Charlton & Jenrick i920e User manual

Best of British fires, fireplaces & stoves
iRange Slim Electric Fire
Instruction Manual
Model:
i920e/i1100e/i1500e/i2000e
Please read the instructions carefully before installation
or use and keep for futurereference.

1. Important Safety Information...................................................................1
2.
Technical Specifications ......................................................................
3
3.
Parts And Hardware................................................................................
4
4. Appliance Dimensions ............................................................................
7
5.
Installation Instructions.......................................................................
8
6. Operating Instructions .......................................................................... 18
6A. Manual Control Panel................................................................... 19
6B. Remote Control......................................................................20
6C. APP Control ............................................................................. 23
7. Maintenance .................................................................................... 24
8. Service Parts list................................................................................... 25
9. Others.................................................................................................. 27
CONTENTS

1
 Read all of the instructions carefully before using the
appliance.
 For indoor use only. This appliance is not suitable for use
outside the house and only suitable for well insulated
spaces or occasional use.
 Do not use this appliance in the immediate surroundings of
a bath, a shower or a swimming pool.
 Do not use this fire as a free-standing appliance. It must
always be fixed to the wall, fireplace mantel, floor etc.
 This fire must not be located immediately below or in front
of a socket-outlet.
 This appliance must beearthed.
 This appliance must not be supplied through an external
switching device, such as a timer, or connected to the
circuit that is regularly switched on and off by utility in
order to avoid a hazard due to the inadvertent resetting of
the thermal cut out.
 If the power cord is damaged, it must be repaired by the
manufacturer, its authorized service center or professional
person in order to avoid ahazard.
The figure in the marking is “Do Not Cover”. Warning:
in order to avoid overheating, do not allow the appliance to
be covered or let the air inlet/outlet become obstructed.
Please note the warning on theappliance.
 To reduce the risk of fire, keep textiles, curtains, or any
other flammable material a minimum distance of 1 meter
from the air outlet.
 Keep the power cords away from hot surfaces and hot
conditions. Do not route the power lead in front of the
appliance.
 Do not use this fire in rooms that have explosive gas in
them (for example petrol), or if you are using solvents,
glue, aerosol spray or in flammable paints, as these may
catch fire.
1. IMPORTANT SAFETY INFORMATION

2
 This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
 Cleaning and user maintenance shall not be made by
children without supervision.
 Some parts of this product can become very hot and cause
burns. Particular attention has to be given where children
and vulnerable people arepresent.
 Do not use this appliance in small rooms when they are
occupied by persons not capable of leaving the room on
their own, unless constant supervision isprovided.
 Children should be supervised to ensure that they do not
play with the appliance.
 Keep the power plug accessible after installation for the
purpose of isolation.
 Children of less than 3 years should be kept away unless
continuously supervised or a fireguard is fitted.
 Children aged from 3 years and less than 8 years shall only
switch on/off the appliance provided that it has been
placed or installed in its intended normal operating
position and they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children aged from
3 years and less than 8 years shall not plug in, regulate and
clean the appliance or perform usermaintenance.
WARNING! Information below for authorized person or
service centre only:
A non- rewireable plug fitted with a 13A fuse is supplied .
Should the fuse or plug need replacing, and you are
competent to do so, it must be replaced with a 13A fuse
or plug being 13A BS1363A approved.

3
Model No. : i920e/i1100e/i1500e/i2000e
Supply Voltage: AC 230-240V 50Hz
Maximum power consumption: 1500W
Power for flame and fuel bed effect:
Model
i920e
i1100e
i1500e
i2000e
Power
13W
16W
22W
31W
Power for mood light:
Model
i920e
i1100e
i1500e
i2000e
Power
16W
16W
9.6W
16W
Heat Output:
Nominal heat output (Pnom): 1500W
Minimum heat output (indicative) (Pmin):750W
Maximum continuous heat output (Pmax): 1500W
Auxiliary Electricity Consumption:
At nominal heat output (elmax): 12.5W At
minimum heat output (elmin): 12W In
standby mode (elSB): 2.4W
Type of Heat Output / Room Temperature Control
Single stage heat output and no room temperature control
No
Two or more manual stages，no room temperature control
No
With mechanic thermostat room temperature control
No
With electronic room temperature control
Yes
Electronic room temperature control plus day timer
Yes
Electronic room temperature control plus week timer
Yes
Other Control Options
Room temperature control, with presence detection
No
Room temperature control, with open window detection
Yes
With distance control option
Yes
With adaptive start control
Yes
With working time limitation
No
With black bulb sensor
No
2. TECHNICAL SPECIFICATIONS

