CKD EVD-1000 Series User manual

INSTRUCTION MANUAL
•Read this Instruction Manual before using the product.
•Read the safety notes carefully.
•Keep this Instruction Manual in a safe and convenient place for future reference.
Digital Electro-pneumatic
Regulator
EVD-1000/3000 Series IO-Link Type
SM-A20758-A/3

SM-A20758-A/3 PREFACE
i 2020-10-06
PREFACE
Thank you for purchasing CKD's "EVD-1000/3000 Series IO-Link Type" digital electro-pneumatic
regulator.
This Instruction Manual contains basic matters such as installation and usage instructions in order to
ensure optimal performance of the product. Please read this Instruction Manual thoroughly and use the
product properly.
Keep this Instruction Manual in a safe place and be careful not to lose it.
Product specifications and appearances presented in this Instruction Manual are subject to change
without notice.
•The product is intended for users who have basic knowledge about materials, piping, electricity, and
mechanisms of pneumatic components. CKD shall not be responsible for accidents caused by
persons who selected or used the product without knowledge or sufficient training.
•Since there are a wide variety of customer applications, it is impossible for CKD to be aware of all of
them. Depending on the application or usage, the product may not be able to exercise its full
performance or an accident may occur due to fluid, piping, or other conditions. It is the responsibility
of the customer to check the product specifications and decide how the product shall be used in
accordance with the application and usage.

SM-A20758-A/3 SAFETY INFORMATION
ii 2020-10-06
SAFETY INFORMATION
When designing and manufacturing any device incorporating the product, the manufacturer has an
obligation to ensure that the device is safe. To that end, make sure that the safety of the machine
mechanism of the device, the pneumatic control circuit, and the electric system that controls such
mechanism is ensured.
To ensure the safety of device design and control, observe organization standards, relevant laws and
regulations, which include the following:
ISO 4414 and JIS B 8370 (the latest edition of each standard)
In order to use our products safely, it is important to select, use, handle, and maintain the products
properly.
Observe the warnings and precautions described in this Instruction Manual to ensure device safety.
Although various safety measures have been adopted in the product, customer's improper handling may
lead to an accident. To avoid this:
Thoroughly read and understand this Instruction Manual
before using the product.
To explicitly indicate the severity and likelihood of a potential harm or damage, precautions are classified
into three categories: "DANGER", "WARNING", and "CAUTION".
DANGER
Indicates an imminent hazard. Improper handling will cause death or serious
injury to people.
WARNING
Indicates a potential hazard. Improper handling may cause death or serious
injury to people.
CAUTION
Indicates a potential hazard. Improper handling may cause injury to people or
damage to property.
Precautions classified as "CAUTION" may still lead to serious results depending on the situation.
All precautions are equally important and must be observed.
Other general precautions and tips on using the product are indicated by the following icon.
Indicates general precautions and tips on using the product.

SM-A20758-A/3 SAFETY INFORMATION
iii 2020-10-06
Precautions on Product Use
DANGER
Use the product within the specified voltage range.
Applying voltage beyond the specified range may cause a malfunction, damage to the sensor,
electric shock, or fire.
Do not connect a load exceeding the rated output.
The output circuit may become damaged or a fire may occur.
Precautions on Design and Selection
WARNING
Do not supply anything other than compressed air.
Use clean compressed air that does not contain corrosive gases.
Use "ISO Class 1.3.2" equivalent oil-free clean dry air.
Understand the compressed air characteristics before designing a pneumatic pressure
circuit.
•Note that if the pressure needs to be stopped instantly at an emergency stop, the same
functions as those for mechanical, hydraulic, or electrical regulators cannot be expected.
•The air may pop out, flow out, or leak out due to its compression and expansion characteristics.
Make sure that the product can withstand the working environment before use.
•The product cannot be used in an atmosphere where corrosive gas, chemical liquid, solvent
vapor, water, and water vapor are present. If water drop, oil, or metal chips (such as spatter or
cutting chips) may come into contact with the product, provide an appropriate protection.
•The product cannot be used in an explosive gas atmosphere.
Consider the effects of an emergency stop on the electric circuit and power outages on the
cylinder when designing the system and selecting the product.
Install a pressure switch and a residual pressure exhaust valve on the compressed air supply
side of the device.
The pressure switch prevents the product from operating if the set pressure is not reached. The
residual pressure exhaust valve discharges compressed air remaining in the pneumatic pressure
circuit in order to prevent the residual pressure from causing the pneumatic components to operate
and to cause accidents.
Do not leave the pressure applied to the primary side of the product when the power is not
turned on.
The secondary side pressure may rise to the same level as the primary side pressure. If there are
safety concerns, design a system that ensures safety by providing measures such as installing a
valve on the primary side or the secondary side.
CAUTION
Use the product within the working pressure range.
Specify maintenance conditions in the instruction manual of the customer’s device.
Depending on the conditions of use, working environment, and maintenance conditions, the
functions of the product may decline significantly and the safety may not be ensured. Proper
maintenance will deliver optimum performance.
Use a constant voltage power supply.
Check for leakage currents from the external control devices to prevent a malfunction.
When using a control device such as a programmable controller, leakage currents from the control
device may affect the product and cause it to malfunction.
Reference value
For 24 VDC
1.8 mA or less

