burmeier Vertica-Homecare User manual

Instruction Manual
Care bed with stand-up function
Vertica-Homecare
Date: 2018-05-25
241335, v3

Instruction Manual for Vertica-Homecare Bed
Page 3
Care bed Vertica-Homecare: Control elements
1
Release slider; pull inward to fold down footboard (optional)
2
Velcro strap for securing the special mattress to the footboard
3
Patient handset
4
Release button for safety sides (1x each side)
5
Release slider for folding down the safety sides
6
Safety sides (on both sides)
7
Headboard, removable
8
Insert for lifting pole / infusion stand (covered, 2 items)
9
Wall deflection rollers (4 in total, one per corner)
10
Grab handles / side mattress guides for backrest
11
2x universal holder, sliding, on both sides (optional)
12
Lever, red, for adjustment / emergency lowering of backrest (CPR), both sides
14
Foot lever (both sides) for operating castor brakes or for steering
15
NURSE handset “Stand-up function”
16
Support rollers (automatically retracting for setting upright position)
17
Side panel; tiltable as far as mobilisation supports
18
Release button orange: for extending bed (activate both sides)
19
Release level grey: Tilting/proper engagement of mobilisation supports [17]
20
Footboard, removable; optional: fold-down to a linen holder or as a table
+removable
21
For fold-down footboard option: Pushbuttons (left and right) to release
footboard for removal
Advice:
In this instruction manual, numbers which appear in bold type and square
brackets [ ] refer to features described for the Vertica Homecare bed.
14
16
12
9
7
19
10
6
11
20
8
2
9
17
15
18
21
Optional feature:
Fold-down
footboard
1
4
5
3

Instruction Manual for Vertica-Homecare Bed
Page 4
Contents
1FOREWORD...................................................................................................................6
2GENERAL INFORMATION .............................................................................................7
2.1 Definition of the Groups of Persons Involved...................................................... 7
2.2 Safety Instructions ................................................................................................... 8
2.2.1 Explanation of the Safety Symbols Used.................................................. 8
2.2.2 Safety Information for the Operator ......................................................... 9
2.2.3 Safety Information for the User .................................................................. 9
2.3 Product Description .............................................................................................. 12
2.3.1 Intended Use .............................................................................................. 12
2.3.2 Use for the Intended Purpose .................................................................. 12
2.3.3 Contraindications ...................................................................................... 13
2.3.4 Side Effects.................................................................................................. 14
2.3.5 Special Features ........................................................................................ 14
2.3.6 Materials Used............................................................................................ 14
2.3.7 Structural Design........................................................................................ 15
3INITIAL SERVICE..........................................................................................................16
3.1 Checklist: Inspection by the User........................................................................ 17
3.2 Location Requirements ........................................................................................ 18
4OPERATION ................................................................................................................19
4.1 Moving and Braking the Bed .............................................................................. 19
4.2 Electric Drive System............................................................................................. 20
4.2.1 Special Safety Information on the Electrical Actuator System........... 20
4.2.2 Patient Handset ......................................................................................... 22
Sleep position ........................................................................................................ 22
4.2.3 NURSE Handset (Stand-Up Function)...................................................... 26
4.2.4 Battery Pack (Rechargeable Batteries) ................................................. 26
4.3 Stand-up function ................................................................................................. 28
4.3.1 General Description .................................................................................. 28
4.3.2 Safety Precautions for Stand-Up Function............................................. 28
4.3.3 NURSE Handset (Stand-Up Function)...................................................... 29
4.3.4 Preparing the Stand-Up Function............................................................ 30
4.3.5 Removing the Headboard / Footboard ................................................ 31
4.3.6 Activating Stand-Up Function ................................................................. 34
4.3.7 Using the Stand-Up Function.................................................................... 35
4.3.8 Using the Pivoting Footboard as a Table (Optional)............................ 36
4.3.9 Ending the Stand-Up Function................................................................. 37
4.4 Manual Adjustments............................................................................................. 38
4.4.1 Safety Information ..................................................................................... 38
4.4.2 Emergency Release of the Backrest (CPR) ........................................... 39
4.4.3 Bed Extension (Optional).......................................................................... 40
4.4.4 Extending the Mattress Base.................................................................... 41
1/8
5
4
7
6
3
11
10

