CABINETS TO GO Findley & Myers BC12 User manual

Page 1
BaseCabinet 
ASSEMBLY INSTRUCTIONS
Theseassemblyinstructionsare onlyapplicableforallone drawer BaseCabinets.
ITEM#BC12,BC15,BC18,BC21,BC24,BC27,BC30,BC33

Page 2
►Items Quantity
Item Description Qty
AFaceFramewithDoor 1 (2)
BSidePanels 2
CBottomPanel 1
DBackPanel 1
EShelf 1
FToeKick 1
GDrawerFront 1
HDrawerBox: Front 1pc, Back 1pc, Sides 2pcs, Bottom 1pc 1
IHardwareBox: 1
Bumpers8pcs,Plasticcornerbracket4pcs,1/2"roundheadscrews8pcs,Shelfclips4pcs,1/2"flatheadscrewsforslide12pcs
1"screw3-5pcs, Slide Rails 2 Sets, Slide Rail Supports 2pcs
►General Instructions:
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT
1-800-CABINET.
►Required tools:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
►Hardware Box:
a b ge
Qty 12
f
Qty 3-5
cd
h
Qty 2Qty 2 - 1 Set Qty 8 Q ty 4 Qty 8 Qty 4
H
A
G
H
A
F
B
D
B
C
E
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.

Page 3
►Instructions:
1. Placethefaceframe (A) facedownon aflatsoftworkingsurfacetoensurethatthefaceis 
not scratchedordamaged (Figure1) .
2. InstallingtheSidePanels(Figure2): Insertrightandleftsidepanels (B) intothegrooves of
the face frame (A) and align the cam lock connectors (Figure 2). Lock the cam
wit hascrew driver byturningthe screw180°clockwise (Figure4) .
3. InstallingtheBottom(Figure3): Gentlyspreadthesidepanelsandinsertthebottom (C)
intothegroovesofsidepanels (B) untilitis seated inthefaceframe
 (A). Alignitandlockeachcam.
4. InstallingtheBackPanelandToeKick(Figure5): Before youstartthis step,placethe
bac kpanel (D) onaflatsurfacefacingupward.Installthedrawerrailholders (g) inthepre‐ 
spotted area on the back panel (Figure 6). Securethemwith2flatheadscrews (e) ( Figure6). Then
put thebackpanel (D) atrear of side panels (B) (Figure 5) . Align and lock each cam lock. Install the
Toe Kick (F) by locking the camlockatbothends (Figure5).
5. Installing the Shelves: Insert the shelf clips (d) (Figure 7) into the adjustable shelf holesonthe side
panels (B)atthe desired heightandslideintheshelf (E) .
g
D
e
Figure 1
A
Figure 2
B
B
Figure
4
Figure 3
B
B
C
Figure 6
D
F
B
Figure 5
Top
g
d
Qty 4
ge
Qty 4Qty 2
Figure 7
B

Page 4
1. Place the face frame (A) face downona flatsoftworking surfacetoensure thatthe
faceis not scratched or damaged. (Figure 1) .
2. InstalltheSidePanels(Figure2): Insertrightandleftsidepanels (B) intothegrooves of
thefaceframe (A) andalignthecamlock connectors (Figure2). Lockthe camwitha screwdriver
byturningthescrew180° clockwise (Figure4) .
3. InstalltheBottom and Microwave shelf(Figure3): Gently spreadtheside panels (B)and
insert (C) & (D) intothegroovesofsidepanels (B) untilthey areseated in theface frame (A).
4. Installing theBack PanelandToeKick (Figure5): Beforeyoustartthisstep,putthe
backpanel (E) onaflatsurfacefacingupward.Installthedrawer slide supports (f) inthepre‐
spottedareaonthebackpanel (Figure6). Thebottom of the slide supports should be facing
the bottom groove.Securethemwith2screws each (e)( Figure6).
Theninstallthe backpanel (E)
to the rearofsidepanels (B)(Figure5) .Alignandlockeachcamlock.InstalltheToeKick (F) by
lockin
G
H
8. InstallingtheCornerBraces(Figure10)andinsertingthe Drawer: Placethecorner
braces(b)oneachtopcornerofthecabinetandsecurethemwiththe½”Corner BraceScrews (c).
Slidethedrawerintotherails
andcheckthedrawerposition . Install the rubber bumpers (a) onto
the corners of the door and drawer front (G) where they contact the frame.
Figure 10
b
b c
Q ty 4 Qty 8
6. Install theDrawer SlideRails: Insertthedrawersiderail'sback end(h) intothe
holder(g) previouslyinstalled (Step4) onthebackpanel (D) (Figure 8).
Thensecurethedrawerrailfront endwith1/2” screws(e) usingthepre‐drilled holesinthe
faceframe (A). The remainder of the screws can be used to secure the drawer to the rails.
7. DrawerAssembly(Figure9):First assemblethedrawerfront (G)withdrawerboxfront
(H) withscrews (f).Thenassembletherestpartsofdrawerbox(H) using your palm, or a rubber
mallet if needed, to secure the dove tails into position.
f
Qty 3-5
a
Qty 8
Figure 9
D
F
B
Figure 8
Top
h
g
h
Qty 2 - 1 Set
e
Qty 8

Page5
► Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use abrasive cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metalli
c brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.