Breezesta Palm Beach PB-1608 User manual

PALM BEACH RIGHTHAND ARM
LOUNGE CHAIR - PB-1608
1 PB-1608 Assembly

A
B
C
D
E
F
G
H
a b
c d e
f
g
h
i
Suggested Tools:
Drill, Plastic Mallet
FOR USE IF CONNECTING FURNITURE-SEE LAST
PAGE OF INSTRUCTIONS
PARTS
PART DESCRIPTION PART NO. QTY
A PB ARMLESS LH FRAME SA-00369 1
B PB LOUNGE CHAIR RH FRAME SA-00384 1
C 24"X24" SEAT SLING H-0000-SLG 1
D PB SLING SPACER ASSEMBLY SA-00382 1
E PB SLING RAIL ASSEMBLY SA-00407 1
F PB SLING RAIL ASSEMBLY SA-00408 1
G PB 1-ARM LOUNGE BACK SLAT PRT-00863 3
H PB 1-ARM LOUNGE FRONT BOTTOM SPREADER PRT-00866 1
SA-00399 HARDWARE KIT
PART DESCRIPTION PART NO. QTY
a
#8 X 1-1/4" TORX SCREW H-0000-S8125
12
b #8 X 1-3/4" TORX SCREW H-0000-S8175 12
c #8 X 2-1/2" TORX SCREW H-0000-S825 6
d 1/4"-10 X 3" LAG SCREW H-0000-S103 1
e T-20 & T-25 TORX BIT H-0000-CTD 1
f LEVELING MOUNT H-0000-LM 4
g 6-INCH T20 TORX BIT H-0000-T20X6 1
h CONNECTOR PLATE H-0000-CP 2
i #8 X 1-1/4" TORX SCREW-UNPAINTED H-0000-S8125 8
2 PB-1608 Assembly

G
A
1.
Place Frame Assembly
A
on a flat surface either
as shown or with the slats
on the ground and frame
sticking up in the air. Insert
the 3 Back Slats
G
into the
slots of the frame. This may
require some tapping with
a mallet to set them firmly
into the slot.
The Back Slat tenon is
offset, and is positioned to
the rear of the chair as
seen at left.
2.
If you did not start with the
slats on the floor, carefully rotate
the chair to its back. Align the
top back slot of assembly
B
with
the top back slat. Align the
remaining slats and use a mallet
to start the slat tenons into the
frame, leaving them slightly out.
Insert the front and rear sling rails
(
E
&
F
) and the front bottom
spreader (
H
) into their respective
slots. Then complete the process
of seating the back slats into the
frames so all tenons are fully
seated in their slots.
H
F
E
A
B
G
Please read entire instruction
before beginning
For E & F , the small board faces the
inside of the seat with its overhanging
end toward the armless side of the chair.
3 PB-1608 Assembly

H
F
E
A
B
G
f
b
3.00 3.00
a
KEEP FLUSH WITH TOP OF FRAME
c
C
D
h
i
(2) 1-3/4" screws (
b) are used on
each end of
E
,
F
&
H
.
6.
Insert sling spacer
D
into the seat frame as
shown at left. Be sure it is pushed against the
back of the seat. Install (6) hardware
c
to hold it
in place. Insert the seat sling (
C
) into the seat
frame. It should drop into the frame with minor
pressure applied to the frame sides.
5.
Screw in the back seat slats using (12) hardware
a
.
Start at the top, making sure the top of the slat is flush
to the top of the chair frame. Then work your way
down to the remaing two slats. For reference, slats are
spaced 3" from the bottom of one to the top of the
next. While looking at the back, install the remaining
(1) hardware
d
. This will require the larger end of bit
e
.
3.
Using the 6" torx bit (hardware
g
),
screw the (12) 1-3/4" screws (
b
) into
the bottom spreader (
H
) and sling
rails (
E
&
F
). When tight, the ends of
the spreader and rails should be flush
to the two side frame assemblies.
4.
Before flipping the chair to it's feet,
install the (4) leveling mounts
(hardware
f
) by threading them into the inserts
located at the four corners on the
bottom of the chair.
Optional:
If you wish to physically connect multiple
pieces of furniture together, use the included plates
and 1-1/4" screws (
h
&
i
) as shown at left. Connect
plates to the inside faces of the front and back legs
allowing approximately 1-1/2" of the plate to protrude
from the side of the chair. Then move the next
furniture piece into place and fasten the plates to it.
4 PB-1608 Assembly