CareCo abilize strider sport MS01066 User manual

Code: MS01066
Instruction Booklet

Introduction
Important Precautions
Identication of Parts
Charging the Batteries
Disassembling your Scooter
Troubleshooting
Caution
Safety Information on
Electromagnetic Interference (EMI)
Specications
Warranty
Table of Contents
2
3
4
8
9
10
11
12
14
15
Instruction Booklet: Contents
01

Thank you and congratulations on purchasing your new Abilize Mobility Scooter.
It is designed to provide you with transportation ability indoors and outdoors.
We pride ourselves on providing safe and comfortable products. Our goal is to ensure your
complete satisfaction. We sincerely hope you enjoy your Abilize Mobility Scooter.
Please read and observe all warnings and instructions provided in owner’s manual before
you operate the various functions of this scooter. Also, please retain this booklet for future
reference.
IF YOU HAVE ANY QUESTIONS, YOU CAN CONTACT:
UK Authorised Dealer
CareCo UK Ltd
Hubert Road
Brentwood
Essex
CM14 4JE
Tel: [phone]
Email: [email protected]
Information of European Representation
EMERGO EUROPE
Molenstraat 15
2513 BH, The Hague
The Netherlands
Instruction Booklet: Introduction
02

Instruction Booklet: Important Precautions
03
• Only one person at a time can ride the Scooter.
• Maximum load is 136 kg / 300 Ibs pounds.
• Turn key off before getting on or off.
• Always drive carefully and be aware of others using the same area.
• Always use pedestrian crossings wherever possible. Take extreme care when crossing roads.
• Do not drive on slope exceeding 8 degree, and take extreme care when turning on slope.
• Do not use full power when turning to sharp corner.
• Take great care and drive in low speed when backing up, riding downhill or on uneven surface,
and climbing curb.
• Please use the lowest speed when driving through a descending road or uneven terrain. If
speed is too fast, leave your hand off the handle bar, let the scooter stop. Make sure you are
safe and start again.
• The weight capacity limit can be different depending on ramp degree.
• A slow speed must always be used when ascending, descending or traversing a slope or
incline and also on uneven terrain, ramps and soft or loose surfaces, such as gravel or grass.
• To prevent any danger, do not turn around at high speed while ascending or descending
a ramp.
• Scooter may not operate well in high humidity.
• Do not leave the powered scooter in a rain storm of any kind.
• Direct exposure to rain or dampness will cause the scooter to malfunction electrically and
mechanically; may cause the powered scooter to prematurely rust.
• Never put scooter in neutral when staying on slopes.
• Follow trafc laws when riding outside.
• When scooter is on moving transport vehicles, do not sit or stay on scooter.

Instruction Booklet: Identification of Parts
04
Before attempting to drive this scooter on your own, it is important that you familiarize
yourself with the controls and how to operate them.
Figure 1 - Front View
Figure 2 - Top Control Panel Figure 3 - Back View
Changing Sockets
LED Headlight
Solid Tyres
Circuit Breaker
Reector
Seat Rotation
Lever
Front Basket
Flip-Up Armrests
Padded Foldable Seat
Easy-To-Operate Control
Panel and Delta Handlebar
Self-Diagnostic Warning Light Rear Light (Optional Accessory)
Anti-Tip Wheels
Horn Button
Battery Gauge
Free-
Wheeling
Level
Reectors
Speed Dial Knob
Main Key Switch
Throttle

Before operation, please remove the Lock Nut (A) and press button of Circuit Breaker (B) to
activate the system.
Function of Parts:
Main Key Switch (C)
• Turn the key to the right to turn the scooter on.
• Turn the key to the left to turn the scooter and
LED light on.
• Turn the key to the centre position to turn the
scooter off.
CAUTION: Always ensure that the scooter is switched off before getting on or off the
scooter and before removing any items of the scooter.
CAUTION: Turning the scooter OFF whilst driving will bring the scooter to an abrupt stop.
Speed Dial Knob (D)
The rabbit icon indicates fast or high speed. The turtle icon indicates slow or low speed. By turning
this Knob (D) towards chosen icon you can control the overall speed of the scooter.
CAUTION: Before driving the scooter, set the speed to low speed by turning the knob
towards turtle icon.
CAUTION: Drive in high speed when encounter an up slope, and drive in low speed when
encounter a down slope.
Horn Button (E)
Press Horn Button (E) once to sound warning tone when necessary.
Battery Gauge (F)
The LEDs represents an approximation of battery capacity. If the charge is full, all LEDs are lit.
When only red and orange LEDs are lit, the batteries are consuming and should be charged soon.
When only red LEDs are lit, charge the batteries immediately.
Self Diagnostic Warning Light (G)
Flashing light indicates there is a problem within scooter. See page 11 for more information.
Throttle (H) (H1)
To move forward by pulling the right side of Throttle (H). To move backward by pulling the left side
of Throttle (H1). (The movement directions can be reversed by local dealers if required.) Releasing
the throttle to engage automatic brake. These are also your accelerator, the further you pull it, the
faster you go. (Subject to the position of the Rabbit/Turtle control).
CAUTION: Releasing the throttle engages the automatic brake, but will taxi for a short
buffering distance, please keep safe distance when stopping to prevent any danger.
Instruction Booklet: Identification of Parts
05
A
C
D
F
G
E
H
B

