Bullard 88VX Series User manual

TM
88VXTM Series Airline Respirator
User Manual
The Bullard 88VX Series airline respirators, when properly
used, provide a continuous flow of air from a remote air
source to the respirator wearer. 88VX Series respirators
offer protection from airborne contaminants that are not
immediately dangerous to life or health (IDLH), or that do
not exceed concentrations allowed by applicable OSHA,
EPA, NIOSH, ACGIH, or other regulatory standards and
recommendations.
88VX Series airline respirators are approved by NIOSH
(TC-19C-293 Type C and CE) to provide respiratory
protection in general purpose applications including heavy-
and light-duty abrasive blasting, andType C and CE painting
applications. The protective helmet meets ANSI Standard
Z89.1-1997 Type 1 Class C requirements for protective
headwear for industrial workers. The cape is designed to
protect the worker’s body from abrasive rebound.
88VX Series respirators are compatible with breathing air
sources such as breathing air compressors or Bullard
Free-Air®Pumps. Bullard offers the appropriate approved
breathing tube assembly and air supply hose to connect
the 88VX Series respirator to these breathing air sources.
88VX Series respirators are approved by NIOSH for use
with optional climate control devices offered by Bullard.
Read all instructions and warnings before using this respirator. Save this manual for future reference. Failure to follow
these instructions could result in death or serious injury.
WARNING
Approval Label .......................................................... 2,3
Component Concept .................................................... 4
Warnings .................................................................... 5, 6
Cautions/Limitations....................................................7
Operations
Protection ........................................................................ 7
Breathing Air Requirements ........................................ 7, 8
Breathing Air Pressure .................................................... 9
Breathing Air Pressure Table .......................................... 9
Typical Breathing Air Source and Respirator
Configurations ..................................................................10
Respirator Assembly
Sizing the Headband ...................................................... 11
Installing Headband into Inner Shell ............................ 12
Attaching Cape to Helmet .............................................. 12
Installing Breathing Tube Assembly into Respirator
Helmet ............................................................................ 12
Using Climate Control Devices ...................................... 12
Respirator Use
Donning ............................................................................13
Doffing ..............................................................................13
Inspection, Cleaning, and Storage
Cape ................................................................................ 14
Headband and Chin Strap .............................................. 14
Helmet ............................................................................ 14
Lenses and Window Frame Gasket ................................ 14
Breathing Tube Assembly .............................................. 15
Air Supply Hoses ............................................................ 15
Storage ............................................................................ 15
Parts and Accessories for 88VX Series Airline
Respirators .............................................................. 16-18
Return Authorizations ............................................ 19
Table of Contents

TM
Bullard
1898 Safety Way
Cynthiana, KY 41031-9303
877-BULLARD (285-5273)
Model 88VX Series
Type C and CE Continuous Flow Supplied-Air Respirator
Approved Only in the Following Configurations:
ALTERNATE FLOW CONTROL DEVICE
ALTERNATE HOOD
ASSEMBLIES
TC–PROTECTION
1
MODEL
RESPIRATOR COMPONENTS
ALTERNATE CAPE
ASSEMBLIES
19C-293 SA/SB/CF 88VX
88VX SERIES
HOODS
88VXA 88VXB
88VXC
88VXD
88VXE
88VXF
46VX 13VX 21VX 36VX
36XLVX
4616VX 1316VX
F30
F30B
F30S
F31 F32 F33 F34 F35
F35B
F35S
F37 F38 F40
F40B
F40S
F41 F42 F43 F44 F47 F48
AC100030
AC100030B
AC100030S
AC100031 AC100032 AC100033 AC100034 AC100037 AC100038
HC240030
HC240030B
HC240030S
HC240031 HC240032 HC240033 HC240034 HC240037 HC240038
DC5040
DC5040B
DC5040S
DC5041 DC5042 DC5043 DC5044 DC5047 DC5048
FRIG2000
XXXXX
X
XXXX
XXXX
X
X
XXX X
X
XXXXX
XXXX
X X X
XXXXX
X
X
X
X
X
X
X
XX
XXXXXXXXX
XX
XX
X
X
1. Protection
CF - Continuous Flow SA - Supplied Air SB - Supplied Air Abrassive Blast
2. Cautions and Limitations
B. Not for use in atmospheres immediately dangerous to life or health.
C. Do not exceed maximum use concentrations established by regulatory standards.
D. Airline respirators can be used only when respirators are supplied with respirable air
meeting the requirements of CGA G-7.1 Grade D or higher quality.
E. Use only the pressure ranges and hose lengths specified in the User’s instructions.
J. Failure to properly use and maintain this product could result in death or serious injury.
M. All approved respirators shall be selected, fitted, used, and maintained in accordance
with MSHA, OSHA, and other applicable regulations.
N. Never substitute, modify, add, or omit parts. Use only exact replacement parts in the
configuration as specified by the manufacturer.
O. Refer to user’s instructions, and/or maintenance manuals for information on use and
maintenance of these respirators.
Approval Label
2

88VX Series Airline Respirator
User Manual
Approval Label
3
ALTERNATE AIR HOSE ACCESSORIES
CAUTIONS
AND
LIMITATIONS
2
BCDEJMNO
HC240038
DC5040
DC5040B
DC5040S
DC5041 DC5042 DC5043 DC5044 DC5047 DC5048
FRIG2000
FRIG2000B
FRIG2000S
54513 54512 54511 54510
5454 5458
5457GOV
5457LOMAC
5457
5454LOMAC
5454GOV
46915LOMAC
46919 46918
4696FM
46928FF
46917FM
46917FF
46917
46916FF
46916FS
46915 46913
4696 4695
V2050STSHUTOFF V2025STSHUTOFF
V2025ST V2010ST V2050ST
V20100STSHUTOFF
V20100ST
V55033FS
V55033GRN
V52533FF
V52533FS
V52533
V55030GRN
V55031 V55030 V55033 V55032
V2531
V52530
V52530GREEN
V52532
V55033FF
DC70ML
DC70XLXXL
HS
B461B
P771B
P771040 P771020
B461040
P771R
B771R020
P771D015
88VXLC
7714
XXXXX
XX
XX
X
X X
XXXX
XX
XX
XXX
X
XX
X
XXX
X
XXXXXXX
X
XXXX
XXXX
X
X
XXX X X
XXXXX
XX
X
X
XXX X
X
XXXX