SM-A20758-A/3 SAFETY INFORMATION
iv 2020-10-06
CAUTION
If a stable reproducibility is necessary for the response time of the system, install a precision
regulator before the product.
The response time is affected by the working pressure and the capacity of the load on the
secondary side.
Take the following measures to prevent malfunctions caused by noise.
•Insert a line filter in the AC power supply line.
•Use a surge suppressor such as a CR or diode for the inductive load (such as a solenoid valve
or a relay) to remove noise at its source.
•Install the wiring for the product away from strong electric fields.
•Connect the shielded wires to the ground on the power side.
•Wire the power lines as short as possible.
•Do not share the power supply with noise-generating devices such as inverters or motors.
•Do not wire the power cables and the signal cables in parallel with other power lines.
Do not use air of poor quality.
•For the source of pneumatic air, use clean air from which solids, moisture, and oil have been
sufficiently removed with a dryer, an air filter, and an oil mist filter. Do not use air containing oil
that adversely affects the product characteristics.
Air filter
5μm
Air dryer
Oil mist filter
(removes oil)
Pressure switch
Pressure
reducing
valve
•When the secondary side pressure is reduced with an input signal, the secondary side air
passes through the product and is discharged from the exhaust port. Maintain the inside of the
pipes clean since contamination inside the secondary side pipes and the load also has an
adverse effect on the product characteristics.
Do not expect the pressure on the secondary side to remain for a long period. Take measures
to remove residual pressure as necessary.
The pressure on the secondary side will remain if the power is turned off while the pressure is
applied but not for a long period. Reduce the set pressure with an input signal and then turn off the
power or discharge the pressure using a residual pressure exhaust valve as necessary.
Make sure that the primary side pressure does not become lower than the minimum working
pressure (EVD-1100: set pressure +50 kPa, EVD-1500/1900: set pressure +100 kPa).
Not supplying the primary side pressure for a long period while the power is turned on will shorten
the product service life.
Before using the product as an air blow with the control pressure of the secondary side
released to the atmosphere, test the usage under actual conditions of use or contact CKD.
The pressure may fluctuate depending on the piping and blowing conditions.
Select a dryer, an air filter, an oil mist filter, and a regulator that can accommodate a flow rate
higher than the flow rate used for the product.
When using the product out of the specified conditions or for a special application, consult
CKD about the specifications.
Do not use the product where it is exposed to direct sunlight or where water, oil, and other
liquids may directly splash onto the product.
Do not install the product in places where moisture, saline matters, dusts, or cutting chips are
present and pressure is applied or reduced.
The degree of protection of the product is equivalent to IP40. The product cannot be used where
the temperature changes sharply or humidity is high as condensation may develop in the product
<Recommended circuit>

SM-A20758-A/3 SAFETY INFORMATION
v 2020-10-06
CAUTION
and cause damage.
If 0 MPa is required, bleed the secondary side or install a 3-way valve to release the pressure
to the atmosphere.
Although the pressure control range of the product includes 0 MPa, the pressure on the secondary
side will not be completely released (the pressure of 1%FS or less of the maximum control
pressure will remain).
Working conditions for CE compliance
This product conforms to the EMC Directive and CE standard. The standard for the immunity for
industrial environments applied to this product is EN61000-6-2; the following requirements must be
satisfied in order to conform to this standard:
Conditions
The evaluation of this product is performed by using a cable that has a power supply line and a
signal line, paired to assess the product’s performance.
This product is not equipped with surge protection. Implement surge protection measures on the
system side.
About UL standard
If this product is being used as a UL-compliant product, please take care the below.
•Maximum surrounding air temperature rating of 50°C or equivalent.
•Please use the "Class 2" power supply.
UL File No.
UL Standard
Description
E339318
UL 508
Industrial Control Equipment

