Bristan VAC BAS C MT (D4) Wiring diagram

4
1
Pack Contents
Installation Instructions
& User Guide
1.0
5.0
Pressure
BAR
0.2
4.0
2.0 3.0
Pressure
BAR
1.0
5.0
0.2
4.0
2.0 3.0
Specifications
Maximum Static Pressure: 10.0 bar
Inlet Water Temperature Inlet Connections
Min: 0.2 bar Max: 5.0 bar
Dynamic Water Pressure
Tools You’ll Need
Prior to Installation
Phillips Screwdriver Adjustable Spanner Hexagonal Keys
Installation
Please leave these instructions
with the end user
Product code: VAC BAS C MT (D4)
All products manufactured and supplied by Bristan are safe
provided they are installed, used correctly and receive regular
maintenance in accordance with these instructions.
This product has been tested to the Water Regulations Advisory
Scheme (WRAS) and satisfies the requirements of the Water
Supply (Water Fittings) Regulations 1999 and current bylaws.
For full Installation Requirements & Notes (IRN)
please visit wras.co.uk/directory.
We recommend isolation valves to be fitted to the inlet water
supplies to ensure ease of future maintenance.
Before installing these taps the water supply must be thoroughly
flushed in order to remove any swarf, solder etc.
This product must not be modified in any way as this will
invalidate the guarantee.
2
Fit the mixer body to
the basin using the
‘C’ plate fixing kit.
Place the washer
over the hole in the
basin and feed the
mixer body and tails
through.
Place the washer and waste body plate
onto the horizontal arm. Screw the waste
body plate onto the lower waste body.
Push the vertical
rod through the
back of the basin
tap.
Connect the rods
using the pop up
connector. Tighten
screws to secure.
Fit the pop up waste,
with the flat washer
below and the shaped
washer above the basin.
3
M12 x 15mm
Copper Tails
5 6
60°C
65°C
Max
80°C
5°C
25°C
Cold Water Supply
Min: 5°C Max: 25°C
Hot Water Supply
60-65°C
recommended
80°C
Maximum
To replace any spare parts
for your tap, why not
scan the QR Code or
visit www.bristan.com
and search for your product.
Spare Parts
x1
IMPORTANT
Turn on water
supply for a few
minutes and check
all joints and
connections for
any leaks.
REMEMBER
Hot on the
left, cold on
the right!
TIP
Prefit mixer
to the basin
before
fitting.
Once secured to
the basin, connect
the hot and cold
water supplies to
the threaded tails.
x2
x1
x1
x1
x1
1x

At Bristan, we want to make things as easy as possible for our customers.
That’s why we oer solid guarantees on all our products, eective from the date of purchase,
to give you peace of mind.
To start your free guarantee simply scan the QR code and register your product.
Alternatively visit www.bristan.com/register to register your product via a computer.
For full guarantee terms and conditions visit www.bristan.com/guarantees.
Operation General Cleaning
Troubleshooting
Notes
Symptom Cause Remedy
No flow or
low flow
rate
Partially closed isolation valve. Open isolation valve.
Instantaneous water heater cycles on
and o as flow rate or pressure is too
low.
Increase water flow rate or pressure through system.
Head of water is below the
minimum distance required.
Refer to specification for minimum distance required.
Hot or cold water being drawn o
elsewhere causing pressure changes or
instantaneous boiler temperature
changes.
Do not use other water outlets when using the taps.
Airlock or partial blockage in the supply
pipework.
Flush through pipework to ensure removal of debris
and any airlocks.
Water
dripping
from taps
This is normal for a short time after using
the taps.
This is caused by residual water tension, the build up
of water in the tap body.
If water continues to drip,
possibly due to the ceramic disc valves
Remove valves and clean, refer to 'Maintenance'
section before starting any maintenance.
Taps do not
turn on
Closed isolation valve. Open isolation valve.
Mains water supply turned o. Turn on mains water supply.
Please use this space for any notes you or your installer may have regarding the
installation/plumbing of this product.
Bristan products are made from premium
materials, with hand polishing and
electroplated finishes.
Your taps or shower should be regularly
cleaned with warm water, a mild pH-neutral
liquid soap, and polished with a soft cloth.
Any residues from soap, toothpaste,
shampoos and shower gels can cause
blemishes if not rinsed o straight after use.
Household bleaches and cleaners contain
harsh chemicals and may damage the
surface finish. Avoid using abrasive cloths,
scouring pads, scrub sponges, steel wool
or anything similar.
Some surfaces such as nickel and pewter
may be aected by the dye found in some
cloths, so it is also important to avoid
hanging cloths on spouts.
3
6
2
1
5
4
Maintenance - Cartridge Cleaning
Remove the
cap from the
handle
Pull the rod up
to seal the plug.
Push it down to
release.
On
On
Remove the
screw from the
handle
Remove tha handle
from the tap
Adjust the friction for
the waste mechanism
by using the waste cap
body.
To set the plug
height adjust
the waste rod,
operating rod,
connecting
bracket and the
screw.
Unscrew the valve
using an adjustable
spanner.
Rinse with water
and replace valve,
shroud, spline
adaptor, screw
and handle.
Replace valve,
handle, screw and
cap.
Adjusting the Waste
Place cartridge
in a suitable
solution and
soak until
fully de-scaled.