CABINETS TO GO Findley & Myers AB124 User manual

Angle Base Cabinet
ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all Angle Base Cabinets
ITEM #AB124
Page 1

►Items Quantity
Item Description Qty
A
Face Frame and Door 2
B
Side Panel 1
C
Bottom Panel
1
D Back Panel
1
E Shelf 1
F
Toe Kicks
2
G
Hardware Box
1
Bumper 4pcs, Plastic corner bracket 1pcs, "L" brackets 2pcs , Wood corner brackets 3pcs, 1/2" Flat Head Screws 4pcs, 1/2" Round Head Screws 2pcs,
► Required tools:
Page 2
►General Instructions:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
► Hardware Box:
a b e
Qty 14
f
Qty 4
cd
Qty 4 Q ty 1 Qty 4Qty 2
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
g
Qty 2
h
Qty 3
1" Flat Head Coarse Thread Screws 14pcs, 1" Flat Head Screws 4pcs
1/16"
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.

C
E
4. Assembling the Face Frames: Remove Door. Place one face frame (A) on a flat surface and install wood blocks (h) with screws (e) being careful of the placement.
(Note:There are no pre-drilled pilot holes in the frames. You can use a 1/16" drill bit, drilling 1/4" deep, if needed.)
5. Align the Frames with the side and back panel.(Figure 6&7) Align the cam locks and lock them by turning the screw to the right 180° (Figure 3)
Attach frames to bottom panel using screws (f) insuring frame is flush with the bottom panel, and aligned with each other.
B A
Page 3
B
D
Figure 3
3. Insert the bottom panel (C) and shelf (E) (Figure 4), well align the cam locks and lock the connectors with a
screwdriver by turning the screw located on the cam lock connector to the right 180° (Figure 3).
►Instructions:
1. Place Back Panel (D) face down on a flat soft working surface (Figure 1) .
2. Insert side panel (B) into the grooves of back panel (D) .(Figure 2) Align
the plastic half part of the cam lock connectors. Make sure it fits and lock connectors with a
screwdriver by turning the screw located on the cam lock connector to the right 180° (Figure 3)
A B
A B
Figure 1
Figure 2
Figure 4
Figure 5
Figure 6
Figure 7
Figure 9
Figure 10
Figure 11
Figure 12
b
g
A
B
SoftSurface
Hard Surface
D
D
A
F
F
F
F
F
Top View
a
b
Qty 4
Q ty 1
e
Qty 6
f
Qty 4
h
Qty 2
d
Qty 2
6. Connect both Toe Kicks (F) together with “L” brackets (g) with screws (c)(Figure 10A). Align the toe kicks with the cam locks at the bottom of the side and back panel.
(Figure 9) Install the Toe Kicks (F) by locking the cam locks at both ends. (Figure 10B) Install the plastic corner bracket (b) with screws (d) (Figure 11&12).
Install bumpers (a) on inside of doors.
c
Qty 4
g
Qty 2
d
c
1/16"
Optional
f f
e
h
Figure 8
(Figure 8) Finish attaching the frames to each other with the wooden blocks (h) that were attached in Step 4.
Install the remaining wooden block (h) with screws (e) as a shelf support onto the frames. (Figure 11)
h
Qty 1Qty 4
e

Page 4
► Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use abrasive cleaners containi ng acetone, chlorine or strong bleach. Al
so, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cle aner on chrome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the qual ity and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.