Bosch AMAX 2100 User manual

AMAX
2100 / 3000 / 4000
en User Guide

Table of contents
1Introduction 4
2Arming and Disarming the System 10
2.1 Arming the System 10
2.1.1 Arming in AWAY Mode 10
2.1.2 Arming in STAY Mode 11
2.1.3 Forced Arming 11
2.2 Disarming the System 11
2.2.1 Disarming with Code 11
2.2.2 Disarming with Key Switch 11
3Faults and Tamper Conditions 12
3.1 System Fault or Tamper Analysis Mode LED Keypad 12
3.2 System Fault or Tamper Analysis Mode Text Keypad 12
4System Test 15
4.1 Siren Test 15
4.2 Communication Test 15
4.3 Walk Test Mode 15
5Event Log Recall Mode 16
6Reset the Control Panel 17
7Bypassing 18
7.1 Bypassing Zones 18
8Codes 19
8.1 Add/Change and Delete User Code 19
8.2 Change Individual Code 20
9Keypad Alarm Operation Commands 21
9.1 Keypad Panic Alarm 21
9.2 Keypad Fire Alarm 21
9.3 Keypad Medical Alarm 21
10 Domestic Dialing 22
AMAX Table of Contents | en 3
Bosch Sicherheitsysteme GmbH User Guide 2014.01 | 02 | F.01U.295.569

Introduction
IUI-AMAX4-TEXT
IUI-AMAX3-LED8 IUI-AMAX3-LED16
IUI-AMAX-LED8 IUI-AMAX-LCD8
1
4en | Introduction AMAX
2014.01 | 02 | F.01U.295.569 User Guide Bosch Sicherheitsysteme GmbH

Notice!
In some country versions Installer Code is needed to reset tamper alarm.
Quick Keypad Operation Instructions
Function Command
Default User Code = 2580
D A B S M I
N
Arm / Disarm
AWAY arm [Code] + [#] / [#] (Quick arm) √ √ √ √ √ √
STAY arm [Code] + [*] / [*] (Quick arm) √ √ √ √ √ √
Disarm [Code] + [#] √ √ √ √ √
Display
Display Info (Fault/
Tamper..)
[Code] + [2] [1] + [#] √ √
Bypass
Zone Bypass/Cancel [Code] + [3][1] + [#] + [Zone No] [*] + [#]
(Bypass)
√ √ √ √
[Code] + [3][1] + [#] + [Zone No] [*] + [#]
(Cancel LED)
√ √ √ √
[Code] + [3][2] + [#] + [Zone No] [*] + [#]
(Cancel Text KP)
√ √ √ √
Bypass Inquiry [Code] + [3][3] + [#] (Text KP) √ √ √ √
Bypass Fault/Tamper [Code] + [3][4] + [#] √ √
Reset
Reset [Code] + [6] + [#] √ √
Alarm commands
Keypad Emergency Alarm Long press [1] and [3] or [*] and [#]
Keypad Fire Long press [4] and [6]
Keypad Medical Alarm Long press [7] and [9]
D = Duress User
A = Arming User
B = Basic User
S = Super User
M = Master User
IN = Install User
AMAX Introduction | en 5
Bosch Sicherheitsysteme GmbH User Guide 2014.01 | 02 | F.01U.295.569

Function Command D A B S M I
N
Other Commands
Switch to Main Keypad [Code] + [0][0][0] + [#] (Text KP) √ √ √
Switch to Area 01-16 [Code] + [0][ _ ][ _ ] + [#] √ √ √
Fault/Tamper Inquire [Code] + [2][1] + [#] √ √
Check all Event Log [Code] + [2][2] + [#] (Text KP) √ √
Check EN Event Log [Code] + [2][3] + [#] (Text KP) √ √
Check Dialer Event Log [Code] + [2][4] + [#] (Text KP) √ √
Siren Test [Code] + [4][1] + [#] √ √
Communication Test [Code] + [4][2] + [#] √ √
Walk Test [Code] + [4][3] + [#] √ √
Change / View date / Time [Code] + [5][1] + [#] √
Daylight Saving Time (+1h) [Code] + [5][2] + [#] √ √
Daylight Saving Time (-1h) [Code] + [5][3] + [#] √ √
Add / Delete / Change User [Code] + [5][4] + [#] √ √
Change Individual Code [Code] + [5][5] + [#] √ √
Change Domestic Phone
No.1-4
[Code] + [5][6][#] + [ _ ] + [#] + [ _ _ _ _ _
_ ][#] (Text KP)
√
Call Back [Code] + [5][7] + [#] √ √
Change Language [Code] + [5][8] + [#] + [ _ ] [ _ ] + [#]
01=EN 02=DE 03=ES 04=FR
05=IT 06=PL 07=NL 08=SE
√√
Installer Access [Code] + [7][1] + [#] (Enable)
[Code] + [7][2] + [#] (Disable)
√
System Reset [Code] + [9][9][8][9] + [#] √ √
Installer Program Mode [Code] + [9][5][8] + [#] √
D = Duress User
A = Arming User
B = Basic User
S = Super User
M = Master User
IN = Install User
6en | Introduction AMAX
2014.01 | 02 | F.01U.295.569 User Guide Bosch Sicherheitsysteme GmbH