Instruction Manual for Vertica-Homecare Bed
Page 5
4.5 Attachments .......................................................................................................... 43
4.5.1 Adaptor Sleeves for Patient Lifting Pole / Infusion Stands ................... 43
4.5.2 Grab Handle (Triangular Handle)............................................................ 44
4.5.3 Mains Cable Holder................................................................................... 45
4.5.4 Universal Holder (Optional) ...................................................................... 45
4.6 Safety Sides ............................................................................................................ 46
4.6.1 Safety Information for Safety Sides.......................................................... 46
4.6.2 MultiFlex Safety Sides (MSG)..................................................................... 47
5CLEANING AND DISINFECTION................................................................................ 49
5.1 General Information on Cleaning and Disinfection ........................................ 49
5.2 Cleaning and Disinfection Instructions .............................................................. 50
5.3 Instructions for the User and Expert .................................................................... 51
5.4 Cleaning and Disinfection Agents ..................................................................... 52
5.5 Handling Cleaning and Disinfection Agents .................................................... 53
6MAINTENANCE.......................................................................................................... 54
6.1 Servicing ................................................................................................................. 54
6.1.1 Service Interval........................................................................................... 54
6.1.2 Servicing Plan ............................................................................................. 55
6.2 Regular Safety Inspections on Care Beds ......................................................... 57
6.3 Replacement Parts ............................................................................................... 60
6.4 Service Address ..................................................................................................... 60
6.5 Replacement of Electrical Components .......................................................... 61
6.5.1 Safety Information ..................................................................................... 61
6.5.2 Terminal Assignments for Control Unit CB16 .......................................... 62
6.5.3 Replace Handset....................................................................................... 63
6.5.4 Replace Mains Cable ............................................................................... 63
6.5.5 Battery Replacement................................................................................ 64
6.5.6 RESET Control Unit CB16 ............................................................................ 65
6.5.7 Actuator Alignment................................................................................... 65
7TROUBLESHOOTING .................................................................................................. 68
7.1 Troubleshooting Guide......................................................................................... 68
8ACCESSORIES............................................................................................................ 70
9TECHNICAL DATA...................................................................................................... 71
9.1 Dimensions and Weights ...................................................................................... 71
9.2 Adjustment Options .............................................................................................. 71
9.3 Electrical Data ....................................................................................................... 71
9.4 Ambient Conditions .............................................................................................. 75
9.5 Technical Information on Electromagnetic Compatibility (EMC) ................. 75
9.6 Classification .......................................................................................................... 78
10 DISPOSAL INSTRUCTIONS.......................................................................................... 79
11 EC DECLARATION OF CONFORMITY........................................................................ 81

Instruction Manual for Vertica-Homecare Bed
Page 6
1Foreword
Dear Customer,
Burmeier has built this bed to give you the best possible help with the challenges
posed by nursing and caregiving. We passionately pursue the goal of developing
high-quality durable products. Our beds should make patients and residents feel
as safe and comfortable as possible during their stay in bed and also lighten the
workload of nursing and care staff. For this reason, all functions and electrical
safety are tested prior to delivery. Each bed leaves our factory in perfect
condition.
Correct operation and care are necessary to keep the bed in excellent condition
during long-term use. Please therefore read and observe these instructions
carefully. They will help you to put the bed into service for the first time and to use
it on a daily basis. This instruction manual contains all the information you will need
to make it as easy and safe as possible to control and handle this bed, both for
you as the operator and your users. It is a practical reference book and should be
kept close to hand at all times.
Even after you have purchased a bed, Burmeier is still on hand to help at any
time. We provide customised solutions in all matters relating to inspection and
maintenance, repair and process optimisation. You can contact our service
centre by phone at [phone] - 0.
We wish you and your users every success and satisfaction in caring for your
patients and residents.
Burmeier GmbH & Co. KG
Disclaimer
This product is not licenced for use on the North American market. This applies
particularly to the United States of America. The distribution and use of the care
bed in these markets, including through third parties, is prohibited by the
manufacturer.

