Canon PAPER CRAFT Moving Tiger through o ring of... User manual

Assembly Instructions
Mountain fold(dotted line)
Make a mountain fold.
Valley fold(dashed and dotted line)
Make a valley fold.
Scissors line(solid line)
Cut along the line.
Cut in line(solid line)
Cut along the line.
Glue spot(Red dot)
Glue parts with the same number together.
Glue spot(Green dot)
Glue within the same part.
Glue spot(Blue dot)
Glue to the rear of the other part.
Glue
The glue spot(colored dot)
shows where to apply the glue.
Tools and materials
Assembly tip
Caution
Scissors, set square, glue(We recommend stick glue), pencil, used
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Before gluing, crease the paper along mountain fold and valley
fold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.
View of completed model
Assembly Instructions : Six A4 sheets (No. 1 to No. 6)
*Pull on the lever at right to
make the tiger jump through
a ring of fire and to make
the clowns lift their flags.
*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold.
Note:
The tiger uses about 20 centimeters of string to jump through the ring of fire. Be sure to use strong string made of silk or similar material.
Before starting assembly: Writing the number of each section on its back side
before cutting out the sections is highly recommended.
(* This way, you can be sure which section is which even after cutting out
the sections.)
Indicates where sections should
be glued together.
Indicates where to insert sections.
Do not glue the sections together.
Glue part 7 to the reverse
side of part 6.
Cut along the line.
Use care here.
Round bar: Use to give parts a curved surface.
Tweezers: Useful in working with fine parts.
(Moving) Tiger through a ring of fire : Assembly Instructions
http://www.canon.com/c-park/en/
* Build the model by carefully reading the Assembly Instructions , in the parts sheet page order.
©Canon Inc. ©Hideharu Naitoh & F design

Using a round bar
or similar item makes
it easier to assemble
the round pillars.
Note: Glue this part together after assembling
the completed parts 13 and 18.
Glue this piece in place so that it fits precisely
into the windows cut in parts 1 and 10.
*Use glue on the window surface only.
Do not glue the sides.
(Moving) Tiger through a ring of fire : Assembly Instructions ©Canon Inc. ©Hideharu Naitoh & F design

Note: Avoid using glue on
the entire surface, since this
could cause the part to warp.
Open the notch slightly
to the left and right.
Parts , , and
Parts , , and 15
Note: Glue the remaining surface
through which the lever runs here.
(Moving) Tiger through a ring of fire : Assembly Instructions ©Canon Inc. ©Hideharu Naitoh & F design

Use about 20 centimeters
of string.
Attach the string by
inserting it into the hole as
shown in the illustration.
Glue the reverse sides together.
Glue together only the tips of
the clown’s cap and hands.
With the parts in positions A, B, and C
as shown in the illustration, run the string
through part 10 and pull it out.
Next, run the string through the hole in
part 18.
Now pull and push part A to check how
it moves.
Next, fix the string in position by gluing
part 19 in place on both sides.
(Moving) Tiger through a ring of fire : Assembly Instructions
Parts , , and
©Canon Inc. ©Hideharu Naitoh & F design

Parts and
(Moving) Tiger through a ring of fire : Assembly Instructions ©Canon Inc. ©Hideharu Naitoh & F design

Glue in place between
the two sides of part 38.
(Position the mark in front.)
Slightly curve the surfaces
of parts 36 and 38 using
a round bar or similar item.
Glue to the reverse
side of part 38.
Place the tiger’s front paws at the
center of the hexagonal stand,
as shown in the illustration.
Attach the rear legs to
this part in this position.
Finished!
(Moving) Tiger through a ring of fire : Assembly Instructions ©Canon Inc. ©Hideharu Naitoh & F design