CABINETS TO GO WC2430 User manual

ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all Wall Cabinets
with 2 Doors & 2 Shelves
ITEM# WC2430, WC2730, WC3030, WC3330, WC3630
WC2436, WC2736, WC3036, WC3336, WC3636
Page 1

►Items Quantity
Item Description Qty
A
Left Side Panel 1
B
Right Side Panel 1
C Back Panel
1
D Top & Bottom Panel
2
E Frame & Door 1 Set
F Shelves 2
Hardware Box
Shelf Clips 8pcs, ST25mm Screws 4pcs, Metal 90° Brackets 4pcs, 1/2" Round Head Screws 8pcs, Bumpers 4pcs, ST62mm Screws 4pcs, Wall Anchors 4pcs
► Required tools:
Page 2
►General Instructions:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
► Hardware Box:
a
bc
Qty 8Qty 4Qty 4
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
d
Q ty 8
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.
e
Q ty 4
f
Q ty 4
g
Q ty 4

E
D
B
A
1
2
Page 3
Figure 1
SoftSurface
Hard Surface
B
B
Assemble the Side Panels (A,B) onto the
Panels (D) by connecting the male and
female cam locks and using a screwdriver
to turn the lock clockwise. (Figure 1)
{ NOTE: Lay cabinet parts on a flat smooth soft
work surface to assemble. }
Attach the Frame (E) to the
assembled panels.
(Figure 2)
Figure 2
D

C
3
4
Figure 4
Page 4
Figure 3
Install the Back Panel (C) by
sliding it into the groove.
(Figure 3)
Attach the Back Panel
(C) using screws (b).
(Figure 4)
b
Qty 4
C

e
5
6
Figure 6
Page 5
Figure 5
Install the shelf clips (a) into the desired
locations of your choosing. Insert the
shelves (F) onto the clips. Install the
bumpers (e) onto the door at the
corners where it comes in contact with
the frame. (Figure 6)
Install the metal brackets
(c) using screws (d) to the
corners of the frame and
side panels on the top and
bottom of the cabinet.
(Figure 5)
c
Qty 4
d
Q ty 8
a
a
Qty 8
e
Q ty 2
F
F

►Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use abrasive cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets
etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by
email - [email protected] or call 1-800-CABINET.
Page 6