Instruction Manual for Vertica-Homecare Bed
Page 7
2General Information
This instruction manual describes several different models of the Vertica-
Homecare bed.
It is possible that certain functions or features are described which are not
incorporated in your particular bed.
In the following text, the Vertica-Homecare bed will be referred to simply as the
bed.
2.1 DEFINITION OF THE GROUPS OF PERSONS INVOLVED
In this instruction manual, the following groups of persons are defined as:
Operator
An operator (e.g.: clinic, hospital, hospital administration) is any natural and legal
person with property rights to the Vertica-Homecare bed. The operator is
responsible for the safe operation of this medical device.
Users
Users (e.g.: medical specialists, nursing staff, doctors, carers, care workers) are
persons who, based on their training, experience or briefing, are qualified to
operate the bed on their own authority or to carry out work on it, or have been
instructed how to handle the bed. Furthermore, they can recognise and avoid
potential dangers and assess the clinical condition of the patient.
Patient
A patient is defined as a person who is in need of care, ill, infirm or disabled, and
occupies this bed.
It is strongly recommended that the operator or user instructs each new patient in
the bed functions that are important for him/her.
Instructions for the Operator:
-This bed fulfils all the requirements of the 93/42/EEC Medical Devices Directive.
It is classified as a Class I active medical device in accordance with the
Medical Devices Act (Medizinproduktegesetz, German abbreviation: MPG)
§ 13.
-Any item of technical equipment, electrical or otherwise, can prove hazardous
if used improperly. Please observe your obligations as the operator in
accordance with the Medical Devices Operator Ordinance (Medizinprodukte-
Betreiberverordnung, German abbreviation: MPBetreibV), in order to ensure
the permanently safe operation of this medical product with no risk of danger
to patients, users or third parties.
Instructions for the User:
-Before using a care bed, the user must check that the bed is fully functional
and in perfect working order, and must observe the instructions in the manual
in accordance with the Operators of Medical Products Ordinance
(MPBetreibV) § 2.
The same applies for accessories that are attached to the bed.

Instruction Manual for Vertica-Homecare Bed
Page 8
2.2 SAFETY INSTRUCTIONS
At the time of leaving the factory, this hospital bed represents state-of-the-art
technology.
Only use the hospital bed if you are absolutely certain that it is in perfect working
order!
The most important objective of the safety information is to prevent personal
injuries. Property damage is also to be avoided.
2.2.1 Explanation of the Safety Symbols Used
In this instruction manual, the following safety symbols are used:
Risk of injury to persons
Dangerous electrical voltage. There is danger to life.
General danger. There is danger to life and health.
Warning of damage to property
Possible damage to the drive unit, materials or the environment.
Other advice
Useful tip. Makes it easier to handle the bed or improves
understanding.
The safety symbols used are not a substitute for the written safety information. It is
important therefore to read the safety information and follow the instructions
exactly!
All persons who work on or with this bed must be familiar with the contents of this
instruction manual and follow all the relevant safety advice.

