Cardinal Health SVED PW596 User manual

© 2020 Cardinal Health. All Rights Reserved. CARDINAL HEALTH, the Cardinal Health LOGO, ESSENTIAL TO CARE and SVED® are trademarks or registered
trademarks of Cardinal Health and may be registered in the US and/or in other countries. All other marks are the property of their respective owners.
Negative Pressure Wound Therapy
Cardinal Health™SVED
®
Clinician Quick Reference Guide
PW 596
Rev 01/21
Canister
ON Button
OFF Button
Canister Full Alert
Pressure Settings
Battery Charging Port
Canister Holder
Canister Release Button
Plugged In
Power/Charging Status
Therapy Timer/Display
Low Pressure/Leak Alert
Insert Canister
Turning the SVED® OFF
To turn the SVED® o, press the OFF Button.
NOTE: Please refer to the Cardinal Health™ SVED® CLINICIAN User Manual for
detailed instructions and review the Precautions and Contraindications before use.
This can be found at www.infusystem.com/npwt.
Insert canister in holder by sliding it up into bottom of the Canister Holder. Line up
the two short ports with the Canister Holder and press until it “clicks” into place and
locks. To remove canister, press Canister Release Button, grasp canister at bottom
and pull downward.
Intermittent Mode
To operate the SVED® in Intermittent Mode, press and hold the desired Pressure
Setting Button then momentarily press the OFF Button. The ON Button
begins ashing and the SVED® beeps twice indicating the SVED® is now operating in
Intermittent Mode. Release both buttons. Repeat process to return to Continuous
Mode.
Troubleshooting Alerts
If the SVED® begins to alert, please refer to troubleshooting table on the back.
Therapy Lockout
To lock therapy setting, press and hold the desired Pressure Setting Button for 3
seconds. The SVED® beeps three times indicating therapeutic setting is locked.
Repeat process to unlock therapy setting.
Turning the SVED® ON
Press the ON Button to start therapy. Select desired negative pressure wound
therapy setting by pressing the corresponding Pressure Setting -70, -120, or
-150mmHg button. The Pressure Setting Button ashes until desired
pressure is reached, after which the button remains lit.
Connect the Dressing
Connect the blue end of the tubing to the open port of the canister. Gently twist and
push connector on just enough to seal it. Make sure that the clamp on the tubing is
open.
NOTE: Please refer to the Cardinal Health™ SVED® Clinician User Manual for
instructions on how to properly dress the wound and troubleshoot issues.
Questions? Contact InfuSystem NPWT Clinical Support
[phone]
Notice to Users: As with any prescription medical device, failure to follow
product instructions or adjusting settings and performing therapy applications
without the express direction and/or supervision of your trained clinical
caregiver may lead to improper product performance and the potential for
serious or fatal injury.
Debrillation: Remove the wound dressing if debrillation is required in the
area of dressing placement. Failure to remove the dressing may inhibit
electrical current transmission and/or patient resuscitation.
Magnetic Resonance Imaging (MRI): The SVED® is not MRI-compatible. Do
not take into the MRI area.
Hyperbaric Oxygen Therapy (HBO): NEVER allow an SVED® — whether on or
o — inside a hyperbaric chamber. The SVED® must be disconnected from the
patient prior to HBO treatment.
In partnership with
For more information and videos visit our website at
www.infusystem.com/npwt

TROUBLESHOOTING
PW 596
Rev 01/21
What you see or hear Problem What to do More information
OFF Button is ashing.
Single beep.
The battery is low and has
approximately 30 minutes
before the battery will be
too low to support continued
operation of the SVED®.
Use only the A.C. Power Adapter that came
with the SVED®.
LOW PRESSURE/LEAK
indicator is lit.
Single beep.
Pressure Setting Button
is ashing.
SVED® is making more noise.
There is an air leak in either
the dressing or the tubing
connections.
Leaks often occur over areas
of moist skin, creases or folds
in skin and wrinkles in the
drape.They can occur if the
drape snags on clothing or
bedsheets.
Once the leak is found and sealed, the alert
resets, the Pressure Setting Button quits
ashing and the SVED® becomes quiet.
If the alert continues, call InfuSystem
NPWT Clinical Support at [phone] for
more assistance.
If the alert continues, call InfuSystem
NPWT Clinical Support at [phone] for
more assistance.
CANISTER FULL
indicator is lit.
Single beep.
The canister is full. • Visually assess the canister to see if it is full.
If the canister is full, change the canister.
•
pressing the OFF Button and then turn the
SVED® back on to resume therapy.
The Canister Full alert begins when the
canister is 90 percent full, but the SVED®
continues to work until the canister
completely lls.
entering the canister will cause a false Canister
Full alert and the canister must be changed.
If alert continues, call InfuSystem NPWT Clinical
Support at [phone] for more assistance.
Pressure Setting will not
change.
Setting has been locked.
SVED® is quiet and uid is not
moving in the tubing.
This is NOT a problem. The
dressing has a good seal and
the SVED® is maintaining
target pressure.
No action needed.
Unlock the device.
ON Button is ashing.
This is NOT a problem.
The SVED® is in
Intermittent Mode.
No action needed.
CAUTION: In the event of an emergency, please contact your treating physician, caregiver or your local emergency responders.
If the canister is not full, turn the SVED® o by
If the SVED® is placed on its front, uid
© 2020 Cardinal Health. All Rights Reserved. CARDINAL HEALTH, the Cardinal Health LOGO, ESSENTIAL TO CARE and SVED® are trademarks or registered
trademarks of Cardinal Health and may be registered in the US and/or in other countries. All other marks are the property of their respective owners.
• Plug in the SVED®. A green light shows next to
Plugged In indicator and an amber light next
to Battery Charging indicates that power is
going to the SVED®. The amber light turns o
after the battery is fully charged.
• Clamp the tubing.
• If Low Pressure/Leak light stops and Canister
Full light begins ashing, there is a leak
between the clamp and the dressing — often
in the dressing. Reopen the clamp before
addressing the leak.
• Gently press around drape to check for leaks.
If leak is found, patch with extra drape material
or drape strips.
• If Low Pressure/Leak Alert continues, there is a
leak between the clamp and the SVED®. Check
the tubing connection at the canister. Check to
ensure that the canister is fully seated and
locked. Check for cracks in the canister or lid
separation. If found, replace the canister.
• Open the clamp.
Intermittent Mode maintains target pressure
for 5 minutes and decreases to -25mmHg for 2
minutes. To change from Continuous to
Intermittent Mode, press and hold the Pressure
Setting Button and tap the OFF Button.
Repeat to change back to Continuous Mode.