SM-A20758-A/3 CONTENTS
vi 2020-10-06
CONTENTS
PREFACE........................................................................................................................... i
SAFETY INFORMATION .................................................................................................. ii
Precautions on Product Use..........................................................................................iii
Precautions on Design and Selection ...........................................................................iii
CONTENTS...................................................................................................................... vi
1. PRODUCT OVERVIEW ............................................................................................. 1
Part Name........................................................................................................... 1
Body................................................................................................................1
Names and functions of display and operation panel....................................3
Functions.............................................................................................................4
Model Number Indication.................................................................................... 6
Specifications...................................................................................................... 8
Communication specifications .......................................................................... 14
General......................................................................................................... 14
On demand data........................................................................................... 15
Parameter and commands...........................................................................16
Process data IN............................................................................................19
Process data OUT........................................................................................20
Observation ..................................................................................................20
Diagnosis......................................................................................................21
Dimensions .......................................................................................................22
Internal Structure ..............................................................................................24
2. INSTALLATION ....................................................................................................... 26
Mounting ...........................................................................................................26
Piping ................................................................................................................28
Seal material.................................................................................................28
Wiring................................................................................................................ 29
M12 connector.............................................................................................. 30
Cable connection.......................................................................................... 31
3. USAGE..................................................................................................................... 32
Checking the Set Value (RUN Mode)...............................................................32
Input signal type setting................................................................................ 32
Automatic power off...................................................................................... 33
Switch output................................................................................................33
Proportional value change ........................................................................... 34
Unit setting.................................................................................................... 34
Operation while communication error occurred setting ............................... 35
Control stop function at zero input signal.....................................................35
How to Set (Setting Mode)................................................................................36
Setting ranges .............................................................................................. 36
Key lock ........................................................................................................ 37
Input signal ...................................................................................................37
Automatic power off...................................................................................... 39
Switch output................................................................................................40
Proportional value change setting................................................................ 42
Unit change (KA type) .................................................................................. 44
Operation while communication error occurred setting ............................... 45
Control stop function at zero input signal.....................................................46
Factory setting mode (initialization)............................................................47

SM-A20758-A/3 CONTENTS
vii 2020-10-06
Control procedure using IO-Link communication .............................................48
Normal Mode................................................................................................48
Preset input .................................................................................................. 50
Direct memory input ..................................................................................... 52
Monitoring overactive state of solenoid valve...................................................53
Monitoring overactive state of solenoid valve ..............................................53
Acquired data ............................................................................................... 53
How to obtain data ....................................................................................... 54
4. MAINTENANCE AND INSPECTION....................................................................... 55
Periodic Inspection............................................................................................ 55
5. TROUBLESHOOTING............................................................................................. 56
Problems, Causes, and Solutions ....................................................................56
Error Code ........................................................................................................58
6. OPTION.................................................................................................................... 59
Optional Part Model Number ............................................................................ 59
7. References.............................................................................................................. 61
Operating principle of digital electro-pneumatic regulator................................61
Operating principle ....................................................................................... 61
About overactive state..................................................................................63
8. WARRANTY PROVISIONS..................................................................................... 64
Warranty Conditions ......................................................................................... 64
Warranty Period ................................................................................................ 64

SM-A20758-A/3 1. PRODUCT OVERVIEW
1 2020-10-06
1. PRODUCT OVERVIEW
Part Name
Body
◼EVD-1000 Series
LED display
Operation keys
Threaded hole for mounting the bracket
Port R
(pilot air exhaust)
Exhaust port
(main air exhaust)
*Please attach the unit label sticker
according to the unit to be used.
Unit label sticker
(Accessory)
Option KA type only
M12,4pin connector

SM-A20758-A/3 1. PRODUCT OVERVIEW
2 2020-10-06
◼EVD-3000 Series
LED display
Threaded hole for mounting the bracket
Operation keys
Port R
(pilot air exhaust)
Exhaust port
(main air exhaust)
M12,4pin connector
*Please attach the unit label sticker
according to the unit to be used.
Unit label sticker
(Accessory)
Option KA type only