Instruction Manual for Vertica-Homecare Bed
Page 9
2.2.2 Safety Information for the Operator
In order to ensure the permanently safe operation of this medical product, with
no risk to patients, users or third parties, you must observe your obligations in
accordance with the Medical Devices Operator Ordinance (MPBetreibV)!
Using this instruction manual, which must be provided with the bed, ensure that
every user is instructed in the safe operation of the Vertica-Homecare bed
before using it for the first time!
Draw every user’s attention to the possible hazards that can arise if the bed is
improperly used.This applies in particular to the use of electrical drives and
safety sides!
Only allow this bed to be used by persons who have been instructed in its safe
operation!
Make sure that substitute staff are also sufficiently well instructed in the safe
operation of the bed!
Check to ensure that the safety instructions are adhered to!
Ensure that users know where this instruction manual is kept, in accordance
with the Medical Devices Operator Ordinance (MPBetreibV) § 9!
If the hospital bed is in long-term use, test the functions and check for any
visible damage (see Chapter 6.2) after a reasonable period of time!
If any other equipment is attached to the bed, (e.g. compressors for
positioning systems, etc.), ensure that this is securely fastened and is
functioning properly.
Pay special attention to:
-The safe hook-up of all loose connector cables, tubing, etc.
-Ensure that no multiple socket outlets are located under the bed
-Chapter 2.3.1 Intended Use
-Chapter 4.2.1 Special Safety Information on the Electrical Actuator System
Consult the manufacturer of the equipment in question, or the Burmeier
company, if there are any uncertainties.
2.2.3 Safety Information for the User
Ensure that the operator instructs you in the safe operation of this bed.
Read this instruction manual in order to prevent any injury or damage resulting
from incorrect operation.
Check each time before using the hospital bed to ensure that it is in perfect
working order (see Chapter 3.1)!

Instruction Manual for Vertica-Homecare Bed
Page 10
When adjusting the bed, ensure that no obstacles such as, for example,
bedside lockers, windowsills, supply rails or chairs are in the way in order to
avoid damaging the bed or the obstacles.
If other equipment (e.g. compressors for positioning systems, etc.) is attached,
ensure that all items of equipment are fixed securely and function properly.
Pay particular attention to:
-The safe hook-up of all loose connector cables, tubing, etc.
-Consult the manufacturer of the equipment in question, or the Burmeier
company, if there are any uncertainties.
If any damage or malfunction is suspected, take the bed out of service:
-Unplug the bed from the mains supply immediately.
-Indicate clearly that the bed is “Out of order”.
-Report this immediately to the operator responsible.
Route the mains cable in such a way that it cannot be pulled,
driven over or damaged by moving parts when the bed is
operated. Hazards due to electric shock and malfunctions can be
avoided in this way.
Before moving the bed, always make sure that you have
unplugged it from the mains supply. Hang the mains cable in the
mains cable holder to ensure that it will not fall out or trail on the
floor.
At regular intervals, carry out a visual inspection of the mains
cable to check for mechanical damage (scuffing, exposed wires,
kinks, pressure points, etc.). Such a check should be performed:
-Whenever the cable has been subjected to any mechanical
load, e.g. has been driven over by the bed itself or by an
equipment trolley;
-Whenever the cable has been bent, stretched or violently pulled,
e.g. due to the bed rolling away while it is still plugged into the wall
socket;
-Whenever the bed has been moved or relocated and before
plugging it back into the mains supply;
-Regularly, at least once a week, if the bed is in continuous
operation.
Check the strain relief of the mains cable regularly to ensure that
the screws are tight and secure.
Make sure that the mattress base has travelled to its lowest position
before leaving the patient unattended. In this way, you greatly
reduce the risk of the patient injuring himself/herself as a result of
falling when getting in or out of bed.

Instruction Manual for Vertica-Homecare Bed
Page 11
Always ensure that the castors are braked before leaving the
patient unattended in the bed.
When not in use, always stow the handset in such a way that it
cannot fall onto the floor (hang it on the hook). Make sure that the
cable cannot be damaged by moving parts of the bed.
Do not place multiple socket outlets under the bed. This could
cause electrical hazards due to damaged mains cables or
penetrating fluids.
Before carrying out any adjustments, make sure that there are no
limbs or objects in the way, in order to avoid hazards due to
trapping and/or damage to property. This applies particularly
when mattress base sections are adjusted to a lower height
To safeguard the patient, and children in particular, against
unintentional electrical adjustments, place the handset out of their
reach (e.g. at the foot end of the bed).
In these cases, adjustments must only be performed by, or in the
presence of, a trained person!
Lock the handset if:
-The patient is unable to operate the bed safely or to free
himself/herself from potentially dangerous situations;
-The patient could be at risk from inadvertent adjustment of the
electric drives;
-The patient is exposed to an increased risk of entrapment during
backrest and thigh rest adjustments when the safety sides are
raised;
-Children are left unsupervised in the room with the bed;
Observe the safety information found in chapters:
4.2.1 Special Safety Information on the Electrical Actuator System
4.6.1 Safety Information for Safety Sides
5 Cleaning and Disinfection
6.5.1 Safety Information
8 Special Safety Information for the Use of Accessory Safety Sides
-as well as the safety information found in the various chapters of
this instruction manual!

