CABINETS TO GO Findley & Myers BC09 User manual

ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all Base Cabinets
ITEM# BC09, BC12FH, BC15FH, BC18FH
Page 1

►Items Quantity
Item Description Qty
A
Left Side Panel 1
B
Right Side Panel 1
C Back Panel
1
D Bottom Panel
1
E Frame & Door 1
F Shelf 1
G
Hardware Box
1
Bumper 2pcs, Shelf Bracket 4pcs, 1/2" Round Head Screws 8pcs, Plastic Corner Brackets 4pcs
► Required tools:
Page 2
►General Instructions:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
► Hardware Box:
a
bc
Qty 4 Qty 8Qty 2
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
Toe Kick
d
Q ty 4
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.

1
2
A
B
D
E
Figure 2
Page 3
Figure 1
SoftSurface
Hard Surface
E
E
Assemble the Side Panels (A,B) onto the
Frame (E) by connecting the male and
female cam locks and using a screwdriver
to turn the lock clockwise. (Figure 1)
{NOTE: Lay Frame and Door on a flat smooth soft
work surface to assemble.}
Insert the Bottom Panel (D)
into the groove of the Side
Panels and Frame.
(Figure 2)

C
3
4
G
Figure 4
Page 4
Figure 3
Install the toe kick (G) onto
the side panels (A,B) and
lock the cam locks.
(Figure 3)
Install the Back Panel (C)
onto the side panels (A,B)
and lock the cam locks.
(Figure 4)

d X4
6
b X8
5
X4
F
a
a
Figure 6
Page 5
Figure 5
Insert the shelf brackets (a)
into the side panels (A,B)
in the location of your
choosing. Then insert
Shelf (F) onto the brackets.
(Figure 5)
Install the corner brackets (d)
in the four top corners using
screws (b).
(Figure 6)

►Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use abrasive cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets
etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by
email - [email protected] or call 1-800-CABINET.
c X2
c
7 Install the bumpers (c) onto the
corner of the door where it comes
in contact with the frame as
shown.
(Figure 7)
Figure 7
Page 6