CABINETS TO GO Findley & Myers BBC42 User manual

ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all Blind Base Cabinets
ITEM# BBC42, BBC45
Page 1

►Items Quantity
Item Description Qty
A
Left Side Panel 1
B
Right Side Panel 1
C Back Panel
1
D Bottom Panel
1
E Frame & Door 1
F Shelf 1
G
Hardware Box
1
Bumper 6pcs, Shelf Bracket 4pcs, 1/2" Round Head Screws 20pcs, Plastic Corner Brackets 4pcs, 1" Flat Head Screws 4pcs, Glide Brackets 2pcs, Drawer Clips 2pcs
► Required tools:
Page 2
►General Instructions:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
► Hardware Box:
a b
cd
Qty 4 Q ty 4 Qty 20 Qty 6
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.
Toe Kick
e f g
Q ty 4 Qty 2Qty 2
H Drawer Panel & Drawer Box: (Front, Back, Sides, & Bottom)
I Drawer Glides
1 Set
1 Set

A
B
E
2
D
1
►Instructions:
SoftSurface
Hard Surface
E
E
Assemble the Right & Left Panels (A,B)
onto Frame (E) by connecting the male and
female cam locks and using a screwdriver
to turn the lock clockwise.
(Figure 1) {NOTE: Lay Frame and Door on a flat
smooth soft work surface to assemble.}
Insert the Bottom Panel (D)
into the groove of the Side
Panels and Frame.
(Figure 2)
Figure 1
Figure 2
Page 3

3
f X2
G
4
C
b X4
Install the glide brackets (f) to
the Back Panel (C). (Figure 3)
{NOTE: The drawing depicts a left
drawer installation. The brackets
can be installed for either side.}
Figure 3
Figure 4
Page 4
Install the toe kick (G) onto
the side panels (A,B) and
lock the cam locks.
(Figure 4)

C
5
6
a X4
A,B
Figure 5
Install the Back Panel (C)
onto the side panels (A,B)
and lock the cam locks.
(Figure 5)
Insert the shelf brackets (a)
into the side panels (A,B)
in the location of your
choosing. (Figure 6)
Figure 6
Page 5

8
X4
c
X4
d
7
F
d
Insert the shelf (F) into the
shelf brackets installed in
Step 6. (Figure 7)
Figure 7
Figure 8
Page 6
H
Assemble the drawer front
(H)onto the drawer box
front using the supplied
screws (c). Place bumpers
(d) onto the corners of the
drawer front. (Figure 8)

H
9
10
X2
g
X6
c
Finish assembling the
drawer box. (H) (Figure 9)
{ NOTE: You may use a
rubber mallet if needed to
seat the dove tails. }
Figure 9
Optional Tools: Rubber Mallet
Figure 10
Attach the Drawer Clips (g) using
screws (c) onto the bottom of the
drawer. (H) (Figure 10)
Page 7
H

X4
X8
12
11
X2
X1
I
I
Figure 11
Figure 12
Page 8
Attach the Drawer Glides (I) using
screws (c) onto the frame and
glide brackets installed in Step 3.
(Figure 11)
c
Install the corner brackets (e)
using screws (c) in the four top
corners. (Figure 12)
e
c

X2
d
13
14
Figure 14
Page 9
Figure 13
Install the remaining bumpers (d)
onto the corner of the door where
it comes in contact with the
frame as shown. (Figure 13)
d
Insert the assembled drawer (H)
onto the glides. Push in until you
hear clicks from the drawer clips
locking into the glides. (Figure 14)
H

►Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use abrasive cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets
etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by
email - [email protected] or call 1-800-CABINET.
Page 10