CABINETS TO GO Findley & Myers SB36 User manual

ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all Sink Base Cabinets
ITEM# SB36, VSB36
Page 1

►Items Quantity
Item Description Qty
A
Left Side Panel 1
B
Right Side Panel 1
C Frame & Doors: (2 Lower Doors, 2 False Drawer Fronts)
1 Set
D Top Back Panel
1
E Bottom Back Panel 1
F Bottom Panel 1
G
Hardware Box
1
Bumper 4pcs, 1/2" Round Head Screws 8pcs, Plastic Corner Brackets 4pcs
► Required tools:
Page 2
►General Instructions:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
► Hardware Box:
a
bc
Qty 4 Qty 8Qty 4
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
Toe Kick
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.

F
A
B
C
1
2
SoftSurface
Hard Surface
C
C
Assemble the Side Panels (A,B) onto the
Frame (C) by connecting the male and
female cam locks and using a screwdriver
to turn the lock clockwise. (Figure 1)
{ NOTE: Lay Frame and Door on a flat smooth soft
work surface to assemble. }
Figure 2
Page 3
Insert the Bottom Panel (F)
into the groove of the Side
Panels and Frame.
(Figure 2)
Figure 1

D
E
G
3
4
Figure 3
Figure 4
Page 4
Install the toe kick (G) onto
the side panels (A,B) and
lock the cam locks.
(Figure 3)
Install the Back Panels (D,E)
onto the side panels (A,B)
and lock the cam locks.
(Figure 4)

X4
a
5
b X8
6
c X4
c
Install the corner brackets (a)
in the four top corners using
screws (b).
(Figure 5)
Figure 5
Install the bumpers (c) onto the
corner of the doors where they
come in contact with the frame.
(Figure 6)
Figure 6
Page 5

►Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use abrasive cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets
etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to
get the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care
by email - [email protected] or call 1-800-CABINET.
Page 6