Instruction Manual for Vertica-Homecare Bed
Page 12
2.3 PRODUCT DESCRIPTION
2.3.1 Intended Use
-This bed is designed for positioning and transporting patients, as an aid to
diagnosing, monitoring, treating, and alleviating illnesses or compensating for
injuries or disabilities.
-This bed is also to bring patients from the supine position to a sitting position
facing forward and then to an upright position in so far as such mobilisation is
prescribed.
-This bed is suitable for accommodating adult patients only (= persons with a
height of at least 146 cm).
-The bed itself is not life sustaining or life supporting.
-The bed has no medical indication.
2.3.2 Use for the Intended Purpose
-This bed is to be used exclusively in senior residences and care homes and
comparable medical facilities with qualified personnel as well as for home
care within a closed area.
-Qualified personnel must be skilled in handling the beds through being
thoroughly conversant with the instruction manual.
-If the bed changes owners, the instruction manual must be handed over with
the bed.
-The use of this bed in hospitals is only permitted in rooms designed for medical
treatment of the application group 0 (in accordance with VDE 0100 part 710
to VDE 0107). This care bed was not designed for any other usage!
-This bed can be used for care under the supervision of a physician and be
used for diagnosis, treatment or observation of the resident. Therefore it is
equipped with the option to lock the handset.
-The bed with its stable, smooth-running castors is designed for being moved
within the room as well as frequently in corridors and across thresholds with a
height of up to 2cm.
-This bed has no special connectors for potential equalisation. Please pay
attention to this before connecting additional (medical) electrical equipment.
If necessary, further advice on additional protective measures can be found:
-In the instruction manuals of these additional electrical devices (e.g.
compressed air positioning systems, infusion pumps, enteric feeding
devices ...)
-In the DIN EN 60601-1-1:2002 standard (Safety of Medical Electrical
Equipment)
-In the standards VDE 0100 part 710 (formerly VDE 0107) (High voltage
systems in hospitals).

Instruction Manual for Vertica-Homecare Bed
Page 13
-This bed may be operated without restrictions and with a permanent
maximum load of 225 kg (= safe operating load, consisting of
occupant and accessories) Symbol:
-The permitted weight of the patient depends on the total weight of
the accessories attached at the same time (e.g. respirators,
infusions,…) Symbol:
-The information applicable for your bed is given on a sticker with the
above symbol which is located on the chassis of the bed.
-Example:
Weight of accessories
(incl. mattress)
Max. permitted
weight of patient
15 kg
210 kg
40 kg
185 kg
-This bed is designed for re-use. When re-using the bed, observe the following
requirements:
-Cleaning and Disinfection (see Chapter 5)
-Maintenance / Repeat Inspections (see Chapter 6).
-This bed may not be used in explosive environments caused, for example, by
cleaning agents or anaesthetics.
-This bed may not be used in combination with high frequency surgical
equipment.
-Before using the safety sides, assess and take into consideration the clinical
condition and particular physical build of the patient:
-For example, if the patient is extremely confused or very restless, avoid
using safety sides as much as possible and make use of alternative
safety measures such as posey belts, restraint sheets, etc.
-In the case of particularly small, slightly built patients it may be
necessary to use an additional form of protection to reduce the size of
the safety side gaps. In these cases, use protective covers (accessory),
posey belts, etc.
2.3.3 Contraindications
This bed is only suitable for patients who do not fall
below the following minimum body
measurements/weight:
oHeight: 146 cm,
oWeight: 40 kg
oBody Mass Index1“BMI“: 17.
Owing to the smaller limbs of occupants with a body size/weight that is less
than this, there is an increased risk of entrapment between the open spaces of
the safety sides when safety side systems are used.
1 Calculation of BMI = 󰇟󰇠
󰇟󰇠; example: a) 
  OK!; b)    Not ok
Sticker on
bed chassis

