CABINETS TO GO Findley & Myers DC224 User manual

Page 1
2DrawerBaseCabinet 
ASSEMBLY INSTRUCTIONS
Theseassemblyinstructionsare onlyapplicableforall2drawerbasecabinets.
ITEM #DC224,DC230,DC236

Page 2
►Items Quantity
Item Description Qty
AFaceFrame 1
BSidePanels 2
CBottomPanel 1
DBackPanel 1
E1
FToeKick 2
G
HDrawerBoxes: Front 3pcs, Back 3pcs, Sides 6pcs, Bottom 3pcs 2
HardwareBox: 1
Bumpers8pcs,Plasticcornerbracket4pcs,1/2"roundheadscrews8pcs,1/2"flatheadscrewsforslides12pcs
1"screw12pcs, Slide Rails 2 Sets, Slide Rail Supports 4pcs
►General Instructions:
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT
1-800-CABINET.
►Required Tools:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
►Hardware Box:
a b fd
Qty 12
e
Qty 12
c
g
Qty 4Qty 4 - (2 Sets) Qty 8 Q ty 4 Qty 8
G
AF
G
E
B
D
B
C
DrawerFronts
x2
F
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.

Page 3
►Instructions:
1. Placethefaceframe (A) facedownon aflatsoftworkingsurfacetoensurethatthefaceis 
notscratchedordamaged (Figure1) .
2. InstallingtheSideP anels(Figure2): Insertrightandleftsidepanels (B) intothegrooves of
the face frame (A) and align the cam lock connectors (Figure 2). Lock the cam
withascrew driver byturningthe screw180°clockwise (Figure4) .
3. Ins tallingtheBottom(Figure3): Gentlyspreadthesidepanelsandinsertthebottom (C)
intothegrooves ofsidepanels (B) untilitis seated inthefaceframe (A). Alignitandlocke
achcam.
4. InstallingtheBackPanelandToeKick(Figure5): Before youstartthis step,placethe
backpanel (D) onaflatsurfacefacingupward.Installthedrawerrailholders (f) inthepre‐ 
spotted area on the back panel (Figure 6). Securethemwith2flatheadscrews (e) ( Figure6). Then
putthebackpanel (D) atrear of side panels (B) (Figure 5) . Align and lock each cam lock. Install the
Toe Kick (E) by locking the camlockatbothends (Figure5).
f
D
e
Figure 1
A
Figure 2
B
B
Figure
4
Figure 3
B
B
C
Figure 6
D
E
B
Figure 5
Top
f
fe
Qty 8Qty 4

Page 4
1. Place the face frame (A) face downona flatsoftworking surfacetoensure thatthe
faceis not scratched or damaged. (Figure 1) .
2. InstalltheSidePanels(Figure2): Insertrightandleftsidepanels (B) intothegrooves of
thefaceframe (A) andalignthecamlock connectors (Figure2). Lockthe camwithascrewdriver
byturningthescrew180° clockwise (Figure4) .
3. InstalltheBottom and Microwave shelf(Figure3): Gently spreadtheside panels (B)and
insert (C) & (D) intothegroovesofsidepanels (B) untilthey areseated in theface frame (A).
4. Installing theBack PanelandToeKick (Figure5): Beforeyoustartthisstep,putthe
backpanel (E) onaflatsurfacefacingupward.Installthedrawer slide supports (f) inthepre‐
spottedareaonthebackpanel (Figure6). Thebottom of the slide supports should be facing
the bottom groove.Securethemwith2screws each (e)( Figure6).
Theninstallthe backpanel (E)
to the rearofsidepanels (B)(Figure5) .Alignandlockeachcamlock.InstalltheToeKick (F) by
lockin
F
G
7. InstallingtheCornerBraces(Figure10)andinsertingthe Drawer: Placethecorner
braces(b)oneachtopcornerofthecabinetandsecurethemwiththe½”Corner BraceScrews (c).
Slidethedrawerintotherailsandcheckthedrawerposition . Install the rubber bumpers (a) onto
the corners of the door and drawer front (F) where they contact the frame.
Figure 10
b
b c
Q ty 4 Qty 8
5. Install theDrawer SlideRails: Insertthedrawersiderail'sback end(g) intothe
holder(f) previouslyinstalled (Step4) onthebackpanel (D) (Figure 8).
Thensecurethedrawerrailfront endwith1/2” screws(e) usingthepre‐drilled holesinthe
faceframe (A).
6. DrawerAssembly(Figure9):First assemblethedrawerfront (F)withdrawerboxfront (G)
withscrews (d).Thenassembletherestpartsofdrawerbox(G) using your palm, or a rubber
mallet if needed, to secure the dove tails into position. Repeat steps for remaining drawers.
d
Qty 5-6 each
a
Qty 12
Figure 9
D
E
B
Figure 8
Top
gf
g
Qty 4 - 2 Set
e
Qty 4

Page5
► Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use abrasive cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metallic brushes, and other
products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the q uality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.