TM
Component Concept
4
Clean Breathable Air Source
Supplying Grade “D”or Higher Air Quality
(See Breathing Air Requirements on page 7)
Component Concept
The Bullard 88VX Series airline respirators consist of
three components (Figure 1): respirator helmet
assembly, breathing tube assembly, and air supply hose.
All components must be present and properly assembled
to constitute a complete NIOSH approved respirator.
Respirator Helmet
with Breathing Tube
➀
Belt
Cape
➁
Flow Control
Device
Air Supply Hose
➃
Inner Shell
Suspension
Inner and Outer
Window Lenses
Chin Strap
Cape
➤
Figure 1
Failure to use complete NIOSH approved Bullard
components and replacement parts voids approval of
entire assembly. Basic parts are listed on the NIOSH
Approval Label on page 3. Failure to follow these
instructions could result in death or serious injury.
WARNING
➂

88VX Series Airline Respirator
User Manual
Warning
5
1. This respirator, when properly fitted and used, in conjunction with adherence to OSHA regulations and industry
standards, will provide a reasonable degree of protection to the wearer. The respirator significantly reduces, but
may not totally eliminate, the breathing of contaminants depending on the work practices involved. Where
concentrations of contaminants are excessive, respirator wearers may obtain a higher level of protection from a
valve-operated, pressure demand airline respirator or a pressure demand, self contained breathing apparatus
(SCBA) respirator. At this time there are no side by side field studies for comparison. However, OSHA does assign
higher protection factors to these groups of respirators. Ideally, the employer should measure concentrations inside
the breathing zone on a periodic basis to ensure that the wearer is receiving adequate protection.
2. Before using this respirator, Federal Law requires that the employer shall identify and evaluate the respiratory
hazard(s) in the workplace, and that this evaluation shall include a reasonable estimate of employee exposures to
respiratory hazard(s) and an identification of the contaminant’s chemical state and physical form. Do not exceed
maximum use concentrations established by OSHA, EPA, NIOSH, ACGIH, or other regulatory standards.
3. Improper respirator use may damage your health and/or cause your death. Improper use may also cause certain
life threatening delayed lung diseases such as silicosis, pneumoconiosis, or asbestosis.
4. DO NOT wear this respirator if any of the following conditions exist:
- Atmosphere is immediately dangerous to your life or health (IDLH),
- You CANNOT escape without the aid of the respirator,
- Atmosphere contains less than 19.5% oxygen,
- Work area is poorly ventilated,
- Unknown contaminants are present, or
- Contaminant concentrations are in excess of regulations or recommendations (as described in item 2 above).
5. DO NOT wear this respirator until you have passed a complete medical evaluation (perhaps including a lung x-ray)
conducted by qualified medical personnel, and have been trained in the respirator’s use, maintenance, and
limitations by a qualified individual (appointed by your employer) who has extensive knowledge of Bullard 88VX
Series respirators.
6. DO NOT modify or alter this respirator in any manner. Use only NIOSH approved 88VX Series components and
replacement parts manufactured by Bullard for use with this respirator.
Failure to use NIOSH-approved Bullard components and replacement parts such as lenses, hoses, flow control
devices, capes, and climate control devices, voids NIOSH approval of the entire respirator, invalidates all Bullard
warranties, and could cause death, serious injury, lung disease, or exposure to other hazardous or life threatening
conditions.
7. Inspect all components of this respirator system daily for signs of wear, tear, or damage that might reduce the
degree of protection originally provided.
Immediately replace worn or damaged components with NIOSH approved Bullard 88VX Series components or
remove the respirator from service. (See INSPECTION, CLEANING, AND STORAGE section on pages 14-15 for proper
maintenance of 88VX Series respirators.)
8. Be certain your employer has determined that the breathing air source provides at least Grade D breathable air.This
respirator must be supplied with clean breathable air at all times.
9. Do not connect the respirator’s air supply hose to nitrogen, oxygen, toxic gases, inert gases, or other unbreathable,
non-Grade D air sources. To prevent this, the employer shall use airline couplings used for this respirator that shall
be incompatible with outlets for other gas systems, as required by OSHA regulation 29 CFR 1910.134 (i) (8). Check
the air source before using the respirator. Failure to connect to the proper air source could result in death or serious
injury.
10. Do not use this respirator in poorly ventilated areas or confined spaces such as tanks, small rooms, tunnels, or
vessels unless the confined space is well ventilated and the contaminant concentrations are below the upper limit
recommended for this respirator. In addition, follow all procedures for confined space entry, operation and exit as
defined in applicable regulations and standards, including 29 CFR 1910.146.
(Continued on Page 6)
WARNING

TM
Warning
6
11. If you have any questions concerning the use of this respirator, or if you are not sure whether the atmosphere you
are working in is immediately dangerous to life or health (IDLH), ask your employer. All instructions for the use and
care of this product must be supplied to you by your employer as recommended by the manufacturer and as required
by Federal Law (29 CFR 1910.134).
12. Do not use this respirator for underwater diving.
13. Leave work area immediately if:
-Any respirator component becomes damaged.
-Airflow into respirator stops or slows down.
-Air pressure gauge drops below the minimum specified in the Breathing Air Pressure Table in the 88VX Series User
Manual.
-Breathing becomes difficult.
-You become dizzy, nauseous, too hot, too cold, or ill.
-You taste, smell, or see contaminants inside the respirator hood.
-Your vision becomes impaired.
14. Historically, the incidence of disease from overexposure to toxic substances almost always occurs because the OSHA
regulations and industry standards applicable to the work practices involved are not followed. It is, therefore,
imperative that the employer acquaint itself with and follow all of these standards and regulations. REMEMBER:
-Respiratory protection is but one component of safe work practices. To minimize the chances of overexposure, all
safety regulations and standards must be followed; and
-Respiratory protection is the last line of defense to be employed. The employer must first eliminate or minimize the
levels of toxic substances in the work place by accepted engineering control measures. Assuming the employer and
the wearer do their part, this respirator should provide the wearer with an adequate degree of protection.
WARNING
(Continued from Page 5)

