CABINETS TO GO Findley & Myers LCD2484 User manual

Page 1
Pantry Cabinet with 3 Drawers
ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all Pantry Cabinets with 3 Drawers.
ITEM #LCD2484, LCD2490, LCD2496

Page 2
►General Instructions:
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned tofacethe
testofdailyuseandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityfor
anydamagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,
significantdamageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.
CabinetsToGowillnotbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE
PARTS IN THE QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER
CARE IMMEDIATELY AT 1-800-CABINET.
►ItemsQuantity
►Required tools:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
►Hardware Box:
a
b
Qty 16 Qty 13
c
d
Qty 6 Qty 6 - 3 Sets
A
A
B
Hx3
F
B
D
G
A
G
G
C
C
C
Item Description Qty
A Face Frame with Door 1
B Side Panels 2
C Top, Center, & Bottom Panels3
D Back Panel 1
E Shelf 3
F Toe Kick 1
G Drawer Front 3
H Drawer Box 3
I Hardware Box:1
Bumper 20pcs, shelf clips 12pcs, drawer slide 3-sets , drawer rail holder 6pcs, 1" Round Head Screws 13pcs
e
Qty 12
Ex3
The materials listing above are for the largest unit in this instruction set. Smaller units may require less
hardware and materials; therefore, your item may contain a smaller number of each.

Page 3
IftheLCDyouareinstallingrunsthelengthofyourceilingheight,itis
recommendedtoassembletheunitstandingtoavoidscrapingyourceiling.
►Instructions:
2.
Installing the Side Panels: Insert the right and left side panels (B) into the grooves of the back panel
(D)andalign the camlockconnectors.(Figure2) Lockthe camlock witha screwdriverbyturning the screw 180°
clockwise. (Figure 3)
3. Installing the Toe Kick (F): Place the toe kick (F) at the end of side panels (B). Aligneachcamlockonthe
toekickandlockthem. (Figure 4)
4.
Install the Top, Center, & Bottom Panels (C)bysliding them in to the grooves.
5.
Install the face frame (A)byplacingcamlocksidedownontotheboxofthecabinet.(Figure 6) Align all
grooves and cam locks onto the face frame and coordinating cam locks. It may be necessary to open all
cabinet doors. Lock all face frame cam locks with a screwdriver. (Figure 3)
A
Figure6
Figure 2
D
B
Figure 4
Figure 3
F
C
B
Figure 5
B
C
C
Figure 1
1.
Put the Back Panel (D) face up on a flat soft working surface to ensure that the surface is not scratched
or damaged. Attach the drawer rail holders (c) to the pre-spotted areas using the supplied screws. (Figure 1)
c
Qty 6
Top
c
NOTICE

Page 4
1. Place the face frame (A) face downona flatsoftworking surfacetoensure thatthe
faceis not scratched or damaged. (Figure 1) .
2. InstalltheSidePanels(Figure2): Insertrightandleftsidepanels (B) intothegrooves of
thefaceframe (A) andalignthecamlock connectors (Figure2). Lockthe camwithascrewdriver
byturningthescrew180° clockwise (Figure4) .
3. InstalltheBottom and Microwave shelf(Figure3): Gently spreadtheside panels (B)and
insert (C) & (D) intothegroovesofsidepanels (B) untilthey areseated in theface frame (A).
4. Installing theBack PanelandToeKick (Figure5): Beforeyoustartthisstep,putthe
backpanel (E) onaflatsurfacefacingupward.Installthedrawer slide supports (f) inthepre‐
spottedareaonthebackpanel (Figure6). Thebottom of the slide supports should be facing
the bottom groove.Securethemwith2screws each (e)( Figure6).
Theninstallthe backpanel (E)
to the rearofsidepanels (B)(Figure5) .Alignandlockeachcamlock.InstalltheToeKick (F) by
lockin
► Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Ne
ver use abrasive cleaners containing acetone, chlorine or strong ble ach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the quality and lo ok of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.
G
H
6. Drawer Assembly (Figure 7): First assemble the drawer front (G) with drawer box front
(H) with screws (b).Then assemble the rest of the parts of the drawer box (H) using your
palm, or a rubber mallet if needed, to secure the dove tails into position. Repeat step for
additional drawers.
b
Qty 13
8. Install the rubber buttons (a) onto the corner of the doors where they come in contact
with the frame. Insert adjustable shelves (E) into the fully assembled cabinet using shelf clips (e).
a
Qty 16
7. Install the drawer slides (d) into the assembled cabinet onto the drawer rail holders (c)
installed in Step 1, using the pre-drilled holes in the frame, and the provided screws. (Figure 8)
d
Qty 6 - 3 Sets
Top
dc
Figure 7
Figure 8
e
Qty 12