Tiller Angle Adjustment:.
• Turn the Cap (I) outward upward to disengage the pin.
• Simultaneously, adjust the tiller fore-and-aft to the most comfortable angle. Release Cap (I) and
ensure the pin is fully engaged to lock the tiller in position.
Seat Rotation Adjustment:.
• Lift the Lever (J) upward to disengage the pin.
• Simultaneously, rotate Seat (K) to the most comfortable angle. To lock the seat in position by
Releasing Lever (J) and ensure the pin is fully engaged.
Circuit Breaker:.
If scooter’s circuit system malfunctions or over loaded, the circuit breaker will trip and automatically
shut down the power to ensure driver’s safety. After shut down the power, press button of Circuit
Breaker (B) to reactive the circuit system.
Free-Wheeling Lever:
The scooter can be pushed, when the Free-Wheeling Lever (L) is disengaged. To engage the
Free-Wheeling Lever (L) - Pull up the free-wheeling lever.
To disengage the Free-Wheeling Lever (L) - Push down the free-wheeling lever.
Instruction Booklet: Identification of Parts
06
IK
J
B
L

Basket assembling and disassembling:
• Place the Front Basket (M) to the bracket on the tiller.
• Remove the Front Basket (M) and place it aside.
Armrest assembling and angle adjustment:
• Adjust armrest to most comfortable length,
then lock the Knob (N).
• Adjust Screw (O) height to preferable armrest’s angle.
Seat height adjustment:
• Remove the seat, then screw, nut and washer from seat post.
• Adjust seat post to desired height, then attached tightly with screw, nut and washers.
• Assemble the seat back to its original position.
• Seat height adjustable 520mm / 545mm / 570mm.
Instruction Booklet: Identification of Parts
07
M
O
N

Your Abilize scooter is equipped with two sealed, maintenance free 12V. 22Ah.
Rechargeable batteries and one 24V/3A charger. Batteries must be charged before using
scooter for rst time and should be recharged after each day’s use. Be sure power switch
is in OFF position and free-wheeling lever is not in freewheel mode.
For safety reasons, only sealed non-spillable batteries that meet DOT CFR 173.159(d), IATA
Packing Instructions, and IATA Provision A67 shall be installed in the scooters. If you need
new batteries, contact your dealer. Only 12V. 22Ah Valve-regulated Lead Acid batteries
should be used.
• Insert battery charger cord into Charging Socket (P) on battery pack.
• Plug other end of Power Cable (Q) into a standard electrical wall outlet.
• LED Indication
LED (Power) - RED Light on : Power on LED (Charge) - ORANGE Light on : Charging
GREEN Light on : Fully charged
• Allow batteries to charge until charging indicator turns green. For optimum performance a rst
initial charge of 24 hours is recommended and 12 hour charge after every use.
• After indicator turns green, unplug battery charger from scooter and wall outlet.
• Do not charging simultaneously with battery box socket and optional charging socket, this will
cause serious risk.
• If at any time battery charger light ashes green over 40 minutes, this indicates abnormal
charging occurred. You should check the following:
1. Charger plug is correctly positioned.
2. Scooter is turned off.
3. If none of these are the problems, contact your local authorized dealer.
CAUTION: The time needed to recharge will vary depending on the depletion of the
batteries. Charging for longer than necessary will not harm the batteries. They can not be
overcharged.
Instruction Booklet: Charging the Batteries
08
P
Optional Charging
Socket (P1)

Instruction Booklet: Dissembling your Scooter
09
1. Seat Disassembling:
Remove seat by lifting Seat Rotation Lever (J). Then rotate Seat (K) and lift up away from scooter.
2. Battery Pack Disassembling:
As indication, pull Battery Pack Handle (R) to remove Battery Box (S) from scooter. Caution
: Battery Box is heavy. When lifting, please use correct lifting posture to avoid injury. Ask for
assistance if necessary.
CAUTION: When assembling battery pack (S), make sure to aim for the battery terminal
connection for proper electricity conductivity.
3. Front and Rear Frame Disassembling:
Hold front & rear frame with Release Lever (T) to disassemble front and rear frame.
Tiller Fold Method:
Turn the Cap (I) to fold down the Tiller (U) to the lowest position as shown in Figure 18. When the
Tiller (U) is in the lowest position it can be locked by the pin of tiller angle adjustment.
Competition of Disassembling:
The Scooter can be disassembled into 7 main parts as shown below.
CAUTION: Re-assembling your scooter by vice versa above disassembling procedures.
I
U
T
K
J
R
S