88VX Series Airline Respirator
User Manual
Cautions and Limitations/Operations
7
Cautions and Limitations
B. Not for use in atmospheres immediately dangerous to
life or health.
C. Do not exceed maximum use concentrations established
by regulatory standards.
D. Airline respirators can be used only when respirators
are supplied with respirable air meeting the
requirements of CGA G-7.1 Grade D or higher quality.
E. Use only the pressure ranges and hose lengths specified
in the instruction manual.
J. Failure to properly use and maintain this product could
result in death or serious injury.
M.All approved respirators shall be selected, fitted, used,
and maintained in accordance with MSHA, OSHA, and
other applicable regulations.
N. Never substitute, modify, add, or omit parts. Use only
exact replacement parts in the configuration as
specified by the manufacturer.
O. Refer to users instructions, and/or maintenance
manuals for information on use and maintenance of
these respirators.
For technical assistance call or write:
Bullard
1898 Safety Way
Cynthiana, KY 41031-9303
Toll free: 877-BULLARD (285-5273)
Phone: [phone]
Fax: [phone]
Operations
Protection
Respiratory
This respirator is NIOSH approved (TC-19C-293) as a Type
C and CE respirator. It can be worn for general purpose
applications, including heavy and light-duty abrasive
blasting, and spray painting.
This respirator is not approved for use in any atmosphere
immediately dangerous to life or health (IDLH), or from
which the wearer cannot escape without the aid of the
respirator.
Head
88VX Series respirators meet ANSI Standard Z89.1-1997
Type 1 Class C requirements for protective headwear for
industrial workers. The helmet is designed to provide
limited head protection by reducing the force of falling
objects striking the top of the helmet.
Face
The respirator’s inner window meets ANSI Z87.1-1989
requirements for face protection. It provides limited face
protection from flying particles or spray of hazardous
liquids, but is not shatterproof.
Eyes
88VX Series respirators DO NOT provide eye protection.
Wear approved safety glasses or goggles at all times.
Ears
88VX Series respirators DO NOT provide hearing
protection. Use properly fitted earmuffs, earplugs or other
protection when exposed to high noise levels.
Breathing Air Requirements
Air Quality
Respirable, breathing air must be supplied to the point-of-
attachment of the approved Bullard air supply hose. The
point-of-attachment is the point at which the air supply
hose connects to the air source. A pressure gauge attached
to the air source is used to monitor the pressure of air
provided to the respirator wearer (Figure 2, and Figure 3,
Page 10).
Supplied breathing air must AT LEAST meet the
requirements for Type 1 gaseous air as described in the
Compressed Gas Association Commodity Specification G-
7.1 (Grade D or higher quality), and as specified by Federal
Law 42 CFR, Part 84, Subpart J, 84.141(b) and 29 CFR
1910.134(i).
WARNING
This respirator MUST be supplied with clean, breathable
air, Grade D or better, at all times. This respirator does
NOT purify air or filter out contaminants. Failure to
follow these instructions could result in death or
serious injury.
Figure 2
Air Supply
Hose
Respirator
Grade “D”
Breathable
Air Source
Point-of-
Attachment*
Pressure
Gauge
*Use either a V13 hose-to-hose pipe adapter or a quick-
disconnect coupler to attach the air supply hose.

TM
Operations
8
The requirements for Grade D breathable air include:
Oxygen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.5-23.5%
Hydrocarbons (condensed)
in mg/m3 . . . . . . . . . . . . . . . . . . . . . . . . . . 5 mg/m3 max.
Carbon monoxide. . . . . . . . . . . . . . . . . . . . . . . 10 ppm max.
Carbon dioxide . . . . . . . . . . . . . . . . . . . . . . 1,000 ppm max.
Odor . . . . . . . . . . . . . . . . . . . . . . . . Lack of noticeable odor
No toxic contaminants at levels that make air unsafe
to breathe.
Contact the Compressed Gas Association (1725 Jefferson
Davis Hwy, Arlington, VA 22202) for complete details on
Commodity Specification G-7.1.
Air Source
Locate the source of supplied air whether it is an air
compressor or an ambient air pump, such as a Bullard
Free-Air pump, in a clean air environment. Locate the air
source far enough from your work site to ensure the air
remains contaminant-free. Always use an inlet filter on
your air source.
Use suitable after-cooler/dryers, filters, carbon monoxide
monitors and alarms, like the Bullard CAC01 Alert-1™CO
monitor, as necessary to assure clean, breathable air at all
times.
The air should be regularly sampled to be sure that it
meets Grade D requirements.
Breathing Air Pressure
Air pressure must be continually monitored at the point-of-
attachment while operating this respirator. A reliable air
pressure gauge must be present to permit you to
continually monitor the pressure during actual respirator
operation.
The Breathing Air Pressure Table (page 9) defines the air
pressure ranges necessary to provide 88VX Series
respirators with a volume of air that falls within the
required range of 6-15 cfm or 170-425 lpm (Ref. 42 CFR,
Part 84, Subpart J, Table 8).
Make sure you understand the information in the Breathing
Air Pressure Table before using this respirator.
1. Determine the type of air source you are using (column
1), then find your flow control valve/climate control
device (column 2).
2. Be sure your Bullard air supply hose(s) (column 3) is
approved for use with your flow control valve/climate
control device.
3. Determine that your Bullard air supply hose is within the
approved length (column 4).
4. Make sure you have not exceeded the maximum number
of hose sections (column 5).
5. Set the air pressure at the point-of-attachment within
the required pressure range (column 6) for your flow
control valve/climate control device, and air supply hose
type and length. Accurate pressure readings can only be
attained when air is flowing into the respirator.
NIOSH approved Bullard air supply hose(s) MUST be used
between the breathing tube connection fitting on the
wearer’s belt and the point-of-attachment to the air supply
(Figure 3, Page 10).
NIOSH approved Bullard quick-disconnect fittings MUST be
used to connect V5 or V20 hose lengths together. When
connecting lengths of V10 hose, only use Bullard V11 hose-
to-hose adapters. Secure connection(s) until wrenchtight
and leakfree. Total connected hose length and number of
hoses MUST be within the ranges specified on the
Breathing Air Pressure Table (Page 9) and the respirator’s
NIOSH approval label (Page 3).
The breathing tube connection fitting MUST be secured to
the belt that is supplied with this respirator. Securing the
air entry connection fitting helps prevent the air supply
hose from snagging, disconnecting or pulling the
respirator helmet off your head.
WARNING
Failure to supply the minimum required pressure at
the point-of-attachment for your hose length and type
will reduce airflow and could result in death or serious
injury.