SM-A20758-A/3 1. PRODUCT OVERVIEW
3 2020-10-06
Names and functions of display and operation panel
Output display (red)
⚫"F" is displayed during function setting
confirmation.
⚫"E" is lit when the error output is on.
* If there is an upper or lower limit in the function setting,
one of the following is displayed.
or
The red dot blinks during IO-Link
communication.
When communication is not
established, the red dot lights.
key
⚫Press to start various setting modes.
⚫Press to confirm values during data
entry.
key
⚫Press to select the digit place of values during
data entry.
3-digit number LED display (green)
⚫In the RUN mode (pressure display), the pressure or
function setting data is displayed.
* In the function setting data display mode, the setting
mode number and setting are displayed.
⚫During data entry, a value or other types of data are
displayed.
⚫Upon error display, the error code number is displayed.
<Pressure display> <Function setting data display>
<Upon error output>
key
⚫In the RUN mode (pressure display),
press to display various settings one by
one.
⚫Press to select a setting item during
data entry.
⚫Press to increase the value during data
entry.
Code no.
Setting
Setting mode
no.

SM-A20758-A/3 1. PRODUCT OVERVIEW
4 2020-10-06
Functions
Screen
Description
Details (run mode)
Setting details (setting mode)
Related
page
Pressure
display
Indicates the secondary side
pressure with 3-digit number.
The display value is converted to
the set unit.
Screen F1
Input signal
type setting
Indicates the selected input
signal type, current pressure
value and unit.
*This function is set to the
normal mode "F1.Io".
Input type can be selected from
normal mode / preset / direct
memory. For preset / direct input,
enter the setting value on this
screen. Preset input values can
also be set via IO-Link
communication. (Direct input
value can be set only on this
screen.)
P.32
P.37
Screen F2
Zero/span
adjustment
No available
“F2.--" is displayed.
Screen F3
Automatic
power off
Indicates whether automatic
power off is enabled or disabled.
*This function is set to disabled
"F3.-- " at the factory setting.
Select to enable or disable the
automatic power off.
Note: The automatic power off
time is set to approximately
one minute and cannot be
changed.
P.33
P.39
Screen F4
Switch
output
Indicates whether switch output
is enabled or disabled and the
set value.
For "Mode 1 enabled", "F4.1" or
"F4.2" is displayed, and the
switch No. (1 or 2) and Mode (1),
"−" tolerance range set value (L)
and "+" tolerance range set
value (H) are displayed in order.
For "Mode 2 enabled", "F4.1" or
"F4.2" is displayed, and the
switch No. (1 or 2) and Mode (2),
lower set value (L) and upper set
value (H) are displayed in order.
*This function is set to disabled
"F4._1"⇔"1 --"
"F4._2"⇔"2 --"
at the factory setting.
Select to enable or disable the
switch output.
If enabled, "Mode 1" and "Mode
2" can be selected.
+/− tolerance values and
upper/lower values can be set
randomly.
P.33
P.40
To screen F5
△
△
△
△
△
△

SM-A20758-A/3 1. PRODUCT OVERVIEW
5 2020-10-06
From screen F4
Screen
Description
Details (run mode)
Setting details (setting mode)
Related
page
Screen F5
Proportional
value
change
Indicates the validity of
proportional value
change and its set level.
For "Higher proportional value",
"F5.H" is displayed.
For "Lower proportional value",
"F5.L-" and
its set level is displayed
alternately.
* The value is set to standard
value "F5.--" at the factory
setting.
Select to either using the
standard value or changing the
proportional value.
The proportional value level
can
be set in this mode only if
"Lower
proportional value" is selected
(10 levels).
P.34
P.42
Screen F6
Unit setting
Indicates the pressure unit.
For Unit change none (Symbol:
Blank), "F6.--" is displayed.
For Unit change available
(Symbol: KA), "F6." and unit
are displayed alternately.
*This function is set to "kPa" at
the factory setting.
Units can be selected from
“kPa”, “psi”, and “bar” only
when the unit change available
(Symbol: KA) is selected.
Unit cannot be selected when
the unit change none (Symbol:
Blank) is selected.
P.34
P.44
Screen F7
Operation
setting when
the
communication
error occurs
Indicates the operation setting
when the communication error
occurs.
*This function is set to " HOLD:
F7. Ho" at the factory setting.
The operation of pressure
control when IO-Link
communication occurs can be
set from "HOLD" or "CLEAR".
P.35
P.44
Screen F8
Control stop
function at zero
input signal
Indicates the control stop
function at zero input signal.
*This function is set to disabled
"F8.-- " at the factory setting.
The control stop function at
zero input signal can be
selected "enable" or "disable".
P.35
P.46
△
△
△

