the top door, pull the bottom door open one inch.
12
2. Slightly open door and lock the telescopic arms
into position using the levers as shown.
Open door
enough to
lock levers

Subject to technical modifications without notice. © 2018
10
Detaching the telescopic arms
1
2
Remove covers
WARNING
Release both arms and gently rest the top
door on the loose arms. The tension will hold
the doors up for the next step.
Warning: Risk of injury
from spring-loaded
telescopic arm!
Maintain control of telescopic arm while
releasing the CLIP mechanism.
Removal
Risk of injury from spring-loaded arm
▀ Do not push arm assembly down or leave in the down position
▀ Remove mechanism before installing or removing cabinet
1
2
1
2