88VX Series Airline Respirator
User Manual
Breathing Air Pressure Table
9
Breathing Air Pressure Table
This table defines the air pressure ranges necessary to provide 88VX Series respirators with a volume of air that falls within the required range of
6-15 cfm or 170-425 lpm according to U.S. Government regulations (42 CFR, Subpart J, 84.150,Table 8).
1234 5 6
Flow Control Valve/ Air Supply Air Supply Maximum Number Required Pressure
Air Source Climate Control Device Hose Hose Length (feet) of Hose Sections Range (psig air)
Stationary F30, F30B, F30S, F31, F32, V10 25 1 14-15
or Portable F33, F34, F37, F38 50 2 15-18
Air Compressor 100 3 19-24
150 4 23-29
200 5 25-34
250-300 5 31-39
V5 25 1 12-18
50 2 19-23
F40, F40B, F40S, F41, F42, V10 25 1 22-25
F43, F44, F47, F48 50 2 24-27
100 3 27-32
150 4 30-37
200 5 33-40
250-300 5 38-45
V5 25 1 22-26
50 2 25-30
AC100030, AC100030B, V10 25-50 2 55-65
AC100030S, AC100031, 75-150 3 60-70
AC100032, AC100033, 175-300 5 65-75
AC100034, AC100037,
ACC100038 V5 25 1 55-65
50 1 56-69
DC5040, DC5040B, V10 50 2 48-52
DC5040S, DC5041, 100 3 59-63
DC5042, DC5043, 150 3 68-72
DC5044, DC5047, 200 3 80-84
DC5048 250 3 85-92
300 5 90-98
V5 25 1 53-57
50 2 67-71
HC240030, HC240030B, V10 25 1 61-63
HC240030S, HC240031, 50 2 63-65
HC240032, HC240033, 100 3 68-70
HC240034, HC240037, 150 4 73-75
HC240038 200 4 77-79
250 5 80-82
300 5 84-86
V5 25 1 65-66
50 1 68-69
Bullard F35, F35B, F35S V20 50 1 4-6
Free-Air®100 2 6-8
Pumps 200 2 10-15
300 3 13-18
Frigitron 2000 V20 50 1 16-22
Frigitron 2000B 100 2 18-25
Frigitron 2000S 200 2 22-30
300 3 25-34

TM
10
Typical Breathing Air Source and Respirator Configurations
Figure 3
Point-of-Attachment
The point -of-attachment is the point at which the air supply
hose connects to the air source. A pressure gauge attached to
the air source is used to monitor the pressure of air provided
to the respirator wearer.
Air Source/Respirator Configurations
Bullard 88VX Series
Airline Respirator
Point-of-Attachment
Point-of-Attachment
Bullard Free-Air®Pump
Grade D Breathing Air
Cylinder System
Compressed Breathing Air System
Breathing Air Compressor
with storage tank
Suitable After-Cooler/Dryers with filters and
carbon monoxide monitor as required
Bullard 41 Series
Airline Filter
Air Control System
Connection Fitting
Point-of-Attachment
Bullard Air Supply Hose

Respirator Assembly
Before assembling this respirator, read the warning labels on
the inside of the respirator cape and the helmet shell and this
manual in full.
Remove and read the warning card inserted between the
respirator’s two lenses.
Sizing the Headband
Before you can size the headband suspension, the cape and
headband must be removed from the helmet using the
following steps:
1. Open hinged window frame by lifting up on window latch.
2. Remove cape from helmet by lifting up on clamp and
disengaging cape from helmet groove (Figure 4).
3. Turn helmet upside down. To remove inner shell from
helmet, hook index finger into loop on back of inner shell.
Press thumb against helmet rim and pull loop toward front
of helmet, then pull up and away from helmet (Figure 5).
This releases inner shell.
4. Size the standard 88VXTG headband by squeezing top and
bottom edges of rear buckle together with your thumb and
forefinger. At the same time, decrease headband size by
sliding right hand portion of headband through buckle.
5. Place the headband on your head. Pull down allowing
headband to expand until it feels comfortable. Headband
automatically adjusts to your size and locks when you
release your grip (Figure 6).
6. Remove headband from your head.
NOTE
If using the optional 88VXRT ratchet
headband, refer to the instruction sheet
provided with the 88VXRT.
Adjusting Suspension for Vertical Fit
The headband may be raised or lowered in the front and/or
back by repositioning the hanger keys. Vertical adjustment
makes headband ride higher or lower on wearer’s head. It
also can adjust the tilt forward or backward.
1. Rotate hanger key 90°in either direction until hole in
hanger key aligns with post on headband. Pull key away
from headband. (Figure 7).
2. Move key to desired vertical position.
3. Rotate hanger key 90°toward headband until key locks in
place (Figure 7).
4. Repeat steps 1-3 for other hanger keys.
88VX Series Airline Respirator
User Manual
Respirator Assembly
11
Figure 5
Figure 6
Figure 7
Helmet Back of helmet
Helmet grove
Cape
Window latch
Top rim of cape
Window latch strike
Window frame
Cape cable
Table or workbench
Figure 4

TM
Respirator Assembly
12
Installing Headband into Inner Shell
1. Turn inner shell and headband suspension upside down.
2. Place headband inside shell with brow pad facing front
of shell.
3. Bending hanger keys at hinge, insert keys into
respective key slots. Push firmly until keys snap into
place (Figure 8).
4. Insert inner shell into helmet with front of shell tilted
down. Align round hole located at front of shell with
washer at inside front of helmet. Press back of shell into
helmet until it snaps in place.
Using the 20NC Chin Strap
1. Attach chin strap to inner shell by sliding chin strap
keyway slot over plastic head on button inside the inner
shell. Refer to 20NC chin strap installation instructions.
2. Put helmet on your head. Adjust chin strap length with
the plastic slide.
Optional Lens Covers
1. If desired, apply optional lens covers designed to
protect the respirator’s plastic lens. Apply 2-3 lens
covers at a time.
2. When lens becomes soiled, remove by pulling tab at
edge of lens cover to clear your vision.
Attaching Cape to Helmet
1. Place cape on table or workbench. (Figure 4, page 11)
2. With window frame open, place helmet on top of cape.
3. Line up the clamp on the cape with the front center of
the helmet (Figure 4, page 11).
NOTE
Installation is easiest when started at the
front of cape and helmet.
4. Ease cape rim completely into the groove along helmet
edge, working your way to the back. Be certain cape is
completely in place at every point along helmet’s bottom
edge.
5. Snap the clamp to tighten cable and hold cape snugly on
helmet, while ensuring the cape stays in the groove.
6. Close and latch window frame.
Installing Breathing Tube Assembly
onto Respirator Helmet
1. Connect breathing tube assembly to helmet by screwing
plastic hose connector to fitting located on the side of
the helmet. Turn clockwise to tighten (Figure 9).
NOTE
Do not remove foam from inside the
breathing tube.The foam helps reduce the
noise level of the incoming air.
Using Climate Control Devices
88VX Series respirators are approved by NIOSH for use
with five optional Bullard climate control devices: AC1000
Series, DC50 Series, HC2400 Series and Frigitron 2000
Series.
1. Follow the instructions supplied with your climate
control device.
2. Be sure to use only the 88VXBT with your climate control
device.
3. Screw nylon hose connector on end of breathing tube to
hose thread on climate control device.
4. Firmly tighten hose connector by hand (Figure 10).
5. Lace belt supplied with respirator through belt loop
bracket on climate control device.
Figure 8
WARNING
Only use climate control devices manufactured by
Bullard. Substituting other climate control devices will
void the NIOSH approval and could result in death or
serious injury.
Figure 10
Figure 9

