Body Craft F609 User manual

QUESTION?
As a quality home gym supplier we are committed to your complete satisfaction. If you have questions,
or find missing or damaged parts, we will guarantee your complete satisfaction through our authorized
dealer service centers or our home office customer service department. Please call your local dealer
for assistance or RSI at 800-990-5556 (9:00 AM - 5:00 PM). Our trained technicians will provide
immediate assistance to you, free of charge.
We stand behind our products. Every piece, every part of this BODYCRAFT strength training system
is guaranteed for as long as you own it. We will repair or replace anything that goes wrong.
Bodycraft is a division of Recreation Supply Inc.
P.O. BOX 181
Sunbury, OH 43074
INSTRUCTION MANUAL
OLYMPIC COMBINATION BENCH
STRENGTH TRAINING SYSTEM
MODEL : F609
79500

1
BEFORE YOU BEGIN
Congratulations and thank you for selecting the Olympic Combination Bench
strength training system. The Olympic Combination Bench offers an impressive
array of strength training exercises to develop every major muscle group of the
body. Whether your goal is cardiovascular fitness, a shapely, toned body or
dramatic muscle size and strength, the Olympic Combination Bench will help
you achieve the specific results you want.
For your safety and benefit, read this manual and the accompanying literature
before using the Olympic Combination Bench. Keep this manual for future
reference.
If you have additional questions, please call your local BODYCRAFT dealer or
our customer service department at 800-990-5556 Monday through Friday,
9 a.m. until 5 p.m. Eastern Time.
IMPORTANT SAFETY NOTES
There is a risk assumed by individuals who use this type of equipment.
Before beginning this or any other exercise program consult your physician.
This is especially important for individuals over the age of 35 or persons
with pre-existing health problems. Recreation Supply, Inc. assumes no
responsibility for personal injury or property damage sustained by or
through use of this product.
1.This product must be assembled on a flat, level surface to assure its
proper function.
2.Clean pads and frame on a regular basis. We recommend warm, soapy
water. Do not use harsh or abrasive chemicals.
3. Inspect and tighten all parts before every use. Replace any worn parts
immediately. Failure to do so may result in serious injury.
4.Keep children away from the Olympic Combination Bench at all times.
5.Keep your hands away from moving parts other than the designated
handles.
6.When adjusting the seat, make sure the spring pin is fully engaged.
If not, the seat may slip and cause serious injury.
7.Exercise with care to avoid injury.
8.If unsure about the proper use of the Olympic Combination Bench strength
training system call your local BODYCRAFT dealer or our customer
service department at 800-990-5556.

24
39
24
39
26
51
40
22
24
24
24
24
19
28
25
43
21
27
49
27
20
26
20
13
29
26
48
36
48
21
48
26
14
29
26
20
20
42
51
42
16
51
51 49
51
51
49
48
35
26
13
29
26
48
36
48
21
48
26
14
29
26
48
35
49
41
41
51
49
16
49
51
29
54
26
30
17
52
44
52
27
27 27
50
27
52
44
10
10
21
41
50
37
38
41
45
49
51
19
46
55
53
18
49
51
23
53
55
46
39
39
39 39
41
31
51 15
21
47
15
32
34
23
12
22
22
15
27
33
27
47
11
3
4
5
6
2
7
9
8
1
EXPLODED VIEW
2

PARTS CHART
0
(inch) 1" 2" 3"1/21/4 3/4 1/2 1/2 4" 5" 6"1/2 1/2 1/2
NO. DESCRIPTION QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
1
1
1
1
1
1
1
2
1
2
1
1
2
2
3
2
1
1
2
4
5
3
2
6
1
10
8
1
5
1
1
1
1
1
2
2
1
1
6
1
6
4
2
2
2
2
2
8
9
2
16
4
2
1
2
FRONT STABILIZER
LEG EXTENSION / CURL SLEEVE
SEAT SUPPORT
UPRIGHT CONNECTOR
RIGHT UPRIGHT
LEFT UPRIGHT
SEAT SLIDER
SEAT HINGE
BACK SUPPORT
BACK SUPPORT PLATE
LEG EXTENSION HOLDER
LEG EXTENSION
SAFETY ARM
BAR CATCH
FOAM ROLLER HOLDER
BACKING PLATE
U PIN
LEG EXTENSION AXLE
45mm X 75mm CAP
75mm X 45mm CAP
45mm X 75mm PLUG
50mm SQUARE PLUG
1" ROUND PLUG
1"ID FOAM ROLLER PLUG
SPACER
45mm X 75mm SLIDER
STEEL BUSHING
110mm POP PIN
90mm POP PIN
KNOB
L PIN
SPRING CLIP
STOPPER
RUBBER DONUT
BUMPER FOR SAFETY ARM
BUMPER FOR BAR CATCH
SEAT PAD
BACK PAD
FOAM ROLLER
1/2" X 4-3/4" HEX HEAD BOLT
1/2" X 4" HEX HEAD BOLT
1/2" X 3" HEX HEAD BOLT
1/2" X 2-1/2" HEX HEAD BOLT
3/8" X 2-3/4" HEX HEAD BOLT
3/8" X 1" HEX HEAD BOLT
5/16" X 5/8" ROUND BOLT
5/16" X 12mm SET SCREW
4.5mm X 10mm SCREW
1/2" NYLON NUT
1/2" NYLON NUT (THINNER)
1/2" WASHER
3/8" WASHER
5/16" WASHER
METAL CAP
5/16" SPRING WASHER
3
4
1 2
3
5 6
7 8
9
10 11
12 13 14 16
15
17
18 19 20 21 22 23 24 25
26 27 28 29
34 35
37
3938
40 41 42 43 44 45
46 47 48 49 50
51 52 53 54 55
36
30 31 32 33

