Canon Creative Park Pop-up Card Christmas House User manual

Pa rt A
Pa rt B
Pa rt C Pa rt D Pa rt I
Pa rt M
Pa rt N Pa rt O
Pa rt P
Pa rt J
Pa rt K Pa rt L
Pa rt E
Pa rt F
Pa rt G
Pa rt H
Cut out the parts and fold them along the fold lines on each.
PAGE01
For part B also, fold back the longest glue tab on the bottom edge and glue it to the reverse side.
Fold back the longest glue tab on the bottom edge of part A, and glue it to the reverse side.
Pop-up Card(Christmas house): Assembly Instructions

PAGE02
Fold back the top part of part D along the fold line, and glue it to the reverse side.
Fold back the glue tab at the bottom of the piece you made in 8 along the fold
line, and glue it to the reverse side.
Fold back the vertical piece along the fold line, and glue it to the reverse side.
Connect the part you made in 5 together at the glue tabs.
As shown in the picture, attach the left glue tab on part B to the wall glue tab on part A.
Fold up the parts you glued together in 4 as shown in the picture, while attach-
ing the right glue tab on part A to the back of part B.
Pop-up Card(Christmas house): Assembly Instructions

PAGE03
Fold part C down the middle and glue together at the back.
At the fold line, fold back the vertical glue tab at the bottom of the piece you m-
ade in 14, and glue it to the reverse side.
Fold back the horizontal glue tab at the bottom of part F (marked ) and glue
it to the reverse side.
Join the chimney together at the glue tabs.
Attach part E.
Insert the piece you made in 9 into the piece you made in 6, in line with the po-
sition of the chimney on 6. Then glue 9 to the glue tabs on the bottom inside of 6.
Pop-up Card(Christmas house): Assembly Instructions

Insert the chimney you made in 12 through the hole in part F, and secure it by
gluing at the left and right glue tabs on part F.
PAGE04
Fold back the top glue tab (marked ) on part F at the fold line, and glue it to the
reverse side. Then attach the glue tab on the vertical piece to the back of part F.
Pass the part you made in 13 through the vertical strip on the back bottom edge of
part F as shown in the photo, and secure it to the glue tabs on the back of the wall.
Glue the glue tab on the piece you made in 15 to the reverse side of part F.
Fold back the left glue tab (marked ) on part F at the fold line, and glue it to
the reverse side.
Fold back the right glue tab (marked ) on part F at the fold line, and glue it to
the reverse side.
Pop-up Card(Christmas house): Assembly Instructions

PAGE05
Fold part I down the middle and glue together at the back.
Pass the piece you made in 25 through the vertical strip on the top back edge of
part F as shown in the photo, and secure its glue tabs to the reverse side of the roof.
As shown in the picture, attach the piece you made in 23 to the reverse side of the wall.
Attach part G to the roof.
Fold back the bottom glue tab on part H (marked ) and glue it to the reverse side.
Pop-up Card(Christmas house): Assembly Instructions

PAGE06
After gluing, carefully fold it up and open and close the card a few times to ch-
eck the mechanism.
Attach part L to part K.
Attach the glue tabs on part K to part J and the base, at the glue spots.
Attach the glue tabs on the piece you made in 27 to the base, slotting it onto
the slit at the back.
Attach the right glue tab on part J to the glue tab at the back left corner of the house.
Join the left and right sides of the base together at the glue tabs.
Pop-up Card(Christmas house): Assembly Instructions

PAGE07
Insert the bottom glue tabs of the part you made in 36 through the slits on the
base, and attach them to the reverse side.
After gluing, carefully fold it up and open and close the card a few times to ch-
eck the mechanism.
Glue the cover with the writing on it to the left half of the base.
39 is the completed card when the cover is stuck on to the other half side.
Fold back the second glue tab from the left and right on the bottom of part M,
and glue them to the reverse side (the parts in the photo only).
Attach the left glue tab on part M to the left glue tab on the back of part N.
Fit part O to the slot on part N, and attach the right glue tab on part M to the
back of the right side of part O.
Fit part P to the top of part N, parallel to part N, and attach it at the back, to the
glue spot on part N.
Pop-up Card(Christmas house): Assembly Instructions