4
3. PARTS AND HARDWARE
A.
B.
C.
Firebox (1pc)
ST4*8 Screw (5pcs)
ST4*40 Screw
i920e/i1100e (4pcs)
i1500e/i2000e(6pcs)
D.
E.
F.
ST5*40 Screw
i920e/i1100e (14pcs)
i1500e/i2000e(18pcs)
Wall Plug
i920e/i1100e (14pcs)
i1500e/i2000e(18pcs)
Power Cord Bracket (1pc)
(Installer must fit before
leaving appliance)
Control PCB
Remote Control Receiver
Remote Control Transmitter
Hardware:
RC01-067B01
Software:V0
Hardware: RF290L V1.1
Frequency: FSK/OOK 433.92MHZ
Maximum transmit power: 10mW
Hardware:RF290A-TX-V1.3
Software:V2.4.1
3.1 Unpack the fire carefully and make sure that the appliance is intact
with no signs of damage caused by transport and no part has been
exposed to water. If in doubt, do not use the appliance and contact
your retailer.
3.2 Keep plastic wrapping away fromchildren.
3.3 Save the original packaging as this may be required in the event of
service complaint withproduct.
3.4 Ensure that all parts are removed from the packaging.

5
G. H. I.
Lower Brackets (2pcs)
(To be used when the wall
haning bracket(J) is used)
Glass Fixing Bracket (2pcs) Black Cover(2pcs)
J. K. L.
Wall hanging bracket is
attached on firebox (1pc)
Remove from the appliance
if you are not fixing to wall
Power Cord UK (1pc) Power Cord EU (1pc)
M. N. 0.
Edging Strips (2pcs) Edging Strips (2pcs) Edging Strips (2pcs)
P. Q. R.
Sucker(1pc) Logs (1set) Black Resin Chips (1set)
S. T. U.
Vermiculate (1set) Crystal Media (1set) Remote (1pc)

6
V.
AAA Battery (2pcs)
W.
Instruction Manual (1pc)
X.
Simplified Instruction (1pc)
Note: The following parts are provided only for i920e fire
To be used only when it is intended for a trim to be used
Top Trim Support (1pc)
LH/RH Trim Support (2pcs)
Bottom Trim Support (1pc)
ST4*8 Screw (8pcs)
ST4*25 Screw (2pcs)

7
Unit:mm
Model
A
B
C
D
E
F
G
H
i920e
924
954
342
486
167
180
12
73
i1100e
1104
1134
370
514
187
200
12
73
i1500e
1504
1534
370
514
187
200
12
73
i2000e
2004
2034
370
514
187
200
12
73
4. APPLIANCE DIMENSIONS
A
B
E
F
G
H
C
D

8
5.1 PREPARATION BEFORE INSTALLATION
TOOLS REQUIRED
A screwdriver, a spirit level and drill will be needed.
LOCATE THE APPLIANCE
Your new electric fireplace may be installed virtually anywhere in your home.
However, when choosing a location, ensure that the general instructions are
followed:
 For best result, install out of direct sunlight, water or very damp air.
 The appliance should be connected to an earthed electrical outlet
and it must be easily accessible to allow disconnection.
MINIMUM CLEARANCE TO COMBUSTIBLE
Sides
Floor
Back
Front
...........................0
...........................0
...........................0
...........................1000mm Minimum
Top (Mantel or TV) ....... 200mm Minimum
REMOVE WALL MOUNTING BRACKET
 Remove the wall mounting bracket from the rear of the appliance by
removing the securing screwsfrom each side.
5. INSTALLATION INSTRUCTIONS
200mm min
0mm min

9
ST4*8
CONNECT POWER CORD
It is very important that the plug is tightly located into the socket in rear of
appliance . It is essential that the retention clip provided is fixed in
place using the ST4*8 screw,ensuring a secure connection to the appliance.
It is recommended that you turn on and operate the appliance to check that
all functions and that there are no issues with the appliance.
CONNECT MOOD LIGHTS CABLE
The interface of the mood lights cable is on the rear of the appliance, near
the position of the power cord. Please also check the function after
connecting the mood light.
Note: Compatible mood lighting devices are available from Charlton & Jenrick
Ltd., Other brands may not be suitable and void the warranty.