SM-A20758-A/3 1. PRODUCT OVERVIEW
6 2020-10-06
Model Number Indication
◼EVD-1000 Series
*Symbol ○
dKA type is only available outside Japan.
EVD-1 - - -
Symbol
Description
Pressure specification
100
100kPa
500
500kPa
900
900kPa
Input specification
C
IO-Link
Port size
08
Rc1/4
08G
G1/4
08N
NPT1/4
Unit change
Blank
Unit change none
KA
Unit change available
Option
Cable option
Blank
None
MS
IO-Link
M12 straight(female)
/M12 straight(male), 3m
ML
IO-Link
M12 L type(female)
/M12 straight(male), 3m
MM
IO-Link
M12 One side straight
(female), 3m
Bracket option
Blank
None
B1
B-type bracket, floor mounted
L1
L-type bracket, wall mounted
Power supply voltage
3
24 VDC
a
m
eb
a
b
c
d
e
f
3
500
08
KA
MS
C
Unit change
d
Port size
c
Input specification
b
Pressure specification
a
Option
e
Power supply
voltage
f

SM-A20758-A/3 1. PRODUCT OVERVIEW
7 2020-10-06
◼EVD-3000 Series
*Symbol ○
dKA type is only available outside Japan.
EVD-3 - - -
Symbol
Description
Pressure specification
100
100kPa
500
500kPa
900
900kPa
Input specification
C
IO-Link
Port size
08
Rc1/4
10
Rc3/8
08G
G1/4
10G
G3/8
08N
NPT1/4
10N
NPT3/8
Unit change
Blank
Unit change none
KA
Unit change available
Option
Cable option
Blank
None
MS
IO-Link
M12 straight(female)
/M12 straight(male), 3m
ML
IO-Link
M12 L type(female)
/M12 straight(male), 3m
MM
IO-Link
M12 One side straight
(female), 3m
Bracket option
Blank
None
B1
B-type bracket, floor mounted
L1
L-type bracket, wall mounted
Power supply voltage
3
24 VDC
a
b
c
d
e
f
3
500
08
KA
MS
C
Pressure specification
a
Input specification
b
Port size
c
Unit change
d
Option
e
Power supply
voltage
f

SM-A20758-A/3 1. PRODUCT OVERVIEW
8 2020-10-06
Specifications
◼EVD-1100-C (maximum pressure: 100 kPa)
Item
EVD-1100-C [*2] [*3]- [*4] [*] -3
Working fluid
Clean compressed air (equivalent to ISO Class 1. 3. 2)
Max. working pressure
160 kPa
Min. working pressure
Control pressure +50 kPa
Proof pressure
Inlet side
240 kPa
Outlet side
150 kPa
Pressure control range
Note 1
0 kPa to 100 kPa
Power supply voltage
24 VDC ± 10% (stabilized power supply with ripple rate of 1% or less)
Current consumption
Note 2
0.15 A or less (starting current is 0.6 A or less when the power is turned on)
(Port type A)
Input signal
IO-Link
Preset input
8-point (IO-Link)
Pressure display
Display method
3-digit 7-segment LED,
display accuracy: ±2%FS or less
Display range
0 kPa to 100 kPa
Display
resolution
1 kPa
Direct memory setting
1 kPa to 100 kPa
(min. set width 1 kPa/set resolution 1 kPa)
Hysteresis
Note 3
0.5%FS or less
Linearity
Note 3
±0.3%FS or less
Resolution
Note 3
0.2%FS or less
Repeatability
Note 3
0.3%FS or less
Temperature
characteristics
Zero point
fluctuation
±0.15%FS/°C or less
Span drift
±0.07%FS/°C or less
Max. flow rate (ANR)
Note 4
60 L/min
Step response Note 5
No load
0.2 sec or less
With 1000 cm3
load
0.8 sec or less
Vibration resistance
98 m/ s2or less
Ambient temperature
5°C to 50°C
Fluid temperature
5°C to 50°C
Port size [*2]
[*2] =08 Rc1/4
[*2] =08G G1/4
[*2] =08N NPT1/4
Unit change [*3]
Note 6
None
Without Unit change function
KA
Unit change kPa / psi / bar (Accessory ： Unit label sticker psi / bar)
Mounting orientation
No restriction
Weight (body)
250 g
Protection circuit
Power reverse connection protection
Note 1: There is 1%FS or less residual pressure (1 kPa or less) when the input signal is 0%.
Note 2: Use the power supply unit that have the power supply ability sufficiently to each port of IO-Link master.
Note 3: The above characteristics are based on the condition that power supply voltage is 24 VDC ± 0.1 VDC, working pressure
is set to maximum control pressure +50 kPa, and control pressure is 10% to 90% (with no load, ambient temperature of
25°C ± 3°C).
Also, the specified values are only for when the secondary side is a closed circuit and pressure fluctuations will occur if
the product is used for blowing or similar applications.
Note 4: The above characteristics are based on the condition that working pressure and control pressure are set to their maximum.
Note 5: The above characteristics are based on the condition that working pressure is set to maximum and the step amount is
changed from 50%F.S.→100%F.S.
50%F.S.→60%F.S.
50%F.S.→40%F.S.
Note 6: KA type is only available outside Japan.

