Cisco CP-8851 User manual

CP-8851 / CP-8861
Do Not Ship Enclosure with Phone Installed
[PHONE MUST BE INSTALLED ON-SITE]

- Due to the size and mass of this product, it is
Take into consideration before you install:
important that the Backbox is safely installed
according to these installation instructions.
- Make sure that the type of wall is capable of supporting
the system and use screws that are suitable for that type of wall.
- The system must be installed by qualied personnel, in
accordance with state and local building regulations.
- See sheet ve and ten for Conduit and Wall Mounting instructions.
CP-8851 / 9961 Mounting the Enclosure

Accessory Kits
Torx Sec. Bit & Spare Screw Kit
#6-32x5/8"Flat Head
Pin Torx Machine Screw
(Spare - 2 Pieces)
#00 Screw Driver Kit
Jumper Shunt #8 Hex Nut
#6-32 x3/16”
Button Head Torx
Machine Screw
(Spare)
(GND Lug)
Keypad Cover Accessory Kit
Hex L-Key
Coverplate
Mounting
Screw
Phone Mounting Screw Kit
Drilled Spanner Dirver Bit
Smaller
for Acrylic Bezel
Replacement
T-15 Pin Torx
Security Driver Bit

Cisco CP-8851 /
Cisco CP-8861
Then Connect Power Plug (1) &
Network Cable (2), etc. before
Install Mounting Bracket
Mounting
Bracket
Mounting
Screw (2 Pieces)
(1)
(2)
Remove Both
USB & KEM
Remove Handset &
Disconnect Cord from Phone.
Covers
Remove Handset, USB & KEM Covers,
Install all Cables then the Mounting Bracket

Plug in the USB Cable
USB Port
Right Angle
USB-A Plug
USB-B Plug in to
USB to Analog Audio Module
(See Sheet 6 of 10)
AUX
Cable
AUX

Tools Required:
1) Electric Powered Hand Drill
2) Drill Bit (Use Correct Drill Bit for Wood / Concrete)
Mount the Backbox Assembly
to the Wall
A) Prepare Hole on Drywall (with Stud Behind) / Concrete
B) Insert Stud Anchors in to Holes
C) Align Backbox Assembly Mounting Holes to Studs
Step 3
Figure Shown Typical Installation:
3) Leveler
4) Torque Wrench, Wrench and Socket
D) Tighten Washers and Nuts that included with Stud Anchors
E) Torque to Stud Anchors Manufacturer's Recommended ft./lbs.

110
USB-B
Black Wire to Terminal 4
Green Wire to Terminal 3
Yellow Wire to Terminal 2
Red Wire to Termianl 1
Terminal
Audio Module
USB to Analog
Hookswitch Cradle
Use Provided #00 Screw Driver
to Install Wires to Terminal Block
Connect Before Closing the Faceplate
Block
Handset Lanyard
Armored Cord
Handset Retainer
Factory Disconnected,
to Terminal 5
Red Wire
Black Wire
to Terminal 9
Black Wire
Black Wire
Hookswitch Cradle to Handset Connections
Armored Cord

Install Shunt on JP2
to Enable Auto Answer Mode
JP2
Shunt

Phone with
Backbox
Phone Mount
Assembly
Intall Phone with Phone Mount
to Backbox

Use Provided Security Torx
Driver Bit to Fasten Screws
to Backbox
Tool Required:
Electric Hand Drill or
Powered Screwdriver
Backbox
Assembly
Faceplate
Torx Screw (11x)
Assembly

12.992 [330.0]
DIMENSIONS ARE IN INCHES [MILLIMETER]
APPROX. 6.040 [153.4]
Fits 1/2" EMT
Connector & Conduit
(2 Places)
Hole Diameter ts 1/4” -20 Thread Size
8.661 [220.0]
4.331 [110.0]
2.087 [53.0]
15.197 [386.0]
2.874 [73.0]
4.724 [120.0]
4.724 [120.0]
1.996 [50.7]
1.526 [38.8]
1) 11/32" or 9mm Socket & Socket Wrench
Tool Required to Remove Hole Plug:
3.130 [79.5]
Ø0.512 [Ø13.0]
Ø0.315 [Ø8.0]
Ø0.827 [Ø21.0]
(6 Places)
SPAR II (for Use with
RTFM Access Hole Covered
Stud Anchors/Screw/Bolt
Dimensions and Features
Reserved for Biometric Reader /
RFID Reader Module Upgrade
Included Keypad Coverplate,
Customer Replaceable
Scratch Resistance Acrylic
Hookswitch Coverplate
Available for Handsfree
Operation, P/N: 611535A
Customer Replaceable
Armored Cord Handset with
Steel Lanyard
P/N: 031433D
P/N: 621028A
To Remove Nut Behind:
Use 1/4” / 6mm Socket
Coverplate Pre-Installed
Screw and Hex L-Key
(for Handsfree Operation)
Biometric / RFID)
by Security Torx Screw
(Included Two Spare & Torx Driver Bit)
Customer Replaceable
304 Stainless Steel Faceplate
P/N: 611578A
Security Torx Screw