USER MENU
ARM/DISARM
INSTALLER ACCESS
SYSTEM SETTINGS
INQUIRE
ZN/FLT/TAMP BYPASS
RESET
ARM AWAY
ARM STAY
DISARM
BYPASS FLT./TAMP.
ZONE BYPASS
ZONE BYPASS CANCEL
BYPASS INQUIRE
PRINT ENABLE
FAULT/TAMP INQUIRE
ALL EVENT RECALL
EN EVENT RECALL
EVENT PRINT
DIAL EVENT RECALL
ENABLE INSTALLER
DISABLE INSTALLER
DAYL.SAV.TIME -1h
ADD/CHG USER CODE
CHANGE INDIV CODE
INITIATE CALL BACK
CHANGE LANGUAGE
DAYL.SAV.TIME +1h
Figure 1.1: User Menu
AMAX Introduction | en 7
Bosch Sicherheitsysteme GmbH User Guide 2014.01 | 02 | F.01U.295.569

Keypad Indicators
Keypad Indicator
Icons
Status Definition
1 2 3 ….
ZONE (1-8)
on Zone is triggered.
off Zone is normal.
Fast flash (0.25 seconds lights on/
0.25 seconds lights off)
Zone was alarmed or is in alarm
status.
Slow flash (1 second lights on/1
second lights off)
Zone is manually bypassed or
interior Zone is in STAY arm mode.
AWAY
on System is armed in AWAY mode.
off System not armed in AWAY mode.
Slow flash (1 second lights on/1
second lights off)
Exit time.
Fast flash (0.25 seconds lights on/
0.25 seconds lights off)
Programming mode or Code
function mode. STAY indicator
flashes simultaneously.
STAY
on System is armed in STAY mode.
off System not armed in STAY mode.
Slow flash (1 second lights on/1
second lights off)
Exit time.
Fast flash (0.25 seconds lights on/
0.25 seconds lights off)
Programming mode or Code
function mode. AWAY indicator
flashes simultaneously.When
bypass function is performed, the
STAY indicator only flashes.
MAINS
on AC main power is normal.
Slow flash (1 second lights on/1
second lights off)
AC main power supply failed.
FAULTS
on System fault or Tamper condition
is present.
off System is in normal status.
Flashes System fault or Tamper condition
must be acknowledged.
on System is disarmed.
8en | Introduction AMAX
2014.01 | 02 | F.01U.295.569 User Guide Bosch Sicherheitsysteme GmbH

Keypad Sounds
Sound Indicator Definition
One short beep A keypad button has been pressed.
One single one- second beep The requested operation is refused. Incorrect
operation signal.
Two short beeps The system accepted the code. The system executed
the requested function.
One short beep every minute Fault tone, unacknowledged system failure.
One short beep every two seconds Exit time started.
Continued sound – Last 10s on exit time
– Keypad fault/tamper sound (fault/tamper to be
acknowledged)
– Keypad alarm sound
Continuous 0.5 second beep, stops
0.5 seconds
Entry delay time (until alarm ends or system is
disarmed).
AMAX Introduction | en 9
Bosch Sicherheitsysteme GmbH User Guide 2014.01 | 02 | F.01U.295.569

Arming and Disarming the System
Arming the System
Notice!
When the number of incorrect code entries on the keypad reaches a specified limit, the
keypad will automatically lock for 180 seconds and alarm is reported. If the keypad is idle for
1 minute, the system will automatically exit from any operational mode.
Arming in AWAY Mode
Arming the system in AWAY mode is normally performed when you leave the premises and
require that all zones are activated in a ready state to detect an intrusion.
Keypad Arming
There are two methods to arm your system in AWAY mode.
Method 1:
To arm the System in AWAY mode enter your code and press [#].
It beeps twice, the AWAY indicator flashes slow, and exit time starts.
After the exit time, the AWAY indicator turns on.
Method 2:
To arm the System in AWAY mode press and hold [#] until it beeps twice.
The AWAY indicator flashes slow, and exit time starts. After the exit time, the AWAY indicator
is on.
Please contact your installer to enable/disable this function.
Telephone Remote Arming
The user dials the control panel number. The control panel answers the call and issues a long
beep. After the long beep, the user must press the [#] key. When the Panel receives the signal
it will confirm the arming of the control panel with a high tone.
Please contact your installer to enable/disable this function.
Notice!
Telephone arming is possible when the system has only 1 assigned area.
Key Switch Arming
Users can use a key switch to Arm and Disarm the system. When the Key switch is activated,
the AWAY indicator flashes slow and exit time starts. After exit time, the AWAY indicator is lit.
When the Key switch is deactivated, the system is disarmed and Away indicator is off.
2
2.1
2.1.1
10 en | Arming and Disarming the System AMAX
2014.01 | 02 | F.01U.295.569 User Guide Bosch Sicherheitsysteme GmbH