SM-A20758-A/3 1. PRODUCT OVERVIEW
9 2020-10-06
◼EVD-1500-C (maximum pressure: 500 kPa)
Item
EVD-1500-C [*2] [*3]- [*4] [*5]-3
Working fluid
Clean compressed air (equivalent to ISO Class 1. 3. 2)
Max. working pressure
700 kPa
Min. working pressure
Control pressure +100 kPa
Proof pressure
Inlet side
1050 kPa
Outlet side
750 kPa
Pressure control range
Note 1
0 kPa to 500 kPa
Power supply voltage
24 VDC ± 10% (stabilized power supply with ripple rate of 1% or less)
Current consumption
Note 2
0.15 A or less (starting current is 0.6 A or less when the power is turned on)
(Port type A)
Input signal
IO-Link
Preset input
8-point (IO-Link)
Pressure display
Display method
3-digit 7-segment LED,
display accuracy: ±2%FS or less
Display range
0 kPa to 500 kPa
Display
resolution
1 kPa
Direct memory setting
5 kPa to 500 kPa
(min. set width 1 kPa/set resolution 1 kPa)
Hysteresis
Note 3
0.5%FS or less
Linearity
Note 3
±0.3%FS or less
Resolution
Note 3
0.2%FS or less
Repeatability
Note 3
0.3%FS or less
Temperature
characteristics
Zero point
fluctuation
±0.15%FS/°C or less
Span drift
±0.07%FS/°C or less
Max. flow rate (ANR)
Note 4
400 L/min
Step response Note 5
No load
0.2 sec or less
With 1000 cm3
load
0.8 sec or less
Vibration resistance
98 m/ s2or less
Ambient temperature
5°C to 50°C
Fluid temperature
5°C to 50°C
Port size [*2]
[*2] =08 Rc1/4
[*2] =08G G1/4
[*2] =08N NPT1/4
Unit change [*3]
Note 6
None
Without Unit change function
KA
Unit change kPa / psi / bar (Accessory ： Unit label sticker psi / bar)
Mounting orientation
No restriction
Weight (body)
250 g
Protection circuit
Power reverse connection protection
Note 1: There is 1%FS or less residual pressure (5 kPa or less) when the input signal is 0%.
Note 2: Use the power supply unit that have the power supply ability sufficiently to each port of IO-Link master.
Note 3: The above characteristics are based on the condition that power supply voltage is 24 VDC ± 0.1 VDC, working pressure
is set to maximum control pressure +100 kPa, and control pressure is 10% to 90% (with no load, ambient temperature of
25°C ± 3°C).
Also, the specified values are only for when the secondary side is a closed circuit and pressure fluctuations will occur if
the product is used for blowing or similar applications.
Note 4: The above characteristics are based on the condition that working pressure and control pressure are set to their maximum.
Note 5: The above characteristics are based on the condition that working pressure is set to maximum and the step amount is
changed from 50%F.S.→100%F.S.
50%F.S.→60%F.S.
50%F.S.→40%F.S.
Note 6: KA type is only available outside Japan.