Instruction Manual for Vertica-Homecare Bed
Page 14
2.3.4 Side Effects
Take suitable measures to prevent decubitus in long-stay patients.
The Vertica-Homecare bed may only be used under the operating conditions
described in this instruction manual.
Its use for any other type of application is deemed to be contrary to the intended
purpose!
2.3.5 Special Features
-Integrated automatic upright stand-up function is easy on patient and staff
-Integrated, large linen holder
-Bed extension, at the foot end
-Reverse-Trendelenburg position up to about 16°
-Castors (12.5 cm; with central locking; steering lock for moving in a straight
line)
-Mattress base in four sections, mattress base dimensions 200 x 90 cm; external
dimensions approx. 104 x 214 cm
-Mattress base height adjustment range from approx. 40.5 to 81 cm via two
lifting columns
-Adjustment of backrest from 0° to approx. 70° (up to approx. 85° for upright
position)
-Adjustment of the thigh rest from 0° to approx. 30°
-Extended leg position from 0° to about 15°
2.3.6 Materials Used
The bed is made predominantly of steel sections. Their surface has a polyester
powder coating or a metallic coating made of zinc or chrome.
The mattress base is made of high-quality, PVC-free plastics.
Side panels and side rail bars are made of aluminium profile with wood finish foil.
The chassis is made of steel sections / cast metal parts.
The headboards and footboards consist of wood or wood-based material with
sealed surfaces.
All surfaces are recognised as being safe for contact with skin.

Instruction Manual for Vertica-Homecare Bed
Page 15
2.3.7 Structural Design
Mattress base
The mattress base is divided into a backrest, a seat section, a thigh rest and a
lower leg rest. The mattress base height can be adjusted horizontally, and can be
tilted into a Trendelenburg or reverse-Trendelenburg position.
When activated by the medical personnel, the mattress base can be returned to
an upright or sitting position.
All adjusting functions are electrically powered. The components for the electric
drive system are mounted in the mattress base.
Chassis
Under the mattress base is the chassis for the columns which can be adjusted
electrically for height and incline. The bed has four castors that can be centrally
locked. One of the castors is equipped with a steering lock which enables the
bed to be moved in a straight line.
Safety sides
The bed is equipped with an integrated "Multiflex" safety side system to protect
the occupant from accidentally falling out of bed.
Electric drive system
The electric drive system for this bed consists of:
-A central control unit, installed underneath the mattress base, with a
transformer that generates a 24 volt protective low voltage, which is harmless
for patients and users. The drives, the handset, and the control panel are
connected to the control unit. These components operate on the 24 volt
protective low voltage generated and have dust and water protected plug
connections.
-Rechargeable batteries for emergency operation, independent of the mains
supply.
-One handset for patient to adjust the bed; integrated option for the care staff
to individually lock electrical adjustment functions
-One handset for the stand-up function, separately activated and operated by
the care staff
-One drive for the backrest.
-One drive for the thigh rest
-One drive for the lower leg rest
-Two drives for the lifting columns for mattress base height and pivoting.
-Brake alert
-Under bed light (optional)

Instruction Manual for Vertica-Homecare Bed
Page 16
3Initial service
No electrical measurements are necessary prior to putting this bed into service for
the first time, since the bed was tested by the manufacturer for electrical safety
and functionality and left our factory in perfect condition.
Before putting the bed into service for the first time:
Remove all transport securing devices and packaging film.
Clean and disinfect the hospital bed (see Chapter 5).
Use only authorised accessories (e.g. mattresses, external safety sides), to
minimize endangering patients through becoming trapped or falling out of
bed. For more details, see Chapter 4.6.1 and Chapter 8.
Remove the locking key at the handset cable (release
transport securing device) and put the locking key out of the
range of patients or other parties (such as key ring users /
carers; see also chapter. 4.2.2).
Each time before putting the bed into service, the user must check that:
-The bed has been cleaned and disinfected;
-The castor brakes are applied (see Chapter 4.1);
-No obstacles such as bedside lockers, supply rails or chairs will impede bed
adjustments;
-All adjustment facilities work properly and have been checked (see Chapter
3.1).
Additionally for electrical beds only:
-the power supply is compatible with the bed (230 Volt AC, 50/60 Hz);
-the mains cable is connected and routed in such a way that it cannot be
damaged;
-the mains cable, drive cables and handset cable cannot be damaged by
moving parts of the bed;
-if the bed is equipped with rechargeable batteries, it is always connected to
the mains supply. - Otherwise the batteries will not charge and be
unavailable for use in an emergency.
The bed may be put into operation only after carrying out these checks!

