BOSS ILLUMINATION NIMBUS S User manual

www.bia.lighting | [email protected]page 1 / 3
PRODUCT MANUAL
COPYRIGHT BIA ©2020 V08.20
WARRANTY STATEMENT This product is covered by a 5 year replacement warranty.
BIA guarantees this product to be free of defects from the date of purchase for the stated period above. If product fails within the warranty period, BIA will x
or replace the product. This excludes any costs associated with the removal or installation of product. This warranty is subject to the terms and conditions stated
on www.bia.lighting. Failure to comply with installation guidelines will automatically void the warranty. Please retain purchase receipt. For more information on
warranty please visit www.bia.lighting/warranty
BIA reserves the right to change specications and other information, modify products and discontinue items without prior notication.
PRODUCT VARIANTS
Nimbus S: 10W
20W
30W
40W
50W
Nimbus M: 60W
75W
90W
Nimbus L: 130W
180W
CCT: 3000K
4000K
5000K
Beam Angle: Type II
Type III
Type IV
Dimming: Non-dimmable
1-10V
DALI
Photocell: Ye s
No
Colour: Black
Dark grey
NEMA Base: 3-pin
5-pin
7-pin
PRODUCT SPECIFICATIONS
Input Voltage : 100-240VAC
Operating Temperature : -10 to 40°C
Material : Aluminium
NIMBUS
STREET LIGHT
Must be installed by
a licensed electrician.
Must be installed
in accordance with
relevant Australian
Standards.
ADDITIONAL INFORMATION
1. NEMA socket is compatible with third party NEMA outdoor
lighting controllers.
2. If cleaning maintenance is required, disconnect from mains
supply and allow luminaire to cool. Use a clean microbre cloth,
slightly dampened with a mild dilution of detergent that is PH
neutral, alcohol free and non-abrasive.
3. Do not use harsh chemicals or solvents. Do not use high pressure
cleaners.
4. Care must be taken during installation and maintenance to
prevent accidental damage to the surface of the luminaire. These
damages may result in corrosion.
PARTS INCLUDED
Cable
S: 10m
M: 15m
L: 15m
NEMA 7-pin
base
NEMA 3-pin
blank module
LED
Luminaire
IP66 IK0860mm
OPTIONAL COMPATIBLE PARTS sold separately
Photocell 60mm
to 40mm
adapter
Disclaimer: Please read this product
manual carefully before installing the
product.
Warranty is void if installation
guidelines are disregarded, if the
product has been modied, or if
damage is caused by misuse or
improper installation.
Images, drawings and diagrams are for
illustrative purposes only.
BIA products are manufactured
and certied in accordance with all
mandatory Australian Standards.
Technical data and information subject
to changes. Please visit our website
for latest version.
x1

www.bia.lighting | [email protected]page 2 / 3
PRODUCT MANUAL
COPYRIGHT BIA ©2020 V08.20
INSTALLATION INSTRUCTIONS
A INSTALLING THE BRACKET
1. Remove the bolt screws.
2. To install the spigot bracket, slide it onto the luminaire as shown.
Spigot bracket can be installed at 90° or 180°.
3. Tighten the bolt screws to secure the bracket.
B ADJUSTING THE ANGLE
1. Loosen the bolt screws and adjust the spigot bracket by sliding it
up or down.
2. Tighten the bolt screws to secure the bracket.
C INSTALLATION
1. Ensure pole of the correct diametre has been installed/supplied.
2. Feed wiring cable through spigot. Cable should be terminated
within the pole and to the IP rating required.
3. Place luminare over spigot and slide it all the way in.
4. Tighten the screws to rmly secure luminaire.
IMPORTANT NOTE: All connections made must be
waterproofed to the appropriate IP rating for the application.
Warranty is void if connection IP ratings are not met.
90º
180º
4
1
2
3
+15º
90º
-15º
+15º
180º
-15º
1
2
3
+15º
0
-15º
LUMINAIRE CONTROLLER
INSTALLATION
1. Twist anti-clockwise to remove the
blank module.
2. Twist in the luminaire controller,
clockwise until it clicks.
1
1
2
2

www.bia.lighting | [email protected]page 3 / 3
PRODUCT MANUAL
COPYRIGHT BIA ©2020 V08.20
DIMENSION DIAGRAM
279mm279mm329mm
550mm
650mm
780mm
119mm119mm119mm
Nimbus S
weight: 5.5kg
Nimbus M
weight: 7kg
Nimbus L
weight: 8.5kg