Charlton & Jenrick EF16NC Parts list manual

Homeowner’s
Installation Instructions &
Operating Manual
Model: EF16NC
Please read the instructions carefully before installation or
use of this electric fire, retain for future reference.

APPLIANCE DATA
Supply Voltage AC 220-240V, 50Hz
Heating Element 1500W
Mains Cable 1 x 1.8m (approx)
DIMENSIONS :
481
592
400
401
76
552
158
100 260
400
85
459
381
IMPORTANT INFORMATION
This heater must not be located immediately below a socket-outlet.
This heater must be earthed. If in any doubt consult a suitable competent person.
In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this
appliance must not be supplied through an external switching device, such as a
timer, or connected to a circuit that is regularly switched on and off.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children shall not play with the appliance.
The Fuel bed contains some small glass beads which could be harmful to children
if swallowed, it is recommended that these are not used if children can access this
appliance.
Cleaning and user maintenance shall not be made by children without supervision.
It is recommended that a fireguard should be used for the protection of children,
the elderly and infirm. Fireguards should conform to BS 6539 (1984) (Fireguards
for use with solid fuel appliances).
Some parts of this product can become very hot and cause burns. Particular
attention has to be given where children and vulnerable people are present.
Do not use this fire as a free-standing appliance. It must always be fixed to the
wall, fireplace mantel, floor etc.
WARNING: In order to avoid overheating, do not cover the heater.
If the supply cord is damaged, it must be replaced by a special cord or assembly
available from the manufacturer or it’s service agent.
The meaning of figure in marking is “WARNING: DO NOT COVER”.

PARTS AND HARDWARE LIST
Part
Quantity
Instruction Manual
1pcs
Remote Control
1pcs
AAA Battery
2pcs
Screw ST5×25
4pcs
Drywall Anchors Φ8×40
4pcs
Plastic Shelf (for alternative fret shape)
1pc
Clear Beads
1set
Decorative Logs
1set
Washed Natural Coal
1set
INSTALLATION
NOTE:
Do Not use this Electric Fireplace if any part has been under water. Immediately call a
qualified service engineer to inspect and to replace any part of the electrical system if
necessary.
Unpacking the heater carefully, make sure that the appliance is intact with no signs of
damage caused by transport. If in doubt, do not use the appliance and contact your
retailer. Please save the original packaging as this may be required in the event of a
service complaint with the product.
Keep all plastic wrapping away from children.
Do not place the electric fire directly on carpets. This is to avoid possible discolouring
caused by the heat or blockage of air inlets.
Make sure that the plug or switched fused spur is accessible after the electric fire is
fitted.
If the supply cord is damaged, it must be replaced by a special cord or assembly
available from the manufacturer or its service agent.
Before connecting the appliance make sure that its rating corresponds to that of the
mains supply and the fuse is the correct rating.
The appliance should be located close to a suitable mains socket to enable connection.
The electrical socket must be easily accessible to allow disconnection.
MANTEL SIZE
W
H
D
Ho
Lo
Wo
Unit: mm
Opening Size For Insert
Positions for Fixing Screw
W
D
H
Wo
Ho
Lo
420
≥75
565
459
400
85

Installation of Insert:
420
565
400
459
85
¡ Ý80
Keyhole
slots Keyhole
slots
Step1: Carefully mark out the 4 fixing screw
positions as above (positions for fixing
screw)
Step2: Fixing to masonry, drill 4pcs Φ8 holes
on the wall. Put the plastic wall plug into the
hole. If the wall is timber, drill small pilot
holes and use screws provided but without
wall plugs
Step3: Fit 4 screws ST5×25 leaving
approximately 2mm between the panel
and the underside of the screw head.
Step4: Lift the insert into position so the
keyhole slots locate on the screw heads.
Magnets
Magnets
12.5
Step4: Tighten screws to secure appliance
Step5: Put 4pcs magnets (with the size of
18×18×12.5) onto the frame.
Fitting the Elite Fascia
Step6.1: Put the Elite Fascia onto front of the insert. Then lay the fuel bed on the opaque
surface using the Decorative Logs or the Washed Natural Coal and Clear Beads in an
arrangement that pleases you.

For the Other Fret Options, it may be necessary to change to Opaque Plastic shelf
to suit better the fret shape：If it is needed to replace the plastic shelf do it before
the installation of the insert from step1 to step5 as above.
Step6.2: To change the Opaque Plastic Shelf remove the 4 screws as shown, remove
shelf and replace fixing back in position with original screws
Then lay the fuel bed on the opaque surface using the Decorative Logs or the Washed
Natural Coal and Clear Beads in an arrangement that pleases you.
Typical Fuel Bed Coal and Beads
Typical Fuel Bed Logs and Beads
OPERATION
This appliance can be operated by both remote control and manual buttons. Once the
unit has been properly connected to an earthed electrical outlet, turn on the main
switch. A beep should be heard when the power is first applied.