SM-A20758-A/3 1. PRODUCT OVERVIEW
10 2020-10-06
◼EVD-1900-C (maximum pressure: 900 kPa)
Item
EVD-1900-C [*2] [*3]- [*4] [*5]-3
Working fluid
Clean compressed air (equivalent to ISO Class 1. 3. 2)
Max. working pressure
1000 kPa
Min. working pressure
Control pressure +100 kPa
Proof pressure
Inlet side
1500 kPa
Outlet side
1350 kPa
Pressure control range
Note 1
0 kPa to 900 kPa
Power supply voltage
24 VDC ± 10% (stabilized power supply with ripple rate of 1% or less)
Current consumption
Note 2
0.15 A or less (starting current is 0.6 A or less when the power is turned on)
(Port type A)
Input signal
IO-Link
Preset input
8-point (IO-Link)
Pressure display
Display method
3-digit 7-segment LED,
display accuracy: ±2%FS or less
Display range
0 kPa to 900 kPa
Display
resolution
1 kPa
Direct memory setting
9 kPa to 900 kPa
(min. set width 1 kPa/set resolution 2kPa)
Hysteresis
Note 3
0.5%FS or less
Linearity
Note 3
±0.3%FS or less
Resolution
Note 3
0.2%FS or less
Repeatability
Note 3
0.3%FS or less
Temperature
characteristics
Zero point
fluctuation
±0.15%FS/°C or less
Span drift
±0.07%FS/°C or less
Max. flow rate (ANR)
Note 4
400 L/min
Step response Note 5
No load
0.2 sec or less
With 1000 cm3
load
0.8 sec or less
Vibration resistance
98 m/ s2or less
Ambient temperature
5°C to 50°C
Fluid temperature
5°C to 50°C
Port size [*2]
[*2] =08 Rc1/4
[*2] =08G G1/4
[*2] =08N NPT1/4
Unit change [*3]
Note 6
None
Without Unit change function
KA
Unit change kPa / psi / bar (Accessory ： Unit label sticker psi / bar)
Mounting orientation
No restriction
Weight (body)
250 g
Protection circuit
Power reverse connection protection
Note 1: There is 1%FS or less residual pressure (9 kPa or less) when the input signal is 0%.
Note 2: Use the power supply unit that have the power supply ability sufficiently to each port of IO-Link master.
Note 3: The above characteristics are based on the condition that power supply voltage is 24 VDC ± 0.1 VDC, working pressure
is set to maximum control pressure +100 kPa, and control pressure is 10% to 90% (with no load, ambient temperature of
25°C ± 3°C).
Also, the specified values are only for when the secondary side is a closed circuit and pressure fluctuations will occur if
the product is used for blowing or similar applications.
Note 4: The above characteristics are based on the condition that working pressure and control pressure are set to their maximum.
Note 5: The above characteristics are based on the condition that working pressure is set to maximum and the step amount is
changed from 50%F.S.→100%F.S.
50%F.S.→60%F.S.
50%F.S.→40%F.S.
Note 6: KA type is only available outside Japan.

SM-A20758-A/3 1. PRODUCT OVERVIEW
11 2020-10-06
◼EVD-3100-C (maximum pressure:100kPa)
Item
EVD-3100- C [*2] [*3]- [*4] [*5]-3
Working fluid
Clean compressed air (equivalent to ISO Class 1. 3. 2)
Max. working pressure
160 kPa
Min. working pressure
Control pressure +50 kPa
Proof pressure
Inlet side
240 kPa
Outlet side
150 kPa
Pressure control range
Note 1
0 kPa to 100 kPa
Power supply voltage
24 VDC ± 10% (stabilized power supply with ripple rate of 1% or less)
Current consumption
Note 2
0.15 A or less (starting current is 0.6 A or less when the power is turned on)
(Port type A)
Input signal
IO-Link
Preset input
8-point (IO-Link)
Pressure display
Display method
3-digit 7-segment LED,
display accuracy: ±2%FS or less
Display range
0 kPa to 100 kPa
Display
resolution
1 kPa
Direct memory setting
1 kPa to 100 kPa
(min. set width 1 kPa/set resolution 1 kPa)
Hysteresis
Note 3
0.5%FS or less
Linearity
Note 3
±0.3%FS or less
Resolution
Note 3
0.2%FS or less
Repeatability
Note 3
0.3%FS or less
Temperature
characteristics
Zero point
fluctuation
±0.15%FS/°C or less
Span drift
±0.07%FS/°C or less
Max. flow rate (ANR)
Note 4
700 L / min
Step response Note 5
No load
0.2 sec or less
With 1000 cm3
load
0.8 sec or less
Vibration resistance
98 m/ s2or less
Ambient temperature
5°C to 50°C
Fluid temperature
5°C to 50°C
Port size [*2]
IN, OUT Port
[*2] =08 Rc1/4, [*2] =10 Rc3/8
[*2] =08G G1/4, [*2] =10G G3/8
[*2] =08N NPT1/4, [*2] =10N NPT3/8
EXH Port
[*2]=08,10 Rc3/8
[*2]=08G,10G G3/8
[*2]=08N,10N NPT3/8
Unit change [*3]
Note 6
None
Without Unit change function
KA
Unit change kPa / psi / bar (Accessory ： Unit label sticker psi / bar)
Mounting orientation
No restriction
Weight (body)
470 g
Protection circuit
Power reverse connection protection
Note 1: There is 1%FS or less residual pressure (1 kPa or less) when the input signal is 0%.
Note 2: Use the power supply unit that have the power supply ability sufficiently to each port of IO-Link master.
Note 3: The above characteristics are based on the condition that power supply voltage is 24 VDC ± 0.1 VDC, working pressure
is set to maximum control pressure +50 kPa, and control pressure is 10% to 90% (with no load, ambient temperature of
25°C ± 3°C).
Also, the specified values are only for when the secondary side is a closed circuit and pressure fluctuations will occur if
the product is used for blowing or similar applications.
Note 4: The above characteristics are based on the condition that working pressure and control pressure are set to their maximum.
Note 5: The above characteristics are based on the condition that working pressure is set to maximum and the step amount is
changed from 50%F.S.→100%F.S.
50%F.S.→60%F.S.
50%F.S.→40%F.S.
Note 6: KA type is only available outside Japan.