88VX Respirator Use/Donning/Doffing
13
88VX Respirator Use
Donning
Before using your 88VX Series respirator, complete the
assembly instructions given on pages 11-12. Before
putting on respirator, make sure there is no dirt, dust, or
contaminants inside the helmet.
1. Connect the Bullard air supply hose that is part of the
NIOSH approved assembly to the air source supplying
Grade D breathing air. Turn on the breathing air source.
2. With air flowing, connect breathing tube assembly to air
supply hose. Connect quick-disconnect fitting on
breathing tube assembly to quick-disconnect coupler on
air supply hose. Once fitting is secured, release coupling
sleeve to lock fittings together. Pull on both hoses to
make sure they are attached securely.
3. Adjust air pressure at point-of-attachment (Figure 2,
Page 7) to within the approved pressure range on the
Breathing Air Pressure Table (Page 9) for approved
pressure ranges.
4. With air still flowing, lower 88VX Series respirator
helmet onto your head for a comfortable fit.
5. Position headband for a comfortable fit. See instructions
on pages 11 and 12 for proper headband sizing.
6. Pull elastic chin strap under your chin and adjust for a
secure and comfortable fit. The chin strap will help
balance the helmet and should be worn at all times.
7. Be sure that the knitted inner neck cuff fits snugly
around your neck to help provide a barrier to airborne
contaminants.
8. With breathing tube assembly attached to the helmet,
fasten belt around waist or hips and adjust for comfort.
9. Pull respirator cape around your body and secure sides
by connecting the snap hooks. If using the Golden Gate
cape, first secure the ties that connect in back, then in
front. If using the Hibernia parka, tighten belt at waist.
10. Recheck air pressure and adjust if necessary.
11. With air still flowing into your respirator, you are now
ready to enter work area.
NOTE
OSHA respirator regulations do not
require fit testing of supplied air hoods
and helmets.
Doffing
When finished working, leave work area wearing
respirator and with air still flowing. Once outside
contaminated area, remove respirator and then disconnect
the air supply hose using the quick-disconnect fittings.
NOTE
If using V20 Series (1/2" I.D.) air supply
hose, the quick-disconnect coupler does
not have a shut-off valve. Therefore, air
will continue to flow freely after
disconnecting hose from respirator.
WARNING
Do not put on or remove this respirator in a hazardous
atmosphere. Do not remove this respirator in a
hazardous atmosphere except for emergency escape
purposes. Failure to follow these instructions could
result in death or serious injury.
WARNING
Leave work immediately if:
- Any respirator component becomes damaged.
- Airflow into respirator helmet stops or slows down.
- Air pressure gauge drops below the minimum
specified in the Breathing Air Pressure Table
(page 9).
- Breathing becomes difficult.
- You become dizzy, nauseous, too hot, too cold or ill.
- You taste, smell or see contaminants inside
respirator helmet.
- Vision becomes impaired.
Failure to follow these instructions could result in
death or serious injury.
WARNING
Do not leave respirator in work area. Respirable dust
contaminants can remain suspended in the air for
more than one hour after work activity ceases, even
though you may not see them. Proper work practice
requires you to wear the respirator until you are
outside the contaminated area. Failure to don, doff
and store the respirator outside of contaminated area
could result in exposure to contaminants. Failure to
follow these instructions could result in death or
serious injury.
Adjust neck cuff Always wear respirator in work area
88VX /Respirator Use/Donning/Doffing
13
88VXTM Series Airline Respirator
User Manual