NOTE: To use both remote and manual functions the main on/off switch must be
in the ‘on’ position.
Operating by Manual Button
Power Button
Flame Button
Heater Button
Main Switch
NOTE：The flame will always be on when the appliance is on.
Main switch
The main switch supplies power to all of the functions of the fireplace. This switch must
be in the “ON” position for any of the functions including the remote to work. To access
this switch it will be necessary to remove the fret cover.
Power button
Press once turns appliance and flame effects on. Press again turns appliance and
flame effects & heating off.
Flame button
By pressing the FLAME button, the unit will cycle through four flame effects.
Heater button
Press once turns the Fan on, and 10 seconds later the Low heat on. (Pilot light
illuminated●○)
Press again turns on High heat. (Pilot lights illuminated ●●)
Press third time turns heat off. 10 seconds later Fan off (Pilot lights illuminated ○○)
There are 3 levels you can cycle through including the OFF setting.

Multifunction Infrared Remote Handset
To Reset the Heater
Your heater includes a protection system that shuts off the heater if it overheats for any
reason:
1) Turn unit to “off”.
2) Unplug unit wait 5 minutes.
3) Plug in and turn “on”.
●Operating by Remote Handset
In order to protect the product from becoming too hot, there is a 10 second delay
when turning on the heater; also there is a 10 second delay when turning off the
heater fan.
Make sure the batteries are installed properly in the remote control.
The effective range of the remote control is up to 4 meters or 13 feet.
MAINTENANCE
Warning: Before any maintenance and/or cleaning the exterior of the
fireplace, disconnect the unit from the power supply and leave until cooled
off.
Remote Handset Battery Replacement
Replace with two AAA batteries. Make sure the batteries are installed correctly in the
remote control.
Maintenance of Motors
The motors used on the fan and flame effect are pre-lubricated for extended bearing life
and require no further lubrication. However, periodic cleaning/vacuuming of the
fan/heater unit is recommended.
ICON
TITLE
FUNCTION
POWER
Press once turns appliance and flame effects on. Press again
turns appliance and flame effects off.
FLAME
The fire has four flame effects, by pressing the flame effect
button the unit will cycle through each effect.
HEATER
Press once turns Low heat on. (Pilot lights illuminated●○)
Press again turns High heat on (Pilot lights illuminated ●●)
Press third time turns heater off. (Pilot lights illuminated ○○)
TEMP
Digital display shows the TEMP setting 23°C (default), with 14
settings circle from “OFF”, “16°C”to ”28°C”.
The TEMP will increase by 1°C up to 28°C when pressed each
time.
By pressing the TEMP for 3 Seconds, the digital display can
show between °C and °F.
TIMER
Cycles from OFF, 0.5H, 1H, 2H, 3H, 4H, 5H, 6H, 7H, 8H, to 9H.

Resetting the Thermal Cut-out Switch
The appliance is fitted with an Electronic Safety Control (E.S.). This is a safety device,
which switches off the fire if, for any reason, the appliance overheats, e.g. when
covered. If the heater stops operating whilst the flame effect continues normally, this
indicates that the E.S. Control is in operation. The E.S. Control can only be re-set after
the appliance has cooled down, in order to re-set the E.S. Control proceed as follows:
Switch off the appliance (Manual On/Off switch) and leave for approximately
10-15 minutes.
Remove any obstruction to the fan heater outlet or fan blades etc. Make sure
that the power supply is disconnected at the plug socket outlet whilst you do
this.
Switch on appliance and the E.S. Control will re-set.
Ensure that the appliance is functioning correctly. If the E.S. Control operates
again, the appliance should be checked by a competent Electrician.
Cleaning the Fireplace
You can clean the exterior of the fireplace with a soft, damp, lint-free cloth. Do not use
cleaning or polishing products. To remove fingerprints or other marks on the front glass
panel, use a soft, damp, lint-free cloth with a good quality household glass cleaner. The
front glass panel should always be completely dried with a clean, lint-free cloth or paper
towel.
Caution: Do not use abrasive cleaners on the glass panel. Do not spray
liquids directly onto any surface of the unit.
Warning: An authorised service representative should perform any
other servicing.
Environment Meaning of crossed –out wheeled dustbin:
Do not dispose of electrical appliances as unsorted municipal waste,
use separate collection facilities. Contact your local government for
information regarding the collection systems available. If electrical
appliances are disposed of in landfills or dumps, hazardous
substances can leak into the groundwater and get into the food
chain, damaging your health and well-being. When replacing old
appliances with new ones, the retailer is legally obligated to take
back your old appliance for disposals at least free of charge.
This fire complies with the European Safety Standards (LVD) EN 60335-2-30
and the European Electro Magnetic Compatibility (EMC) EN 55014-1, EN
55014-2 and EN 61000-3-2 and EN 61000-3-3 which covers the essential
requirements of the EC Council Directives and 2004/108/EC.