BWI Eagle AIR-EAGLE XLT Manual

PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®XLT
900 MHz RF Transmitter
MODEL 441P-12-ESTOP-120VAC
DESCRIPTION
The AIR-EAGLE XLT, MODEL 441P-12-ESTOP-120VAC is an R.F.
transmitter designed to work with the model 441P-8-ESTOP receiver
for failsafe emergency stop of any electrical apparatus. This transmitter
has been factory programmed to emit a beacon signal that keeps the
relays in the remote receiver energized. This provides a “handshake
link” between the two units that if lost will automatically de-energize the
E-Stop relay and shut down the equipment. While linked, pressing the
E-Stop button will immediately de-energize the E-Stop relay. This
transmitter is capable of reaching the receiver from up to 2500 feet (or
more w/external high gain antennas) away and has seven user-
selectable network frequencies to allow multiple systems to operate
simultaneously in the same area without interference.
INSTALLATION
1. Mount the AIR-EAGLE XLT TRANSMITTER in a convenient location
where the operator will have easy access to the stop button.
2. Install antenna onto antennaconnector located onthe right side on
the enclosure.
3. Plug supplied AC to DC wall plug adapter into AC outlet.
TERMINAL STRIP WIRING
Wire as shown based on number of contact inputs
1
2
3
4
5
6
7
8
9
10
E-Stop Button Pre- Wired to Input 1
C Input 2
Input 2
C Input 3
Input 3
C Input 4
Input 4
(-) 12VDC input from included AC wall adapter
(+) 12VDC input from included AC wall adapter
Dimensions (with mounting plate) 6.3” L x 4.8” W x 4.3” H
CONTROLS & INDICATORS
PWR/TX LED
Illuminates green continuously while power
is applied. Changes to red when transmitting
data.
Beacon Emission
Invisibleto the user this unit transmits a
beacon signal every .1 seconds to keep the
remote relays energized
STOP Pushbutton
Transmits CH1 RF “STOP” code to receiver
FREQUENCY SET-UP
This transmitter is factory set to Frequency #1. This setting can be
changed by the user at any time by following the directions below:
1) Remove power from unit
2) Remove top cover.
3) Select desired network frequency using table below.
4) Reattach cover and apply power.
5) Programming is now complete.
SEL 2 (SW 1-3):
(NETWORK
FREQUENCY)
Network
Frequency
SW1
SW2
SW3
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
SEL2 (SW4)
Reserved for future use

AIR-EAGLE®XLT
900 MHz RF Transmitter
MODEL 441P-12-ESTOP-120VAC
APPROVALS
United States (FCC)
MCQ-XB900HP
Canada (IC)
1846A-XB900HP
SPECIFICATIONS
AC Input
100-240 VAC, 16 W, 50/60 Hz from
supplied wall adapter
Transmit Data Channels
Four Dry Contact Input
RF Output Power
250 mW
Transmit Range
Approximately 2500 Feet w/standard
antenna
Transmit Frequency
900MHz Spread Spectrum
Frequency Channels
7 Independent Network Frequencies
Enclosure
Polycarbonate, IP66 (NEMA 4)
Antenna Connection
TNC Female
Operating Temperature
-40oF to +185oF
REPLACEMENT PARTS & ACCESSORIES
PC Board (Main)
441P-12-ESTOP2-120VAC
Standard Antenna (Included):
900MHz TNC Portable Antenna
(For distances up to 2500 feet*)
49-1101
Optional Antennas and Accessories –
Used to increase range in both non line of sight and line of sight
applications. - Contact BWI Eagle for recommendations
900MHz Thru-Hole Mount
Mobile Antenna
49-2101
900MHz Magnetic Mount Mobile
Antenna
49-2102
900MHz Omni Directional
Antenna
49-3101
900MHz 13dB Yagi Antenna
49-3102
Flex Coax Cable w/Connectors
–Connects external antenna(s)
to base unit(s).
49-4000-XX (XX = # of Feet)
* = Line of Sight
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants theAir-Eagle Remote Control System, if properly
used and installed, will be free from defects inmaterial and workmanship
for a period of 1 year after date of purchase. Said warranty to includethe
repair or replacement of defective equipment. This warranty does not
cover damage due to external causes, including accident, problems with
electrical power, usage not in accordance with product instructions,
misuse, neglect, alteration, repair,improperinstallation, or improper
testing. This limited warranty, and any impliedwarranties that may exist
under state law, apply only to the original purchaser of the equipment, and
last only for as long as such purchaser continues to own the equipment.
This warranty replaces all other warranties, express or implied including,
but not limited to, the implied warranties or merchantability and fitness for
a particular purpose. BWI Eaglemakes noexpress warranties beyond
thosestated here. BWI disclaims without limitation, implied warranties of
merchantability and fitness for a particular purpose. Some jurisdictions do
not allowthe exclusion of implied warranties so this limitation may not
apply to you. To obtain warranty service, contact BWI Eagle for a return
material authorization. When returning equipment to BWI Eagle, the
customer assumes the risk of damage or loss duringshipping and is
responsible for the shipping costs incurred.
DOCUMENT DATE: 03/01/2019 / PRODUCT REV. 4
105 Bonnie Drive
Butler, PA 16002
[phone]
Fax [phone]
www.bwieagle.com