Inspection, Cleaning and
Storage
Bullard’s 88VX Series respirators have a limited service
life. Therefore, a regular inspection and replacement
program must be conducted. Certain parts such as capes
and lenses must be replaced frequently.
The 88VX Series respirator and all component parts and
assemblies should be inspected for damage or excessive
wear, before and after each use, to ensure proper
functioning. Immediately remove the respirator from
service and replace parts or assemblies that show any sign
of failure or excessive wear that might reduce the degree
of protection originally provided.
Use only complete NIOSH approved Bullard 88VX Series
components and replacement parts on this respirator.
Refer to parts list (Pages 16-17) for correct part numbers.
Since respirator use and the quality of maintenance
performed vary with each job site, it is impossible to
provide a specific time frame for respirator replacement.
As a general guideline, the 88VX Series respirator should
be replaced after two years of service or less.
This respirator should be cleaned and sanitized at least
weekly, or more often if subjected to heavy use.
Respirators used by more than one person must be
cleaned, inspected and sanitized after each use. If not
cleaned, contamination may cause illness or disease.
REMEMBER, THE AIR YOU BREATHE WILL NOT BE CLEAN
UNLESS THE RESPIRATOR YOU WEAR IS CLEAN.
Cape
Inspection
Remove the cape from the respirator helmet and inspect it
for rips, tears or damage from excessive wear that might
reduce the degree of protection originally provided.
Inspect the inner neck cuff for elasticity.
If you detect any of these signs, replace your cape
immediately or remove the respirator from service.
Cleaning
Machine wash the cape in cold or warm water using a
gentle cycle. Use a mild laundry detergent. Air-dry only.
After cleaning, carefully inspect the cape once again for
signs of damage.
Do not use volatile solvents to clean this respirator or any
parts and assemblies. Strong cleaning and disinfecting
agents, and many solvents, can damage the plastic parts.
Headband and Chin Strap
Inspection
Remove the headband suspension and chin strap from the
inner shell. Inspect the headband for cracks, frayed or cut
crown straps, torn headband or size adjustment slots, loss
of pliability or other signs of excessive wear. Check the
chin strap for loss of elasticity, cuts and cracked hanger
clips.
If damage is detected, replace parts immediately with
Bullard replacement parts or remove the respirator from
service.
Cleaning
The headband suspension and chin strap should be hand-
sponged with warm water and mild detergent, rinsed and
air-dried. After cleaning and before reassembling, once
again carefully inspect the parts for signs of damage.
Helmet
Inspection
Inspect the helmet and inner shell for nicks, gouges,
cracks, holes and any damage due to impact, rough
treatment or wear.
If damage is detected, replace parts immediately with
Bullard replacement parts or remove the respirator from
service.
Cleaning
The helmet, inner shell, and window frame should be hand-
sponged with warm water and mild detergent, rinsed and
air-dried.
After cleaning and before reassembling, once again
carefully inspect the helmet and parts for signs of damage
Lenses and Window Frame Gasket
Inspection
Be sure the plastic inner lens fits securely in the window
frame gasket. Remove any grit or dust from the gasket. Be
sure the plastic outer lens is installed underneath the
clamps on the back of the outer window frame. Inspect the
window frame gasket closely for cuts, wear or damage
that will prevent a proper seal against the inner faceshield
lens or the helmet window frame.
If damage is detected, replace parts immediately with
Bullard replacement parts or remove the respirator from
service.
Cleaning
To clean the lenses, hand-sponge with warm water and
mild detergent, rinse and air-dry.
TM
Inspection, Cleaning, and Storage
14
WARNING
Do not substitute any capes other than those
manufactured by Bullard. Substituting other capes will
void the NIOSH approval and could result in death or
serious injury.
WARNING
Do not use lenses other than those listed on the next
page. Substituting other lenses voids the NIOSH
approval. Use of non-Bullard lenses may allow
contaminants to enter the respirator and could result
in death or serious injury.
Your respirator cape may be
machine washed

NOTE
All Bullard lenses are stamped with the
appropriate Bullard part number
described below.
Bullard Lens Description Part No.
Inner lens for 88VX Series Respirators (oval). . . . . . 771B
Outer lenses for 88VX Series Respirators (oval). . . . . 771
Inner lens for 88VX Series Respirators
(rectangular) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461B
Outer lenses for 88VX Series Respirators
(rectangular) . . . . . . . . . . . . . . . . . . . . . . . 461, 461R, 771R
Breathing Tube Assembly
Inspection
Inspect the breathing tube for tears, cracks, holes, or
excessive wear that might reduce the degree of protection
originally provided. If any signs of excessive wear are
present, replace the breathing tube immediately or remove
the respirator from service.
Cleaning
To clean the breathing tube, hand-sponge with warm water
and mild detergent, being careful not to get water inside.
Rinse and air-dry. After cleaning, once again carefully
inspect breathing tube for signs of damage.
Air Supply Hose
Inspection
The starter and extension hose(s) should be inspected
closely for abrasions, corrosion, cuts, cracks and
blistering. Be sure the hose fittings are crimped tightly to
the hose so that air cannot escape. Make sure the hose has
not been kinked or crushed by any equipment that may
have rolled over it.
If any of the above signs are present or any other signs of
excessive wear are detected, replace the air supply
hose(s) immediately or remove the respirator from
service.
Cleaning
The air supply hose(s) should be hand-sponged with warm
water and mild detergent, rinsed and air-dried. Do not get
water inside the air supply hose. After cleaning, once again
carefully inspect air supply hose(s) for signs of damage.
Storage
After reusable respirator components have been cleaned,
dried and inspected, place them in a plastic bag or an
airtight container.
Store the respirator and parts where they will be protected
from contamination, distortion and damage from elements
such as dust, direct sunlight, heat, extreme cold, excessive
moisture and harmful chemicals.
88VX Series Airline Respirator
User Manual
Inspection, Cleaning, and Storage
15
CAUTION
Do not cut or remove foam that is inside the breathing
tube. The foam helps reduce the noise level of the
incoming air supply. It does not filter or purify your
breathing air. NIOSH has approved this respirator with
the foam in place. Failure to observe these
instructions may result in minor or moderate injury.
WARNING
Only use hoses that are NIOSH approved for use with
this respirator. Other hoses could reduce airflow and
protection, and expose the wearer to life threatening
conditions. Failure to follow these instructions could
result in death or serious injury.
Store in a clean place away from
contaminants

