Bosch VIDEOJET decoder 3000 Instruction manual

For Sales & Service, Please Contact;
Electronic Security & Data Communications
Phone: [phone]
www.bjrsecurity.com.au
This document has been designed as a quick users guide for the Bosch Solution 2000 / 3000 alarm system.
Please refer to the full users guide provided for more information when operating the system.
A copy of the full users guide can be downloaded from our website www.bjrsecurity.com.au/downloads.htm
SCAN HERE TO VISIT
OUR DOWNLOADS PAGE
Document: BJR-B3000-QUG V05 Updated: 02 November 2015
Copyright BJR Security 2015
ALARMS MONITORING CCTV ACCESS CONTROL PHONE & DATA CABLING
BOSCH SOLUTION 2000 / 3000
QUICK USERS GUIDE

How To Change Codes
Only the 'master code' (user 1) can be used to add, change or delete codes. If you only have 1 code,
typically this will be the 'master code'
1. Enter your master code then press [1] and [#AWAY] for example [2] [5] [8] [0] [1] [#AWAY]
2. Enter the user number (1-32) your wish to change then press [#AWAY] for example, the master code
is user number 1, to change the master code enter [1] [#AWAY]
3. Enter the new code for the user then press [#AWAY] for example [5] [6] [7] [8] [#AWAY]
Repeat steps 1-3 above to add any additional codes. Note: For security reasons, avoid any easy to guess
codes, ie 1234, your postcode, street address ect.
Keypad Display Icons & Meanings
Zone Indicators
Refer to zone list on
keypad flip cover for
zone number device
type and location.
On - Indicates which zones are unsealed (motion sensors detecting motion,
door open ect)
Off - Zone is sealed
Flashing fast (0.25 Sec on / 0.25 Sec off) - Indicates that zone has gone into
alarm recently, arming the system will clear this away
Flashing slow (1 sec on / 1 sec off) - Zone is isolated
Mains Power
On - Alarm has mains AC power (Normal)
Flashing - Alarm has no mains AC power and is running on backup battery
only, check alarm plug pack is plugged in and power point is on.
System Is Disarmed
The alarm system is disarmed (OFF)
Armed - AWAY mode
The alarm is armed in AWAY mode (all armed)
Armed - STAY mode
The alarm is armed in STAY mode (partial armed)
System Fault
Off - There are no system faults (Normal)
On / Flashing - There are system faults (power failure, phone line failure,
siren failure, low batteries, tampers ect)
The codepad may beep once per minute to indicate there is a fault, to stop
this press the # AWAY button once to acknowledge the fault.
Refer to full User Guide section 5.6 'Fault Analysis Mode' to determine
the type of fault and contact BJR Security if required.
Armed Indicator
The alarm system is armed in either AWAY or STAY mode.
Disarmed Indicator
The alarm system is disarmed.
The icon will flash if any zone is unsealed letting you know the system may
not be ready to arm.
How To Arm
To arm the whole alarm
Enter your 4 digit code then the [#AWAY] button
To arm in stay mode (arm only part of the house or office)
Enter your 4 digit code then the [*STAY] button
(Only zones discussed with your installer at time of installation will be armed in this mode)
How To Disarm
Enter your 4 digit code then the [#AWAY] button
Using The Remote Controls (Optional add on)
To use the remote, press and hold the required button until the transmit light comes on.
Arm the system in AWAY (full) mode
Disarm the system
Optional feature ___________________________
Arm the system in STAY (partial) mode
(If setup by the technician at time of installation)
1. Arm / Disarm (toggles) in AWAY mode (full arm)
2. Arm / Disarm (toggles) in STAY mode (partial arm)
3. Optional feature ___________________________
4. Optional feature ___________________________
Panic function: Press and hold BOTH button 1 & 2 (the locked and unlocked padlock on the black
remotes) at the same time for approximately 4 seconds or until the sirens are activated.