19
25
43
21
49
20
20
21
20
20
42
51
42
16
51
51
49
51
51
49
21
49
41 41
51
49
16
49
51
30
49
51
19
23
21
3
4
5
6
2
7
1
41
51
4
Do NOT tighten bolts until instructed.
1. Attach Leg Extension Sleeve (2) to Front Stabilizer (1) using two 1/2" X 4" Hex Bolts (41), four 1/2"
Washers(51) and, two 1/2" Nylon Nuts (49). Attach two 45mm X 75 mm Caps(19) to Front Stabilizer
(1).
2. Attach Upright Connector (4) to Right and Left Uprights (5, 6) (numbers sticker should face inside),
using Backing Plate (16), two 1/2" X 3" Hex Bolts (42), four 1/2" Washers (51) and two 1/2" Nylon
Nuts (49). Attach four 75mm X 45mm Caps (20) to Right and Left Upright bottoms, and two 45mm X
75 mm Plugs (21) to top of Uprights.
3. Slide Seat Slider(7) onto Seat Support(3) with welded metal tabs facing toward rear of bench as shown.
Attach Seat Support (3) to Upright Connector (4) using two 1/2" X 4" Hex Bolts (41) and two 1/2"
Nylon Nuts (49).
4. Attach Seat Support (3) to Leg Extension Sleeve (2), using two 1/2" X 2-1/2" Hex Bolts (43) and two
1/2" Washers (51). Attach a 45mm x 75 mm Plug (21) to Seat Support (3).
STEP 1 Assembly Instructions

24
39
24
39
22
24
24
24
24
13
14
13
14
52
44
52
52
44
10
21
50
37
38
41
45
46
55
53
18
53
55
46
39
39
39 39
31
15
47
15
32
34
23 12
22
22
15
33
47
11
3
5
6
27
9
8
51
40
49
51
5
1. Attach Leg Extension (12) onto Leg Extension Sleeve (11) using Axle (18), two 5/16 Washers (53),
two Spring Washers (55) and two 5/16" X 5/8" Round Bolts (46). Attach three 50mm square Plugs
(22) to Leg Extension (12). Insert Leg Extension Holder (11) into Leg Extension Sleeve (2) by pulling
pre-installed Pop Pin (28) out.
2. Insert two Foam Roller Holders (15) into holes in Leg Extension (12). Slide Four Foam Rollers (39)
onto each end of Foam Roller Holders (15). Insert 1" ID Foam Roller Plugs (24) onto each end of
Foam Roller Holder (15). Slide Rubber Donut (34) onto weight holder on Leg Extension (12). Spring
Clip (32) is provided to hold weight plates in place.
3. Insert a Foam Roller Holder (15) into hole in Leg Extension Sleeve (11). Slide Foam Rollers (39) onto
each end of Foam Roller Holders (15). Insert 1" ID Foam Roller Plugs (24) onto each end of Foam
Roller Holder (15). Note: L Pin (31) is used to lock Leg Extension (12) into place when performing
decline exercises. Remove it when performing leg extensions and leg curls.
4. Slide Seat Hinges (8) onto axle on Seat Slider (7). Attach Seat Pad (37) to Seat Hinges (8) using two
3/8" X 1" Hex Bolts (45) and two 3/8" Washers (52).
5. Attach Back Support (9) to welded tabs on Seat Slider (7) using one 1/2" x 4-3/4" Bolt (40), two
Washers (51), and a 1/2" Nylon Nut (49). Attach two Back Support Plates (10) to Seat Support (3)
using 1/2" X 4-3/4' Bolt (40) and one 1/2" Thin Nylon Nut (50). Attach Back Pad (38) to Back Support
(9) using two 3/8" X 2 -3/4" Bolts (44) and two 3/8" Washers (52).
6. Slide Safety Arms (13) and Bar Catches (14) over top of Uprights (tabs facing up) and secure at your
desired height. For Squats, Safety Arm and Bar Catch can be reversed, facing toward rear.
Tighten all bolts. Bolts at pivot points can be loosened slightly (1/4 - 1/2 turn).
STEP 2 Assembly Instructions

6
Assembly is complete! Please take the following steps before using the
BODYCRAFT OLYMPIC COMBINATION BENCH :
1.
2.
Make certain all bolts are tightened securely.
Enjoy many years of a Fit Lifestyle.
Thank you for purchasing the Bodycraft Olympic combination bench
Machine Training System. If You have any questions, please call
your local BodyCraft dealer or call our customer service department
at 800-990-5556