TM
Ordering Information
16
Parts and Accessories for 88VX Series Airline Respirators
88VX Series supplied-air respirators consist of four components: 1.) respirator helmet assembly with breathing tube, 2.)
cape, 3.) flow control device, and 4.) air supply hose. There are options for some components to fit customer
specifications. All components must be present and properly assembled, including a Bullard air supply hose, to constitute
a complete NIOSH approved respirator (Approval No. TC-19C-293, Type C and CE).
CATALOG CATALOG
NUMBER DESCRIPTION NUMBER DESCRIPTION
Parts for 88VX Series Respirators
88VXTG 4-point headband suspension with sizing posts
and Sportek®brow pad (25/pkg)
88VXRT 4-point headband suspension with Sure-Lock
ratchet sizing knob and Sportek brow pad (25/pkg)
20NC Elastic Chin Strap
99PL Inner shell/air plenum
88CK Breathing tube connector kit
88VXAK Oval door/Gasket/Latch Kit Assembly
88VXRAK Rectangular door/Gasket/Latch Kit Assembly
BFW Box Front Adapter Kit, complete
(for 88 and 88VX Series only)
77GLT Tempered Glass Lens for BFW
77LG Box Front Lens Gasket
G4613 88VXR Window Frame Gasket (rectangular)
G7713 88VXR Window Frame Gasket (oval)
88VXUGK 88VX Upgrade Kit:
Includes 88VXAK, 99PL, 88VXTG, 46VX and 88VXBT
Lenses and Mylar Covers
Lenses for 88VX Series (oval)
771B Inner Plastic Lens, .040" thick (25/pkg)
771(.040) Outer Plastic Lens, .040" thick (25/pkg)
771(.020) Outer Plastic Lens, .020" thick (50/pkg)
Lenses for 88VX Series (rectangular)
461B Inner Plastic Lens, .040" thick (25/pkg)
461 Outer Plastic Lens, .040" thick (25/pkg)
461R Outer Plastic Lens, .015" thick (50/pkg)
771R(.015) Outer Plastic Lens, .015" thick (50/pkg)
7714 Clear Mylar Lens Cover, Adhesive-Backed (25/pkg)
88VXLC Clear Mylar Lens Cover, Perforated-Edges
with pull tab (25/pkg)
Capes
46VX Tan Nylon Cape - 28" length
13VX Tan Nylon Cape - 38" length
21VX “Golden Gate”style -Tan Nylon Cape - 38" length
36VX Hibernia Parka -Tan Nylon Parka
with sleeves - 38" length
36XLVX Hibernia Parka - Tan Nylon Parka
with sleeves - 38" length, extra-large
Flow Control Devices (Includes Belt)
Adjustable Flow
EVX40 Breathing tube assembly - 1/4" Industrial
Interchange (steel) quick-disconnect fitting
AC100030 Air Conditioner - 1/4" Industrial Interchange (steel)
quick-disconnect fitting
Frigitron Air Conditioner - 1/2" Industrial Interchange (steel)
2000 quick-disconnect fitting, (for use with Bullard
EDP30 Free-Air pump)
HC240030 Hot/Cold tube - 1/4" Industrial Interchange (steel)
quick-disconnect fitting
DC5040 DUAL-COOL tube - 1/4" Industrial Interchange
(steel) quick disconnect fitting. Order DUAL-COOL
vest separately
Constant Flow
EVX30 Breathing tube assembly - 1/4" Industrial
Interchange (steel) quick-disconnect fitting
EVX35 Breathing tube assembly - 1/2" Industrial
Interchange (steel) quick-disconnect fitting
Dual-Cool Vest
DC70ML DUAL-COOL vest. Size: M/L. Order DUAL-COOL
tube separately.
DC70XLXXL DUAL-COOL vest. Size: XL/XXL. Order DUAL-COOL
tube separately.
CH60 Connector hose for use with DUAL-COOL
Replacement Parts for Breathing Tube
Assemblies
88VXBT Breathing tube only, with threaded hose connectors
4612 Belt, nylon webbing
F30 Constant flow control valve
1/4" Industrial Interchange (steel)
F35 Constant flow control valve,
1/2" Industrial Interchange (steel)
F40 Adjustable flow control valve,
1/4" Industrial Interchange (steel)
Air Supply Hose Kits
V10 Series Hoses (3/8" I.D.) for use with breathing
air compressors
4696 25-foot Starter hose with 1/4"
Industrial Interchange Q.D. coupler
46913 25-foot Starter hose with 1/4"
Schrader Q.D. coupler
46915 25-foot Starter hose with 1/4"
Snap-Tite Q.D. coupler
5454 25-foot Extension hose
5457 50-foot Extension hose
5458 100-foot Extension hose
V20 Series Hoses (1/2" I.D.) for use with
Free-Air Pumps
V2050ST 50-foot Starter/Extension hose with 1/2"
Industrial Interchange Q.D. coupler
V20100ST 100-foot Starter/Extension hose with 1/2"
Industrial Interchange Q.D. coupler
V5 Series Coiled Hoses for use with breathing
air compressors
V52530 25-foot Starter hose with 1/4"
Industrial Interchange Q.D. coupler
V55030 50-foot Starter hose with 1/4"
Industrial Interchange Q.D. coupler
V52531 25-foot Starter hose with 1/4"
Schrader Q.D. coupler
V55031 50-foot Starter hose with 1/4"
Schrader Q.D. coupler
V52532 25-foot Starter hose with 1/4"
Snap-Tite Q.D. coupler
V55032 50-foot Starter hose with 1/4"
Snap-Tite Q.D. coupler

88VX Series Airline Respirator
User Manual
Ordering Information
17
Quick-Disconnect Nipples
1/4" Industrial Interchange
S9841 With 1/4" Female NPT
V17 With 3/8" Female NPT
1/4" Schrader
S19432 With 1/4" Female NPT
S19433 With 3/8" Female NPT
1/4" Snap-Tite
S19442 With 1/4" Female NPT
S17651 With 3/8" Female NPT
Quick-Disconnect Couplers (Shut-off Type)
1/4" Industrial Interchange
V14 With 1/4" Female NPT
366254 With 3/8" Female NPT
366054 With 1/4" Male NPT
V15 With 3/8" Male NPT
1/4" Schrader
V18 With 1/4" Female NPT
S17603 With 1/4" Male NPT
S17601 With 3/8" Male NPT
1/4" Snap-Tite
V19 With 1/4" Female NPT
S17615 With 3/8" Female NPT
S17611 With 1/4" Male NPT
S17614 With 3/8" Male NPT
Quick-Disconnect Hose Adapters
V11 Hose-to-hose, 3/8" hose to 3/8" hose
V12 Hose-to-pipe, 3/8" hose to 1/4" pipe
V13 Hose-to-pipe, 3/8" hose to 3/8" pipe
To order replacement parts, contact your local Bullard
distributor or the Bullard Customer Service Department.
Bullard
1898 Safety Way
Cynthiana, KY 41031-9303
Toll Free: 877-BULLARD (285-5273)
Phone: [phone]
Facsimile: 859-234-6858
CATALOG CATALOG
NUMBER DESCRIPTION NUMBER DESCRIPTION
46VX
V5 Coiled Hose
V52530, V55030, V52531, V55031,
V52532, V55032
Air Supply Hose
5454, 5457, 5458,
V2050ST, V20100ST
99PL
AC1000
Frigitron 2000
88VXTG
88VXRT
20NC
88VXBT
MV2400 HC2400
88VXBT
88VXBT
13VX
21VX

