CABINETS TO GO Findley & Myers DC312 User manual

ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all
3 Drawer Base Cabinets & Vanity Drawer Cabinets
ITEM# DC312, DC315, DC318, DC321, DC324, DC327,
DC330, DC333, DC336 VDC12, VDC15, VDC18 VDC21,
VDC24, VDC27, VDC30, VDC33, VDC36
Page 1

►Items Quantity
Item Description Qty
A
Left Side Panel 1
B
Right Side Panel 1
C Back Panel
1
D Bottom Panel
1
E Frame & 3 Drawer Fronts 1
F
G
Hardware Box
1
Bumper 12pcs, 1/2" Round Head Screws 44pcs, Plastic Corner Brackets 4pcs, 1" Flat Head Screws 12pcs, Glide Brackets 6pcs, Drawer Clips 6pcs
► Required tools:
Page 2
►General Instructions:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
► Hardware Box:
a b
cd
Qty 4 Q ty 12 Qty 44 Qty 12
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
Toe Kick
e f
Q ty 6 Qty 6
H Upper Drawer Panel & Drawer Box: (Front, Back, Sides, & Bottom)
Drawer Glides
3 Sets
1 Set
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.
2 Sets
I Lower Drawer Panels & Drawer Boxes: (Fronts, Backs, Sides, & Bottoms)

C
A
B
E
1
2
c X12
e X6
Assemble the Side Panels (A,B) onto the
Frame (E) by connecting the male and
female cam locks and using a screwdriver
to turn the lock clockwise. (Figure 1)
{ NOTE: Lay Frame and Doors on a flat smooth soft
work surface to assemble. }
SoftSurface
Hard Surface
E
E
Install the glide brackets
(e) to the Back Panel (C)
using screws (c).
(Figure 2)
Page 3
Figure 1
Figure 2

F
D
3
4
Figure 3
Insert the Bottom Panel (D)
into the groove of the Side
Panels and Frame.
(Figure 3)
Figure 4
Install the toe kick (F) onto
the side panels (A,B) and
lock the cam locks.
(Figure 4)
Page 4

G
C
5
6
Figure 6
Page 5
Figure 5
Install the Back Panel (C)
onto the side panels (A,B)
and lock the cam locks.
(Figure 5)
Attach the Drawer Glides (G)
using screws (c) onto the
frame and glide brackets
installed in Step 2. (Figure 6)
cX6

H
d X4
b X4
7
8
H
Figure 8
Page 6
Figure 7
Finish assembling the
drawer boxes. (H) (Figure 8)
{ NOTE: You may use a rubber
mallet if needed to seat the
dove tails. }
Optional Tools: Rubber Mallet
Assemble the drawer front (H)
onto the drawer box front
using the supplied screws
(b). Place bumpers (d) onto
the corners of the drawer
front. (Figure 7)
d

d
b x8
X8
d
10
9
c X6
f X2
Figure 9
Figure 10
Attach the Drawer Clips (f) using
screws (c) onto the bottom of the
drawers. (H) (Figure 9)
Assemble the drawer front (I)
onto the drawer box front
using the supplied screws
(b). Place bumpers (d) onto
the corners of the drawer
front. (Figure 10)
Page 7
H
I

X12
X4
f
I
11
12
I
Figure 12
Page 8
Figure 11
Finish assembling the
drawer boxes. (I) (Figure 11)
{ NOTE: You may use a rubber
mallet if needed to seat the
dove tails. }
Optional Tools: Rubber Mallet
Attach the Drawer Clips (f) using
screws (c) onto the bottom of the
drawers. (I) (Figure 12)
c

13
X8
X4
14
a
c
Install the corner
brackets (a) using
screws (c) in the four
top corners.
(Figure 13)
Insert the assembled drawers
(H,I) onto the glides. Push in
until you hear clicks from the
drawer clips locking into the
glides. (Figure 14)
Figure 13
Figure 14
Page 9

Page 10
►Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use abrasive cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets
etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by
email - [email protected] or call 1-800-CABINET.