10
CHOOSE ASPECT TYPE
The appliance can be installed in 3 different arrangements. They are as
follows:
 Front view (only the front window is visible)
When you unpack the appliance, you will notice that the side panels have
been fixed on the appliance, which makes the appliance visible on only
one front side.
 Corner Aspect (the front and one of the side windows are
visible)
Remove the side panel from the end you want to feature a glass panel.
Then take the top / bottom edging strips and the side edging strip and
fix them to the appliance using the screws taken from the removal of the
side panel(s)
 Panoramic Aspect (the front and both sides windows are
visible)
Repeat the corner aspect procedure on the opposite side of the
appliance.

11
REMOVE FRONT GLASS PANEL
Remove the 2 screws securing each transit retaining clip on both
side. Retain the screws for later use. Note: Clear plastic fixing
brackets and black covers are provided for the refixing of the
glass panel( see additional parts list on page 5 items H and I)
Use a suction cup provided to support the middle of the glass panel
and lift the panel upwards and pull it forwards at its lower edge.
Carefully lift glass away as shownbelow.

12
5.2 CHOICE OF INSTALLATION METHOD
The following is only given as a general guide because it can be
installed in so many ways. Provided you ensure electric connections
are safely made in accordance with the codes,various materials can
be used for the framework and cladding. But consideration should be
made to soften the internal surface of any cladding to minimise that
amplification of noise.
BUILT IN
Prepare the framework as a general guide only see picturebelow:
FRONT VIEW
CORNER VIEW
H

13
PANORAMIC VIEW
Unit: mm
Model
i920e
i1100e
i1500e
i2000e
W
930
1110
1510
2010
D
200
220
220
220
H
496
524
524
524
NOTE: Ensure a firm flat surface for positioning of the appliance
and securely fix to avoid vibration and movement of the appliance.
Ensure a minimum of 20mm clearance at the rear and the top of the
appliance before cladding for air movement.
Bend out the four brackets on the upper and lower edges of the
appliance, push the appliance into the framework and fix the
appliance with four ST4x40 screws provided to the framework.
It is important that the appliance is fitted securely as described
below.
H

14
Cladding the framework. Note:Hard surfaces can amplify sound.
Consider adding some underlay or like the inside surface of the
cladding .

15
middle hole
ST4*8
Arrange the fuel bed to your choice and reinstall the front glass
panel back. Secure the glass fixing bracket(H) with two ST4*8
screws and cover i t with the black covers( I ) for a clean
appearance. Note: Use the screws previouslyremoved.
WALL MOUNTED
Place the wall mounted bracket horizontally against the wall where you would
like to install the appliance. Mark the holes for screws, drill holes on the
marks, insert wall plugs(for masonry wall only) and fix the bracket to the wall
by ST5x40 screws . Its important that a secure fixing is made to the wall so
alternative fixings may be necessary for other wall types.
Attach the bottom mounting brackets to the appliance using four
ST4x8 screws provided.

16
x2
x2
Lift the appliance up and attach to the wall mounting bracket by
locating the fingers on the wall bracket into the rectangular openings
in the rear of theappliance.
Mark the hole position of the bottom mounting brackets, remove the
appliance from the wall, drill holes on marked and insert wallplugs.
Attach the appliance again on the bracket, secure each side with
screws previously removed.
Fix the lower rear of the appliance to the wall with the ST5*40
screws. Ensure the face of the appliance is vertical adjust or pack out
lower bracket as required. Arrange the fuel bed to your choice and
reinstall the front glass panel. Secure with glass fixing bracket(H)
with two ST4*8 screws and cover it with the black covers(I) for a
clean appearance, Note: Use the screws previously removed.

17
-
PREPARE FOR TRIM FITTING ONLY AVAILABLE FOR i920e
Note: A trim is not include and must be ordered separately.
The i920e can be fitted with a trim, the following instruction below
show how to prepare the appliance for the fitting of the trim using the
extra part provided. Take out the top, bottom components of the trim
support and side trim supports and install to the firebox with eight
ST4*8 screws as shown below.