C.A. Technologies Jaguar 100 Series User manual


  



 



  


 !""#$"


   
   
   
   
   
   
   
 
 
 
  !"#"$%&'()"$

  



 



  


 !""#$"
  
  
*  
   
   
   
   
   
   
    
    
  
  
  
  
+"%"+,$--"$,#$$,$,#."$"$/$) 
+,% ""$
0+)1#2$
%&''
%&''

3 
 
4$"+,,



Jaguar 100 Series
GRAVITY FEED SPRAY GUN
PRODUCT INFORMATION
Coating Atomization Technologies P.O. Box 17820, Boulder CO 80 08 [phone] Fax ( 0 ) 4 8-5708
www.sprayCAT.com

Operation and Maintenance Instructions for Jaguar Gravity Spray Guns
Operation
1. Connect air supp y hose at hand e of gun. 5/16 air hose x 25 ft. max. ength is recommended. A so,
on y use CAT high f ow quick disconnects and avoid using any restrictive fittings for the air supp y to
the gun.
2. Screw the paint cup onto the guns gravity feed f uid in et.
3. F uid f ow can be contro ed using the f uid contro knob, this restricts f ow by imiting need e trave . It
is best to contro f uid f ow by the proper se ection of orifice size and use the f uid contro knob to
fine tune f ow rate.
4. Fan width can be adjusted using the fan contro knob. Turning the knob c ockwise narrows the fan.
Maintenance
IMPORTANT! Routine c eaning and maintenance is essentia to insure proper gun operation.
Severa states prohibit spraying so vent into the atmosphere and require the use of covered gun c eaner.
1. If a gun c eaner is being used, connect and c ean the gun in the gun c eaner according to the
manufactures instructions.
2. If a gun c eaner is not being used:
Remove air cap and c ean separate y using c ean so vent.
C ean the gravity feed cup thorough y, then spray c ean so vent through the gun unti c ean.
NOTE: Gun disassembly is not recommended for normal cleaning and maintenance.
Gun disassembly and reassembly instructions:
Have repair kit # 10-105 avai ab e before gun disassemb y.
Disassembly
To remove nozz e carrier (5) and air cap adapter (7):
1. Remove the air cap (1), f uid tip (2), f uid nozz e body (3) and need e (16).
2. Remove need e sea cartridge (17).
3. Loosen ocknut (11) and remove f uid in et (12).
4. The f uid nozz e carrier (5) and air cap adapter (7) wi now s ide foward from the gun hand e (13).
Reassembly
1. Insta new o-ring (8) on the air cap adapter (7).
2. Insta air cap adapter (7) into gun body (13).
3. (For Lynx 100 Conventiona On y) insta sea (4) onto air cap adapter (7).
4. Insta the ocknut (11) and sea (10) onto the f uid in et (12) as far as possib e.
5. Insta a new f uid in et sea (9) into the recessed area on the nozz e carrier (5) in et port.
6. Insta carrier sea (6) onto the back of the nozz e carrier (5).
7. S ide the nozz e carrier (5) into the air cap adapter (7) as far as possib e. Be sure the nozz e carrier
extends into the ho e at the back of the gun head. Insta the need e sea cartridge (17) but do not tighten.
8. Rotate the nozz e carrier (5) unti the f uid in et port in the nozz e carrier is a igned with the threaded ho e
in the gun body (13). Whi e in this position, insert the f uid in et (12) and tighten firm y.
9. Tighten need e sea (17) to approx.12 ft- bs torque.
10. Tighten f uid in et (12) to approx. 25 ft- bs torque.
11. Tighten ocknut (11) to approx. 33 ft- bs torque.

IT EM NO. PART NO. DESCRIPTION IT EM NO. PART NO. DESCRIPTION
1 See Air Cap Chart Air Cap* 17 60-1400 Needle Seal Cartridge**
2 See Air Cap Chart Fluid Tip* 18 60-1033 Trigger Pivot Screw s
31-1201 (HVLP) Fluid Nozzle Body (for HVLP) 19 60-2101 Trigger
31-2201 (CONV) Fluid Nozzle Body (for Conv) 20 60-1520 Air Valve Assembly
4 61-1005 (CONV) Seal** (CONV) 21 60-302 Air Valve Poppet
60-J11H (HVLP) Nozzle Carrier (HVLP) 22 60-125 Seal**
60-J11C (CONV) Nozzle Carrier (HVLP) 23 61-1003 Air Valve Spring**
6 60-123 Carrier Seal 24 60-119 Seal**
60-12H (HVLP) Air Cap Adapter (HVLP) 25 60-201 Rear Bushing
60-12C (CONV) Air Cap Adapter (CONV) 26 60-204 Needle Return Spring**
8 60-131 O-Ring** 27 60-205 Spring Seat**
9 60-124 Fluid Inlet Seal** 28 60-202 Fluid Control Knob
10 60-130 Seal** 29 60-1510 Inlet Air Control (Optional)
11 60-118 Locknut 30 60-122 Plug
12 60-127 Fluid Inlet 31 60-104 Air Inlet Fitting
60-1113 Jaguar Gun body (HVLP) 51-401 standard 750cc Gravity Feed Cup (aluminum)
60-1123 Jaguar Gun body (CONV) 51-400 optional 750cc Gravity Feed Cup (plastic)
14 98-0109 Allen Plug 51-403 optional 1 liter Gravity Feed Cup (aluminum)
15 See Air Cap Chart Fan Control Assembly 33 51-418 Gravity Cup Lid
16 See A ir Cap Chart Fluid Needle*
*See air cap selection chart on pages 1 & 4
**Indicates part included in repari kit # 10-105
3
5
7
13 32
FOR
J100H GUNS
HV LP A IR CA P TEST GA UGES
21-1090-G
21-1092-G
21-1093-G
21-1095-G
21-1097-G
21-1195-G
21-1197-G

MATERIAL TYPE Orifice
Size Air Cap HVLP Air Cap CONVENTIONAL
21-1095 50 psi @ 22.5 cfm
Sealer
Single Stage
21-1195 50 psi @ 22.5 cfm
21-1093 18 psi @ 10 cfm
Basecoat
Clearcoat
High Solids Clears
1.7
1.4-1.7
1.3-1.4
1.3-1.4
1.3-1.4
Filler
Primer/ Washprimer/Epoxy
21-1093 18 psi @ 10 cfm
1.4-1.7 21-1094 33 psi @ 13 cfm
21-1093 18 psi @ 10 cfm
1.3-1.5 21-1093 18 psi @ 10 cfm
21-2466 50 psi @ 15 cfm
21-2466 50 psi @ 15 cfm
21-2466 50 psi @ 15 cfm
FLUID NOZZLE / AIR CAP SELECTION CHARTS
Jaguar 100 Series - Gravity Feed Spray Guns
21-2466 50 psi @ 15 cfm
21-2466 50 psi @ 15 cfm
21-2466 50 psi @ 15 cfm
21-2466 50 psi @ 15 cfm
Revised 12/6/11