SM-A20758-A/3 1. PRODUCT OVERVIEW
12 2020-10-06
◼EVD-3500-C (maximum pressure:500kPa)
Item
EVD-3500- C [*2] [*3]- [*4] [*5]-3
Working fluid
Clean compressed air (equivalent to ISO Class 1. 3. 2)
Max. working pressure
700 kPa
Min. working pressure
Control pressure +100 kPa
Proof pressure
Inlet side
1050 kPa
Outlet side
750 kPa
Pressure control range
Note 1
0 kPa to 500 kPa
Power supply voltage
24 VDC ± 10% (stabilized power supply with ripple rate of 1% or less)
Current consumption
Note 2
0.15 A or less (starting current is 0.6 A or less when the power is turned on)
(Port type A)
Input signal
IO-Link
Preset input
8-point (IO-Link)
Pressure display
Display method
3-digit 7-segment LED,
display accuracy: ±2%FS or less
Display range
0 kPa to 500 kPa
Display
resolution
1 kPa
Direct memory setting
5 kPa to 500 kPa
(min. set width 1 kPa/set resolution 1 kPa)
Hysteresis
Note 3
0.5%FS or less
Linearity
Note 3
±0.3%FS or less
Resolution
Note 3
0.2%FS or less
Repeatability
Note 3
0.3%FS or less
Temperature
characteristics
Zero point
fluctuation
±0.15%FS/°C or less
Span drift
±0.07%FS/°C or less
Max. flow rate (ANR)
Note 4
1500 L / min
Step response Note 5
No load
0.2 sec or less
With 1000 cm3
load
0.8 sec or less
Vibration resistance
98 m/ s2or less
Ambient temperature
5°C to 50°C
Fluid temperature
5°C to 50°C
Port size [*2]
IN, OUT Port
[*2] =08 Rc1/4, [*2] =10 Rc3/8
[*2] =08G G1/4, [*2] =10G G3/8
[*2] =08N NPT1/4, [*2] =10N NPT3/8
EXH Port
[*2]=08,10 Rc3/8
[*2]=08G,10G G3/8
[*2]=08N,10N NPT3/8
Unit change [*3]
Note 6
None
Without Unit change function
KA
Unit change kPa / psi / bar (Accessory ： Unit label sticker psi / bar)
Mounting orientation
No restriction
Weight (body)
470 g
Protection circuit
Power reverse connection protection
Note 1: There is 1%FS or less residual pressure (5 kPa or less) when the input signal is 0%.
Note 2: Use the power supply unit that have the power supply ability sufficiently to each port of IO-Link master.
Note 3: The above characteristics are based on the condition that power supply voltage is 24 VDC ± 0.1 VDC, working pressure
is set to maximum control pressure +100 kPa, and control pressure is 10% to 90% (with no load, ambient temperature of
25°C ± 3°C).
Also, the specified values are only for when the secondary side is a closed circuit and pressure fluctuations will occur if
the product is used for blowing or similar applications.
Note 4: The above characteristics are based on the condition that working pressure and control pressure are set to their maximum.
Note 5: The above characteristics are based on the condition that working pressure is set to maximum and the step amount is
changed from 50%F.S.→100%F.S.
50%F.S.→60%F.S.
50%F.S.→40%F.S.
Note 6: KA type is only available outside Japan.