Instruction Manual for Vertica-Homecare Bed
Page 17
3.1 CHECKLIST:INSPECTION BY THE USER
Inspection
What to Check… Check for…
Ok
Not
Ok
Description of
Defect
Visual Inspection of the Electrical Components (if installed)
Handset
No cracks in housing or
keypad
Handset cable,
mains cable
No external damage,
cables laid without
danger of being
trapped
Visual Inspection of the Mechanical Components
Grab handle with strap
No damage
Mattress base, covers
No damage, (cracks,
deformation)
Performance Check of the Electrical Components (if installed)
Patient handset;
Stand-up handset
Press all buttons, one
after the other (for
approx. 1 second).
Function according to
the printed
details/instruction
manual
Performance Check of the Mechanical Components (if installed)
Castors
Brakes are effective
Side rails,
safety sides
Engages securely
when raised
Accessories (e. g.
patient lifting pole, grab
handle with strap)
Secure fixings, suitable
Inspector’s signature:
Inspection results:
Date:

Instruction Manual for Vertica-Homecare Bed
Page 18
3.2 LOCATION REQUIREMENTS
There must be sufficient room available to accommodate the bed's entire
range of adjustments. Obstacles such as bedside lockers, supply rails, furniture,
or window sills must not impede adjustments.
Before using the bed on parquet flooring, check whether the castors can
leave marks on the parquet varnish. We accept no liability for such wear. The
stretcher can be used on tiles, carpet, linoleum or laminate flooring without
causing any damage.
A properly installed 230 volt, earthed mains socket must be available close to
the bed, at the head end (if possible).
If other equipment (e.g. compressors for positioning systems, etc.) is attached,
ensure that all items of equipment are fixed securely and function properly.
Pay special attention here to the safe routing of all loose connector cables,
tubing, etc. If you have any queries or concerns, consult the manufacturer of
the equipment or the Burmeier company.
Minimise, as far as possible, the risk of fire due to external influences.
Instruct users on these points:
Use only flame-retardant mattresses and bedding if possible.
Avoid smoking in bed, since the mattress and bedding used may
not be resistant to smokers' accessories.
Only use additional equipment (e.g. electric blankets) and other
electrical devices (e.g. lamps, radios) that are in perfect working
order!
-Ensure that this equipment is used only for the purpose intended.
-Ensure that this equipment is not unintentionally placed on or
under the bedding (danger of overheating)!
Avoid using extension cables or multiple socket bars under the bed
(risk of fire due to penetrating fluids).
Extension cables and/or multiple socket outlets should not be used
at all.