TM
Ordering Information
18
Bullard
1898 Safety Way
Cynthiana, KY 41031-9303
877-BULLARD (285-5273)
Model 88VX Series
Type C and CE Continuous Flow Supplied-Air Respirator
Approved Only in the Following Configurations:
ALTERNATE FLOW CONTROL DEVICE
ALTERNATE HOOD
ASSEMBLIES
TC# PROTECTION
1
MODEL
RESPIRATOR COMPONENTS
ALTERNATE CAPE
ASSEMBLIES
19C-293 SA/CF 88VX
88VX SERIES
HOODS
88VXA 88VXB
88VXC
88VXD
88VXE
88VXF
46VX 13VX 21VX 36VX
36XLVX
4616VX 1316VX
F30
F30B
F30S
F31 F32 F33 F34 F35
F35B
F35S
F37 F38 F40
F40B
F40S
F41 F42 F43 F44 F47 F48
AC100030
AC100030B
AC100030S
AC100031 AC100032 AC100033 AC100034 AC100037 AC100038
HC240030
HC240030B
HC240030S
HC240031 HC240032 HC240033 HC240034 HC240037 HC240038
XXXXX
X
XXXX
XXXX
X
X
XXX X
X
XXXXX
XXXX
X X X
XXXXX
X
X
X
X
X
X
X
XX
XXXX X
1. Protection
CF - Continuous Flow SA - Supplied Air
2. Cautions and Limitations
B. Not for use in atmospheres immediately dangerous to life or health.
C. Do not exceed maximum use concentrations established by regulatory
standards.
D. Airline respirators can be used only when respirators are supplied with
respirable air meeting the requirements of CGA G-7.1 Grade D or higher
quality.
E. Use only the pressure ranges and hose lengths specified in the User’s
instructions.
J. Failure to properly use and maintain this product could result in death or
serious injury.
CATALOG
NUMBER DESCRIPTION
Adjustable Flow
F40B 1/4" Industrial Interchange (brass)
F40S 1/4" Industrial Interchange (stainless steel)
F41 1/4" Schrader
F42 1/4" Snap-Tite (steel)
F43 1/4" Snap-Tite (brass)
F44 1/4" Snap-Tite (stainless steel)
F47 1/4" Cejn
F48 1/4" Bayonet
Constant Flow
F30B 1/4" Industrial Interchange (brass)
F30S 1/4" Industrial Interchange (stainless steel)
F31 1/4" Schrader
F32 1/4" Snap-Tite (steel)
F33 1/4" Snap-Tite (brass)
F34 1/4" Snap-Tite (stainless steel)
F37 1/4" Cejn
F38 1/4" Bayonet
F35B 1/2" Industrial Interchange (brass)
F35S 1/2" Industrial Interchange (stainless steel)
Adjustable Climate Control Tubes
Cold Only Hot/Cold Dual-Cool Coupling Type
AC100030B HC240030B DC5040B 1/4" Industrial Interchange (brass)
AC100030S HC240030S DC5040S 1/4" Industrial Interchange (stainless steel)
AC100031 HC240031 DC5041 1/4" Schrader
AC100032 HC240032 DC5042 1/4" Snap-Tite (steel)
AC100033 HC240033 DC5043 1/4" Snap-Tite (brass)
AC100034 HC240034 DC5044 1/4" Snap-Tite (stainless steel)
AC100037 HC240037 DC5047 1/4" Cejn
AC100038 HC240038 DC5048 1/4" Bayonet
Other Available Flow Control Assemblies (Without Breathing Tube)

Ordering Information
19
Ordering Information
19
88VXTM Series Airline Respirator
User Manual
ALTERNATE AIR
HOSE ACCESSORIES
CAUTIONS
BCDEJMNO
FRIG2000B
FRIG2000S
54513 54512 54511 54510
5454 5458
5457GOV
5457LOMAC
5457
5454LOMAC
5454GOV
46915LOMAC
46919 46918
4696FM
46928FF
46917FM
46917FF
46917
46916FF
46916FS
46915 46913
4696 4695
V2050STSHUTOFF V2025STSHUTOFF
V2025ST V2010ST V2050ST
V20100STSHUTOFF
V20100ST
V55033FS
V55033GRN
V52533FF
V52533FS
V52533
V55030GRN
V55031 V55030 V55033 V55032
V2531
V52530
V52530GREEN
V52532
V55033FF
DC70ML
DC70XLXXL
HS
B461B
P771B
P771040 P771020
B461040
P771R
B771R020
X X
XXXX
XX
X
X X
XXXXXXX
X
XXXX
XXXX
X
X
XXX X X
XXXXX
XX
X
X
XXX X
X
XXXX
88VX Series Respirator Replacement Parts
771
771B 7714
771R
88VXLC
461B
461 or
461R
DC70ML
DC70XLXXL
CH60
DC5040
88VXBT
F35
4612
Breathing Tube Assembly Constant Airflow
EVX35
Breathing Tube Assembly Adjustable Airflow
EVX40
88VXBT
F40
4612
88BFW
771R
Kit 88VXAK Kit 88VXRAK

TM
Respiratory
Protection Fire and Rescue Safety
Head
Protection Thermal
Imaging
6080885603(1203)
Bullard
1898 Safety Way
Cynthiana, KY 41031-9303
Toll free: 877-BULLARD (285-5273)
Tel: [phone]
Fax: [phone]
www.bullard.com
Bullard GmbH
Hochkreuzallee 36
53175 Bonn-Bad Godesberg
Germany
Tel: [phone]
Fax: [phone]
ISO 9001
certified
©2003 Bullard. All rights reserved.
Bullard, Free-Air, Sportek, Dual-Cool, and Sure-Lock are
registered trademarks of Bullard.
“It’s your life and you’re worth it”and 88VX are
trademarks of Bullard.
Return Authorization
The following steps must be completed before Bullard will accept any returned goods. Please read carefully.
Follow the steps outlined below to return goods to Bullard for repair or replacement under warranty or for paid
repairs:
1. Contact Bullard Customer Support by telephone or in writing at:
Bullard
1898 Safety Way
Cynthiana, KY 41031-9303
Toll-Free: 877-BULLARD (285-5273)
Phone: [phone]
In your correspondence or conversation with Customer Support, describe the problem as completely as
possible. For your convenience, your coordinator will try to help you correct the problem over the phone.
2. Verify with your coordinator that the product should be returned to Bullard. Customer Support will provide
you with written permission and a return authorization number as well as the labels you will need to return
the product.
3. Before returning the product, decontaminate and clean it to remove any hazardous materials which may
have settled on the product during use. Laws and/or regulations prohibit the shipment of hazardous or
contaminated materials. Products suspected to be contaminated will be professionally discarded at the
customer’s expense.
4. Ship returned products, including those under warranty, with all transportation charges pre-paid. Bullard
cannot accept returned goods on a freight collect basis.
5. Returned products will be inspected upon return to the Bullard facility. Bullard Customer Support will
telephone you with a quote for required repair work which is not covered by warranty. If the cost of repairs
exceeds stated quote by more than 20%, your coordinator will call you for authorization to complete repairs.
After repairs are completed and the goods have been returned to you, Bullard will invoice you for actual
work performed.