CABINETS TO GO Findley & Myers WD2412 User manual

Wall Diagonal Cabinet
ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for Wall Diagonal Cabinets (no shelves)
ITEM# WD2412
Page 1

Item Description Qty
A Face Frame with Door 1
B1 & B2 Front Side Panels (Right & Left) 2
C1 & C2 Rear Side Panels (Right & Left) 2
D Top & Bottom Panels 2
1
E Back Panel
F Hardware box 1
Corner Bracket 135 degree 4pcs, Corner Bracket 90 degree 6pcs, 1" screws for back panel 4pcs
►Instructions:
1. Place the face frame (A) face down on a flat soft working surface to ensure that the face is not scratched or
damaged (Figure 1).
Page 2
1-800-CABINET.
►ItemsQuantity
►General Instructions:
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT
►Requiredtools:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
►Hardware Box:
a b cd
Qty 6
Q ty 20Qty 4 Qty 8
e
Qty 8
f
Qty 4
Qty 2
g
Figure 1
A
B2
D
C2
B1
C1
E
D
A
round bumpers 2pcs, 1/2" flat head screws 20pcs, drywall anchors 8pcs, 2" flat head screws 8pcs
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.

2. Installing the Front Side Panels (B1 & B2): Insert the right and left front side panels into the grooves of face
frame (A) and align the cam lock connectors (Figure 2). Lock the cam lock with a screwdriver by turning the
screw 180° clockwise (Figure 3)
Figure 2
3. Installing the Top and Bottom (Figure 4): Gently spread side panels and insert
grooves of side panels (B1 & B2) until it touches the face frame (A). Well align it and lock each cam.
D
A
A
D C2
4. Installing the Rear Side Panels B-2 (Figure 5) Position the rear side panels (C1 & C2) so that the panel
connectors align to the top panel (D), bottom panel (D), and front side panels (B1 & B2). Gently work the panels
into position. Make sure that it fits well and lock the cam lock connectors. (Figure 3)
5. Installing the Back Panel (Figure 6): Slide the back panel (E) into grooves of rear side panels (C1 & C2) Make
sure the finished side of panel is towards the inside of the cabinet. Once the back panel is assigned and fitted tight,
secure it with 1” Back Panel Screws (c) into the pre-drilled holes on the back panel (Figure 7).
E
C2
C2
Figure 6 Figure 7
6. Installing the corner braces (Figure 8):Place the corner braces (f) on each top front corner and bottom f ront
corner of the cabinet and secure them with 1/2" corner brace screws (b). Attach corner braces (g) where needed.
Figure 8
7. Attach the round bumpers (a) to the inside of the door where it touches the frame.
Page 3
top & bottom panels (D) into the
D
B1
B2
Figure 3
Figure 4
Figure 5
C1
D
c
D
c
Qty 4
b
Q ty 20 Qty 6
f
Qty 4
g
a
Qty 2
d
Qty 8
(d) and (e) are for attaching
the cabinet to the wall.
Qty 8
e
f

Page 4
1. Place the face frame (A) face downona flatsoftworking surfacetoensure thatthe
faceis not scratched or damaged. (Figure 1) .
2. InstalltheSidePanels(Figure2): Insertrightandleftsidepanels (B) intothegrooves of
thefaceframe (A) andalignthecamlock connectors (Figure2). Lockthe camwitha screwdriver
byturningthescrew180° clockwise (Figure4) .
3. InstalltheBottom and Microwave shelf(Figure3): Gently spreadtheside panels (B)and
insert (C) & (D) intothegroovesofsidepanels (B) untilthey areseated in theface frame (A).
4. Installing theBack PanelandToeKick (Figure5): Beforeyoustartthisstep,putthe
backpanel (E) onaflatsurfacefacingupward.Installthedrawer slide supports (f) inthepre‐
spottedareaonthebackpanel (Figure6). Thebottom of the slide supports should be facing
the bottom groove.Securethemwith2screws each (e)( Figure6).
Theninstallthe backpanel (E)
to the rearofsidepanels (B)(Figure5) .Alignandlockeachcamlock.InstalltheToeKick (F) by
lockin
► Maintenance
For daily cleaning, use a dry cloth and a soft l
iquid cleaner.
Never use ab rasive cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.