Instruction Manual for Vertica-Homecare Bed
Page 19
4Operation
4.1 MOVING AND BRAKING THE BED
The bed is equipped with four lockable castors and central locking at the foot
end. A steering lock can be activated for one castor at the foot end of the bed,
which makes it easier to move the bed in a straight line and to manoeuvre the
bed.
The bed may be moved within the room even while the patient is in it
when it is in the lowest position.
As a general rule, always apply the brakes when the bed is not
being moved or when a patient is left unattended in the bed.
Each time before moving the bed, ensure that:
-The mains cable cannot be stretched, driven over or damaged in
any other way.
-The mains cable has been hung in the mains cable holder (see
Chapter 4.5.3).
-The mains cable does not trail on the floor.
-The cables, tubes or wires of any mounted equipment are
adequately secured and cannot be damaged.
Otherwise, the mains cable could sustain damage as a result of
being torn off, crushed or driven over. Such damage could lead to
electrical hazards and malfunctions.
When the stretcher is moved, ensure that objects hanging in the
universal holder [11] do not cause any damage (e.g. to door
frames).
Risk of crushing! When transporting a patient, ensure that the
patient’s hands and feet do not protrude over the edge of the
bed and that they cannot get in the way of the wall deflection
rollers.
Brake Alarm Function: If the mains cable is plugged in and
the castors are not braked, a warning signal sounds (for
max. 5 minutes). This is to alert someone to brake the bed
or unplug the mains cable.
Braking
Press down on a foot lever [14].
Check to ensure that the bed is
properly braked.
Moving without the steering lock
Foot lever [14] in horizontal middle position
Moving with the steering lock
Raise a foot lever [14] with
the back of the foot.
If you push the bed from the foot
end now, it will be easier to steer.
Braking
Headboard
Moving with
the steering
lock
Direction of travel
Moving without
the steering
lock

Instruction Manual for Vertica-Homecare Bed
Page 20
4.2 ELECTRIC DRIVE SYSTEM
4.2.1 Special Safety Information on the Electrical Actuator System
This hospital bed may not be used in combination with high-
frequency surgical equipment or in explosive environments!
When using accessories:
Make sure that the attachment of accessories does not produce
any crush or shearing zones when the bed sections are adjusted. If
this cannot be ensured, the user must lock the handset using the
control panel or the locking box!
When making any adjustments, always ensure that there are no
limbs belonging to patients, users, other persons, and especially
playing children, that could be trapped underneath the rests or
the mattress base.
Ensure that the mains cable and handset cable cannot be driven
over or otherwise crushed when the bed is moved.
Always keep the handset in a safe place, where the housing and
buttons cannot be damaged mechanically, particularly as a
result of collision with other objects. Hang the handset on the hook
or holder provided, within the protected bed area. This helps to
protect patients from hazards arising from functional defects and
unintentional movements.
Ensure that no obstacles, such as bedside lockers, supply rails, wall
protection rails, window sills etc. or chairs could impede
adjustments to the bed.
Ensure that there are no objects on the chassis.
Otherwise, mechanical damages could occur to the bed and/or
related objects which could impede safety.
When routing the handset cable, ensure that it cannot be
damaged by any moving parts of the bed.
Ensure that the mains cable and handset cable cannot be driven
over or otherwise crushed when the bed is moved.
Continuous operation must not exceed two minutes! After this
time, a rest period of at least 18 minutes must be observed.
Alternatively: one minute continuous operation followed by a nine
minute rest period.
If the electric drive is operated for a much longer period, e.g. due
to the patient "playing" continually with the handset, the thermal
protection device integrated in the transformer of the control unit
will deactivate the drive permanently. In this extremely rare case,
the control unit must be replaced.

Instruction Manual for Vertica-Homecare Bed
Page 21
Electrical adjustments are only possible when the bed is properly
connected to the mains supply (exception: emergency operation
using rechargeable batteries).
If the load is too high, an electronic overload switch is activated
and the control unit is automatically switched off. When the
overload is removed, the actuator system resumes operation.
As electro medical equipment, this bed is subject to special safety
procedures with respect to electromagnetic compatibility (EMC).
For this reason, observe the following instructions when installing
and operating the bed:
oPortable and mobile high-frequency communication devices
(e.g. cordless telephones, mobile telephones, baby monitors,
WLAN, WIFI, wireless equipment, etc.) can influence the
operation of electro medical equipment. These influences have
been minimised by means of the robust, interference-resistant
design of the electrical adjustment features of this bed.
oAs with every electrical device, even if all the specified EMC
limiting values are observed during operation, disruptions from
and to other closely situated high-frequency communication
devices cannot be completely ruled out (e.g. “crackling” in a
radio). In such rare cases, increase the distance between the
devices or align them differently, and make sure that they do not
use the same electrical outlet, or switch the disruptive/disrupted
device off temporarily.