Cardinal Health Kangaroo Joey User manual

Pump Set Loading Procedure.
6. Close blue door. Display
should read SETLOADED.
3. With pump display facing you
open blue door at top of pump.
4. Grasp finger tab on valve and insert
valve into valve slot on the left.
5. Grasp black ring retainer, and gently
wrap tubing anti-clockwise around
rotor. Pull up retainer and insert
into slot.
1. Locate power button on lower
right hand corner of control panel.
Press to turn pump on.
2. Confirm if you want to KEEP or
CLEAR any prior pump settings.
Kangaroo™ Joey Enteral Feeding Pump
User Guide (Feed & Hydration Mode)

1. Press PRIME PUMP followed by
AUTO PRIME to automatically prime
or HOLD TO PRIME to manually prime
both feed and flush lines.
Press DONE when complete.
2. Press ADJUST FEED followed
by FEED RATE to adjust hourly
delivery rate.
3. Press buttons on left to program hourly
feed rate. Press ENTER to confirm rate.
4. Press FEED VTBD to program feed
Volume To Be Delivered if desired.
5. Press buttons on left to program volume
of feed to be delivered. Press ENTER to
confirm rate, followed by DONE to return
to main screen.
6. Press ADJUST FLUSH to program
flush volume and interval.
Set Priming and Pump Programming Procedure.
POWER DOWN PROCEDURE
Locate power button on lower right hand corner of control panel. Press and hold power button until the pump display turns off.

7. Press FLUSH VOLUME to program
flush volume. Press FLUSH INTERVAL to
program interval between each flush.
8. Press buttons on left to program
volume of flush to be delivered. Press
ENTER to confirm volume.
9. Press buttons on left to program
flush interval. Press ENTER to confirm
interval , followed by DONE to return
to main screen.
10. Press RUN to commence feeding regime.
In order to achieve proper accuracy, the initial
fluid line in the feeding set container must
be 15 cm above the top of the feeding pump
when initiating the feeding cycle.
* IMPORTANT NOTE. Kangaroo
™
Joey Pump will automatically flush an additional
25mL of water after completing the programmed delivery of formula, as long as at
least one flush has occured during formula delivery.
Locate power button on lower right hand corner of control panel. Press and hold power button until the pump display turns off.
15 cm

Alarm and Error Code Information.
HOLD ERROR
Pump left in Hold for more
than 10 minutes.
Press CONTINUE followed
by RUN to start pump running
or power down pump.
ROTOR ERROR
Problem with pump set
tubing around the rotor.
Ensure silicone tubing
is correctly loaded
around rotor.
FLOW ERROR
Obstruction in line
downstream from pump.
Check for kinked or blocked
tubing below pump and rectify.
FEED ERROR
Feed container empty or
obstruction in the line
upstream from pump.
Check for kinked tubing or
obstruction in line above pump
or attach new/refilled feed
container.
FEEDING COMPLETE
Programmed feed has
been delivered.
Power down pump.
FLUSH ERROR
Water container empty
or obstruction in the line
upstream from pump.
Check for kinked tubing
or obstruction in flush
line above pump or refill
flush container.
PUMP SET DISLODGED
Black retainer ring (MISTIC)
is not properly loaded in
MISTIC pocket.
Ensure pump set is
correctly loaded.
BATTERY LOW
Battery must be
recharged immediately.
Plug power cord
into AC outlet.
SYSTEM ERROR
General error - see
pump manual.
Send pump for service.
cardinalhealth.com.au
Cardinal Health Australia
Level 2, 5 Eden Park Drive, North Ryde NSW 2113
© 2019 Cardinal Health. All Rights Reserved. CARDINAL HEALTH, the Cardinal Health LOGO and ESSENTIAL
TO CARE are trademarks of Cardinal Health and may be registered in the US and/or in other countries.
All other marks are the property of their respective owners. 1432-03-19
For complete operation information please refer to Kangaroo™
Joey enteral feeding pump operation and service manual